MP Laghu Udyog Nigam Limited Tender

Elect. SOR. Page No. 95 I No. 42.5.2 Supplying and drawing All Aluminum Alloy conductor (AAAC) of approved make confirming to IS 398-1979 Pt. IV, including binding at existing insulator, jointing, jumpering, tearing off, connecting etc. as required including clearing of obstacles (if any) 42.5.2 AAAC 0.05 sq inch (55 Sq.mm Al. EQ. ) - (Rabbbit)

Elect. SOR. Page No. 96 I No. 42.14 Erection of RS Joist pole / 'H' Beam / steel tubular / steel rail pole of length exceeding 10 metres but not exceeding 13 metres in cement concrete M-10 (1 cement:3 core sand: 6 graded stone aggregate 40mm nominal size) base, foundation, muffing including excavation and back refilling etc. as required.

Elect. SOR. Page No. 99 I No. 42.36 Supply, fabrication and erection of Angle/Chanel/Flat iron fitting for over head line & sub-station etc such as 'D' bracket, cross arms, top clamp, 'V' cross arms, Back/Support clamps or other similar work etc. including nut bolts of required size, making holes, fabrication, welding, cutting, etc. and painting with one coat of red oxide paint & two coat of aluminium paint as required as per specification.

Elect. SOR. Page No. 100 I No. 42.46 Supplying and erection of 11kV (5 KN) Polymer pin insulator complete with long steel head G.I. pin, nut, washer etc. As required.

Elect. SOR. Page No. 100 I No. 42.47 Supplying and erection of 11kV (45 KN) Polymer disc insulator for 11kV overhead lines with galvanized insulator fittings, ball and socket type, and complete with galvanized strain clamp, bolts, nuts washer etc. as required.

Elect. SOR. Page No. 102 I No. 42.61 Supply & fixing anti climbing device with 2 ply G.I. Barbed wire 1 Kg. per pole complete as per specification.

Elect. SOR. Page No. 102 I No. 42.62 Supply, laying and fixing of G.I. earth coil of 4mm dia G.I. wire having 120 turns of nearly 50mm dia. and 3 mt. Long tail in existing pit duly earthed with pole etc complete as required as per specification.

Elect. SOR. Page No. 102 I No. 42.63 Supplying and fixing 33/11/0.4 KV enamel coated danger board size 200x250mm with clamp on existing HT/LT structure / poles.

Elect. SOR. Page No. 106 I No. 42.85.2.5 Supplying & drawing / laying of PVC insulated XLPE Aerial bunch power cable conductor H2/H4 grade Aluminium Solid/stranded confirming to IS-14255- 1995, Alu. Alloy insulated messenger 1100 volts grade cable of approved make in Air with necessary material as per specification of required size as mentioned below – 42.85.2 (ii) Single Core cable( Insulated neutral messenger) 42.85.2.5 (e) 3x95 Sq.mm, 1x16(St.Light), 1x50( Insulated neutral messenger)

Elect. SOR. Page No. 106 I No. 42.86 Supplying & fixing of Aerial bunch cable accessories suspension clamps i/c required attachment for single core cable of approved make on pole with clamp, necessary material as per specification for required size.

Elect. SOR. Page No. 107 I No. 42.89.1.4 Supplying & fixing of Spring loaded bus bar screw less connector with enclosure of approved make including required clamps, nut, bolt, connection, testing as per specification to complete the job. 106 42.89.1 Single Phase. 42.89.1.4 1Ph, 1In+5Out.

Elect. SOR. Page No. 107 I No. 42.89.2.2 3Ph, 1In+4 Out

Elect. SOR. Page No. 98 I No. 42.22 Supplying and erection of stay set complete with 19/20mm.dia 1.8 metre long stay rod, turn buckle, ancher plate of size 300mm x 300mm x 7.5mm, thimble, stay clamps, bow tightener, 7/4.00 dia G.I. stay wire etc. in cement concrete M-10 (1 Cement : 3 Coarse and : 6 granded stone aggregate 40mm nominal size) foundation including excavation and back refilling etc. as required.

Elect. SOR. Page No. 106 I No. 42.87 Supplying & fixing of Aerial bunch cable accessories Tension clamps(Dead end) i/c required attachment for single core cable of approved make in Air with clamp, necessary material as per specification for required size.

Elect. SOR. Page No. 106 I No. 42.64.1.3 Supplying, installing, testing and commissioning of 11/0.4 K.V. 3 Phase 50 Cycle oil immersed, naturally cooled out door type transformer connected delta on H.T. side and star on L.T. side, hand operated off load Tap changer switch above 100 kVA, oil conservator with drain valve, plug 63 KVA and above, dehydrating silica gel breather on eye level, rating and diagram plate, two earthing terminal, lifting lugs, oil level gauge, drain valve with plug, temperature not exceeding 50ºC on load, oil filling hole with plug, four unidirectional roller, arcing horns, explosion vent, terminal arrangement bushing on H.V. side and cable box on LV side, first filling of oil upto desired level and transformer installing on existing structure with all required materials arrangement as required as per IS specification. Marked ISI & 3 Star rating 42.64.1 Aluminium wound. 42.64.1.3 100 kVA

42.64.1.4 200 kVA

Elect. SOR. Page No. 101 I No. 42.57 Supplying installing, testing & commissioning D.O. fuse assembly with brass part contact for 33 or 11/0.4 KV DP Structure set of 3 Nos. with fuse barrel i/c required fuse element & other materials as per specification on existing D.P. structure as required. 42.57.1 11kV

Elect. SOR. Page No. 30 I No. 25.6.5 Supplying of ISI Marked On-Load Change over switches panel mouniting type confirming to IS : 13947 (part I & III ) with front operated 4 pole, 415 V with two earthing terminals if required. 25.6.5 200 Amps. (open - execution)

Elect. SOR. Page No. 96 I No. 42.8 Supplying and drawing guard wire/earth wire/bearer wire 13mm2 (4mm. Dia) G.I. including stringing, binding at existing insulators or brackets, jointing, jumpering, connecting & cradle etc. as required and clearing of obstacles (if any)