Military Engineer Services Tender

Excavation in trenches in soft/loose soil not exceeding 1.5 m deep and not exceeding 1.5 mtr wide and getting out including forming bottom surface to required levels/gradients/slopes for foundations/laying of cable etc. all as specified and directed.

Returning, filling in, including spreading levelling, watering and well ramming the excavated soil in layers not exceeding 25 cm thick complete all as specified and directed

Removal of surplus excavated soil to a distance not exceeding 50 Mtr distance and depositing as directed at a level not exceeding 1.5 mtr above starting point complete all as specified and directed

M & L for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as specified and directed. Note : only punned thickness shall be measured and paid.

Supplying & Laying un-reinforced pre cast flat concrete cable protection cover of class HV, type I, size 300mm x 180mm x 40mm, factory made, complete all as specified and directed.

Supply and Fixing and testing of Cable jointing kit for 11 KV (Earthed) grade cable for indoor termination heat shrink type joint complete (end joint) with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 sqmm to 185 sqmm all as specified and directed.

Supply and Fixing Cable jointing kit for 11 KV (Earthed) grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 to 185 sq mm all as specified and directed..

Demolition for cement concrete/road in ground floor and paving n. exc 15 cm thickness below or above ground level including removal of rubbish complete all as specified and directed

M&L for PCC (1:4:8) Type D-2 using 40mm graded stone aggregate as in foundation/repairs to damaged road/footpath/plinth for panels etc. including necessary formwork if required complete all as specified.

Supply & Fix 80 mm bore light grade galvanized iron tubing ISI marked including all fittings etc laid in trenches or fixed on wall protection pipe complete all as specified and directed

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including supplying and insertion of HDPE pipe of 150 mm dia suitable for 0.4 MPa working pressure all as specified and directed.

Boring of holes under road, pavement, hard standing by manual boring including supplying and insertion of HDPE pipe of 150 mm dia suitable for 0.4 MPa working pressure all as specified and directed.

Supply, installation, Commissioning and testing HV Junction box panel factory fabricated CPRI approved size not less than 1.2 x 1 x 1.2 m (LxBxH ) 3 phase 11000 Volts , AC , 50 Hz supply, Outdoor cubical type, dust and vermin proof, pedestal mounting type having suitable shape/ size canopy on top, made out of outer shell & canopy shall be 3 mm thick where as partition and inner door shall be made of 2 mm thick CRCA sheet with using the base frame shall be not less than ISMC 75 x40 mm MS angle used for fabrication of legs shall be 50x50x6 mm supports, shall be powder coated externally & internally after carrying out pre coating seven tank process comprises of degreasing, rising, derusting, rinsing, phosphating, rinsing & passivation thickness of powder coating shall be 80 micron, colour shade of powder coating shall be Siements Gray (RAL-7032) complete including locking arrangement and including PCC (1:3:6) type C2 block 150x150x300 mm deep or base channel shall be grouted in CM 1:3 and bus bar of aluminium conductor suitable shape and size for 3 phase rating of 600 amps IP-55 Protection, Including S&L 40 mm graded aggregate around the panel foundation approx 3 Sqm area, 15 mm thick and surrounding brick boundary all as specified and directed. NOTE : (a) Door shall be hinged along with locking arrangement and fixing shall be such that the doors should automatically come to closed position if not kept open with efforts. (b) Danger Notice board size 150 x 100 mm, 2 mm thick fixed on panel at both front and back side.

M & L for earthing complete with Gl electrode of size 600 mm x 600 mm x 6.00mm thick buried directly in ground vertically in pit of depth not less than 2.25 mtr below normal ground level with top edge of the earth plate not less than 1.50 mtr below normal ground level connected to Gl earth strip 32 mm X6 mm as main earthing lead by means of bolts, nuts, check nuts and washers of brass connected including gun metal or phosphorus bronze of size 75x75x25 mm drilled and screwed including 3 Nos 8 mm dia 25 mm long hexagonal head screwed all as specified including excavation and earth work and disposal of surplus soil including 40 mm dia Gl tubing light grade and necessary fitting for protection of Gl strip including laying of charcoal, dust and common salt PCC (1:3:6) type C-l( using 20 mm graded crushed stone aggregate) earth pit with 40x40x6mm mild steel angle iron frame & 40mm thick pre cast RCC cover (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) reinforced with 8mm dia TMT bars @ 75mm C/C both way with mild steel handle 12 mm dia round bars ,10mm thick plastering with cement mortar (1:4) internally and upto 150 mm below ground level externally, PGI funnel with wire mesh 20mm dia Gl pipe for watering complete all as shown on electrical plate No.3 of SSR Part -1 2009 and connected in earth test including testing completed all specified and directed.