Military Engineer Services Tender

Returning filling in including spreading , levelling watering and well ramming in layers not exceeding 25cm complete all as per specified and directed

Taking up cast iron water mains ( including all fittings) with spigot and socket ends/ Tyton joints and lead joints for the following sizes including burning out joints and recovering lead complete all as specified and directed:-

150 mm bore

200 mm bore

400 mm bore

450 mm bore

Re-fixing/relaying/Rerouting only of GI tubing for the following sizes after cleaning in same location or other location new or old position , in trenches, in walls, ceiling and floor & testing complete all as directed by Engr-in Charge Note- (i) GI Pipe obtained from Srl item No.5 shall be re-used in this item (ii). If required excavation and earth work will be measured and paid separately

150 mm bore

200 mm bore

400 mm bore

450 mm bore

Supply, laying, connecting, jointing and testing Centrifugally cast ( Spun ) Ductile iron Pressure pipe ISI Marked confirming to IS-8329-2000 ( Reaffirmed -2005 Edition 4.1 ) of following size with socket spigot ends, suitable for "Push on Joints ( Tyton Joint )" each standard working lengths supplied with rubber gaskets duly ISI marked for water supply, Class K-9 with socket with cement mortar lining inside and metallic Zinc coating with finishing layer of bituminous paint on outside the pipe with out polythylene sleeves but including "Push on Joint" supplied with ISI Marked EPDM rubber gasket conforming to IS-5382-1985 ( reaffirmed-2003 ) laid in trenches ( including all fittings) with spigot and socket ends/ Tyton joints and lead joints for the complete all as specified and directed of following sizes:-

150 mm bore

200 mm bore

400 mm bore

450 mm bore

S&F in replacement cast iron bends (any radius and angle) tappers any type (straight, bend, increasing, decreasing or double socket) Tee, pieces single branch, “ Y” junction, double branch, cross ( all socket or socket spigot) collars, caps, caps & plugs of the size upto 450mm dia complete all as specified and directed.

S&F connecting, jointing and testing of Ductile iron pipe fittings ( Specials ) heavy duty for any type ( flanged / socketed ) pipes such as, bends ( any type radius, and angle ), tapers, any type straight bend, increasing, decreasing or double socket etc. Tee pieces, ring branch, Y junction, double branch, cross ( all socket or socket and spigot ), collars, caps and plugs, adapters etc. of any size radius and length conforming to IS 9523 / 2000 specifications with external bitumen coating and internal cement mortor lining and metallic Zinc coating of size upto 150 mm bore including taking out old CI fittings complete all as per specified and directed.

M&L for cutting of bituminous Road/floor/plinth protection for laying pipe not exceeding 1.5m and 1.5m depth including refiling with excavated material and watering well ramming/compecting and making good with PCC 100 mm thick complete all as specified and directred by Engg-in-charge Note: PCC shall be measured and paid separately

M&L for PCC 1:3:6, type C-2 (using 40mm graded stone aggregates) as in filling mass concrete and making good distrubed surfaces complete all as specified and directed

M&L for water pipe line route indicator duly engravd with "PIPE LINE MES" made out of pre-cast RCC (1:1.5:3) type A1 (using 12.5mm graded stone aggregates) of size 120 cm height 15cmx15cm cross section at bottom tapered to cross section 10cmx10cm at top duly reinforced with 4 Nos 10mm dia TMT main bars and 8 mm dia TMT bar as in stirrups @ 150mm c/c complete all as specified and directed. Note:- Rate deemed included Excavation and PCC work .

Removal of detoriated valve chamber cover and providing with new MS frame work made of 25 x25 x 3mm angle iron complete and top cover made out of 3.15 mm hick MS sheet duly hinged with frame including grouting / fixing into wall chamber and painting with two coats of enamell paint over a coat of red oxide and locking arrangement , lifting hook etc complete all as specified.

Repairs to leakeage/repairs and water supply break down by using JCB/Manual arrange sufficient manpower to arrest leakeage/break down including taking down and relaying of following size complete all as specified and directed by Engineer-in-Charge (Note Earth work/PCC/CI/DI specials shall be measurerd and paid separately) :-

80 mm bore

100 mm bore

150 mm bore

200 mm bore

250 mm bore

300 mm bore

350 mm bore

400 mm bore

450 mm bore

Supply only following items complete all as directed :-

Gland rope as per sample

Rubber packing sheet 4 mm thickness

Bolts,Nuts with two washers in different length and sizes

Water proof pH pocket tester kit

Water proof TDS pocket tester kit

Chlorine test kit with samples as per sample Make: Rmco

Monoblock pressure pump 1 HP Capacity , SP,230V as per sample , Make : Kirloskar/V Guard/Texmo/CG

Monoblock Submersible pump set Open well type , Single phase, 230 V as per sample. Make: CG/Texmo/V Gurad/Kirloskar/CRI

GI Plug 15 mm dia (inner/outer thread)

DOL Starter415V, 50Hz, 3 Phase suitable for Upto to 7.5HP Motor, 415V, 3Ph as per site requirement complete all as specified and directed

Star delta starter 415V, 50Hz, 3 Phase suitable for 7.5/10HP motor, relay range 8-12Amps, contactor size 18 as per site requirement complete all as specified and directed

All as per Srl item Srl item No.15.11 here in before but 11Kw/15 HP capacity motor, 3Ph,415V, relay range 15-18 Amps, contactor size 25 asper site requirement complete all as specified and directed

All as per Srl item Srl item No.15.11 but 20 HP Capacity Motor ,3Ph,415V, relay range 15-22 Amps, contactor size 25 asper site requirement complete all as specified and directed

All as per Srl item Srl item No.15.11 but 30 HP Capacity Motor, 3Ph,415V, relay range 22-32 Amps, contactor size 32 asper site requirement complete all as specified and directed

Chain pulley block loading capacity 5 ton with chain and all accessories

GI Union 25 mm dia

S&F in replacement double action flanged Air release valve of size 80 mm dia including replacement of bolt, nuts with washers and gasket complete all as specified and directed.

Supplying, installing, testing and commissiong of self supporting totally enclosed mounted on base channel of factory made panel board CPRI approved panel builder factory fabricated made out MS sheet not less than 2.0 mm thick CRCA sheet, dust and vermin proof, hinged smoothly openable front and rear with neoprene rubber gasket, epoxy powder coated including danger plate, earth strip (25x5 mm) connecting provision -02 Nos, ventilation louvers, bottom detachable gland plate complete with suitable size zinc chromium plated nuts, bolts and washers etc panel board suitable for 3 phase 4 wire 415V, 50Hz with 200 Amps rated copper bus bar, general construction confirming to IS:8623 (Part I), including mounting on angle iron frame made using angle iron 50mmx50mmx6mm complete all as specified and as directed and shall be comprising the following including taking out LT panel board from MH pump house :-

INCOMING MCCB with micro processor, based trip 3P,415V 250 Amps 35KA - 1 No

OUT GOING MCCB with micro processor, based trip 3P,415V 63 Amps 35KA - 02 Nos

MCB SPN 40 Amps 4 Pole 16 KA - 02 Nos

Fully automatic star delta Starter 3 Ph,415 Volts, suitable for 30 HP - 02 No including accessories Make L&T/Havells conforming to IS -13947-4

Combined multifunctional Digital meter -3 Nos

LED pahse indication lamp for RYB - 9 Nos

Aluminum bus bar of 400 Amps rating 50x10 & 50 KA three phase and nutural, Panel accessories including panel designation lables, lugs, ferrules for metering/indication enclos,

Internal wiring with multi stradand copper FRLS cable for panel

Note: The rate quoated by tender also includes to fix the legs of the panel box in cement concrete M 15 (Nominal mix) using 20 mm mominal size graded crushed stone aggregate 30 cm below GL and the box will be kept nearly 45cm above GL including earth work and allied services complete. The legs of the box will be of 50cmx50cmx6mm of length 750 mm)

M&L for earthing complete with GI earth plate electrode of size 600mm x 600mm x 6 mm thick buried directly underground vertically (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate at a depth not less than 1.5m below ground level connected with and incl GI earth Strip 32x6 mm size, alternate 5 layers of charcoal (250 Kg) & salt crystal (200Kg )and top two inches layers with Back filling compound (100 Kg), in 40 mm dia GI pipe light grade by means of nuts bolts, washers and necessary earth work in any type of soil PCC (1:3:6) type C1 chamber and RCC(1:2:4) type B-1cover and watering pipe 20 mm dia medium grade with funnel complete with mesh,refiling with black cotton soil all as specified. Note:(i) Quoted rate deemend to include necessary earth work PCC chamber, RCC cover, renforcement removal of surplus soil , site clearance etc. (ii) GI GI earth Strip 32x6 mm size, GI tubing light grade 40 mm dia upto 7.5m deemed to be included the rate quoted by the contractor.(iii) Beyond 7.5 M the GI earth Strip 32x6 mm size & GI pipe light grade 40 mm dia shall be measured under the respective item of the schedule.Earthing pit display boards made out of 3 mm thick MS sheet of size 30 x 35 cm welded to 75 cm long 25 x 25 x 5 mm thick MS angle iron grouted in PCC 1 : 3 : 6 (using 20 mm graded stone aggregate) to a depth of 20 cm below GL and including applying two coats of synthetic enamel paint of approved colour over a coat of red oxide primer on all exposed steel surfaces and writing the letters on plate for showing the details :- EARTHING PIT NO : DATE OF MEASUREMENT : NEXT DUE DATE : STANDARD VALUE : VALUE OBTANED : On testing after completion from test point the desired earth resistance shall be not less than 2 ohm If the desired result is not obtained the earthing will be re done no extra cost.

M&L for GI earth strip 32mmx6mm with saddless and fixing screws drawn in GI tubing/laid intrenches/laid in duct etc above ground level complete all as specified and directed by GE

Taking down old corroded Sign boards of Frame MS pipe with MS Sheet of various sizes from the existing positions of different locations complete including making good the distrubed surfaces to match with the existing surfaces of the area in all respect all as specified and directed

Supplying, fabricating and polishing stainless steel board stand or frame of size SS heavy pipe 50 mm dia pipe work for fixing 'ACP' Sign board (Aluminium compost Panel) of size 1.6m x 1.3m , 3 mm thick with in the SS frame of size SS heavy pipe 20 mm dia pipe work and SS ball of dia not less than 50 mm on SS stand including writing details of installations/Machinery details etc with both side vinyl pasting on radium stricker letters complete all as specified an directed by Engineer-in-charge