Indian Oil Corporation Limited Tender

Laying of HDPE Pipe in trenches/ walls/ concrete structure/ panels etc. as per specifications & drawings & blowing/ laying of Owner supplied Aurmoured/Unarmoured Optical Fibre Cable in HDPE pipe, carrying out end to end testing of laid Optical fibre cables by taki ng OTDR traces and submitting the OTDR trace printouts to Site Engineer/ Engineer-in-charge. The job includes the supply and install ation of required materials such as fixing clamps, screws, tags etc. as required to complete the job in all respects as per drawings and directions of Site Engineer/ Engineer-in-charge including cost of all labour, tools & tackles, test instruments, materials etc. The job includes handing over the tested cables to the Telecom Works Contractor and providing necessary assistance/ support to the Telecom Works Contractor in commissioning of Local Area Network.

Installation of Transition Pits at building entry points as per tender specifications, drawings and directions of Engineer-in-charge / Site Engineer

Installation of wall mounted Fibre Termination Box (FMS) as per tender specifications and directions of Engineer-in-charge/ Site Eng ineer

Installation of Wall mounted Cabinet (switching closet) for housing Networking Equipment/ CCTV hardware, patch panel & accessories including power distribution boxes, MCBs/ Isolator Switches, required installation materials as per tender specifications

2 INSTRUMENTATION

As built documentation for each station covering a) Control /signalling cable layout drawings, b) Cable trench details, c) Cable m arker details, d) Earth grid layout, e) Field instrument termination details, f) Cable schedule, g) Junction box wiring details, h) Earth resistivity measurement data, i) Field panel termination details, j) Calibration data of all instruments tested as per scope. , k) OTDR Traces of the laid OFC as applicable for respective stations

3 MECHANICAL

"MLPU Installation(Motor Driven): Taking delivery of mainline pumping units having electrical motor, horizontal centrifugal pump (to be mounted on a common base plate ), Local control panel, Hydraulic coupling and other auxiliaries and accessories, grouting materi als etc from designated storage lo cation within the Pump Station, shifting and placing the equipments in the pre-constructed foun dation, carrying out levelling and g routing, aligning the equipment, assembling together of all sub-assemblies, auxiliaries, mounti ngs, fittings, interconnecting piping etc., providing assistance for carrying out trial run of motor on no load, coupling the elect rical motor with the pump, making fina l alignment, checking and testing of the complete pumping unit and completing the work in all respects in accordance with the drawin gs, manufacturer's installation instructions, technical specifications and as per the instru ction of the Site Engineer / EIC. Note: 1. The auxiliaries and mountings shall include but not limited to pipe works etc. 2. Electri cal & Instrumentation connections are not included in this item. 3. Weight of equipment is indicative only, Payment shall be done ba sed on actual weight of equipment. 4. Grouting material shall be supplied by owner. Mainline Pumping Units Installation Note: Weight of equipment is indicative only, Payment shall be done based on actual weight of equipment Approx weight of one unit is 30 Ton_A"

" Vertical Submersible type Motor Driven Water filling Pumping Unit (Q=30 KL/hr ,H= 40 MCL, Approx UnitWeight = 1 MTx1 No. = 2 MT) T aking delivery of the following pumping units with electrical motors from designated location within station premises/centralized w arehouse(details given in SCC), shifting/transporting to site, placing over Tank Nozzle, assembling together all sub-assemblies, ali gnment, grouting, levelling, checking, providing assistance for taking trial run of electrical motor on no-load, coupling the pump & motor, carrying out the trial run of the complete unit, testing, making final alignment and complete work in all respects in acc or dance with the relevant drawings, manufacturer's installation instruction, specifications and instructions of Site Engineer / EIC . Note: Weight of equipment is indicative only, Payment shall be done based on actual weight of equipment Approx weight of one unit is 1 Ton_"

"Motor Driven F/F Jockey Pump Unit Installation: Taking delivery of motor driven Fire Fighting Pumping unit from designated storage location within the pump station/centralized war ehouse(details given in SCC), shifting and placing the equipments on the pre-cons tructed foundation, levelling, grouting and aligni ng the equipment, assembling together of all sub-assemblies, auxiliaries, mountin gs, fittings, interconnecting piping etc., carrying out trial run of complete unit, making final alignment, checking and testing of the complete unit and completing the work in all re spects in accordance with the specification, drawings, manufacturer's installat ion instructions, technical specifications and as per the instruction of the Site Engineer / EIC. Note: 1. The auxiliaries and moun tings shall include but not limited to pipe works etc. 2. Electrical & Instrumentation connections are not included in this item. J ockey Pump Unit with Q-10 Kls/Hr, H-88 MCL Approx. Weight 0.5MT x 2 Nos. = 1 MT_"

"Engine Driven F/F Pumping Units Installation: Taking delivery of engine driven Fire Fighting Pumping unit from designated storage location within the pump station, shifting and placing the equipments on the pre-constructed foundation, levelling, grouting and al igning the equipment, assembling together of al l sub-assemblies, auxiliaries, mountings, fittings, interconnecting piping etc., car rying out trial run of complete unit, making fin al alignment, checking and testing of the complete unit and completing the work in all respects in accordance with the specification , drawings, manufacturer's installation instructions, technical specifications and as per the instruction of the Site Engineer / EIC . Note: 1. The auxiliaries and mountings shall include but not limited to pipe wo rks etc. 2. Electrical & Instrumentation connections are not included in this item. Fire fighting Pumping Unit with Q= 450 Kl/Hr.,H = 120 MCL, Approx. weight-7.5 MT x 3Nos. =22.5 MT_A"

"Diesel Unloading Pump unit Installation: Taking delivery of motor driven Diesel Unloading Pumping unit from designated storage loca tion within the pump station, shifting and placing the equipments on the pre-constructed foundation, levelling, grouting and align ing the equipment, assembling together of a ll sub-assemblies, auxiliaries, mountings, fittings, interconnecting piping etc., carryi ng out trial run of complete unit, making fi nal alignment, checking and testing of the complete unit and completing the work in all respects in accordance with the specificatio n, drawings, manufacturer's installation instructions, technical specifications and as per the instruction of the Site Engineer / EI C. Note: 1. The auxiliaries and mountings shall include but not limited to pipe works etc. 2. Electrical & Instrumentation connections are not included in this item. Motor Driven Diesel Unloading Pump (Q=8 KL/hr ,H= 3 0 MCL)"

"Above Ground Equipments Installation: Taking delivery and transportation of equipments from designated storage location within the pump station/Centralized warehouse loca tion within the state (Details of warehouse given in SCC) and placing on pre-constructed fou ndations, assembling together all sub-as semblies, levelling, alignment, grouting, cleaning and flushing by water, draining, checkin g, testing, dressing and making good of t he foundation and completing the work in all respects in accordance with the relevant dra wings, manufacturer's installation instruc tion, specifications and instructions of Site Engineer / EIC. Note: Weight of equipment i s indicative only, Payment shall be done based on actual weight of equipment "

Single Basket Type Strainer - 18" x 600#

"Above Ground Equipments Installation: Taking delivery and transportation of equipments from designated storage location within the pump station/Centralized warehouse loca tion within the state (Details of warehouse given in SCC) and placing on pre-constructed fou ndations, assembling together all sub-as semblies, levelling, alignment, grouting, cleaning and flushing by water, draining, checkin g, testing, dressing and making good of t he foundation and completing the work in all respects in accordance with the relevant dra wings, manufacturer's installation instruc tion, specifications and instructions of Site Engineer / EIC. Note: Weight of equipment i s indicative only, Payment shall be done based on actual weight of equipment "

Y - Type Strainer - 12" x12"- 150#

Y - Type Strainer -3" X3"X150#/ 4" x4"- 150#

"""Above ground process piping: Taking delivery & transporting of pipes from designated stock pile location /Designated godown both from outside & inside station pr emises. Taking delivery of pipe fittings, steel flanges, spiral wound metallic gaskets & fasteners from designated location within s tation premises, transporting the same to site, fabrication and erection of above ground piping in cluding cutting, edge preparation, bending, threading, lining up, welding and installing pipes and pipe fittings, flanges, elbows, equal and reducing outlet tees,conc entric/eccentric reducers, y-type strainers, drain funnels, vent pipes and tapping for instrumen ts such as pressure gauges, thermal relief valves, thermowells etc., installing above ground at all elevations connecting with equip ment nozzles, valves, vessels, in li ne instruments etc., welded and threaded pipe line of different pressure ratings, flushing pipe s by water after cleaning by compress ed air, hydrostatic testing of each section to the specified pressure, draining the water, tie -in, final cleaning-up and dispoal of wastes and surpluses including providing all inputs such as labour, material, equipments and c onsumables necessary to perform the wo rk (other than those specifically under taken by the owner in this contract) and completing t he work in all respects in accordance w ith the drawings, specifications and instructions of Site Engineer / EIC. Thickness and Grad e mentioned in the item are for referenc e only and may vary. Payment shall be based on OD"""

18" OD x 0.375"/0.438"WT APL 5L

16" OD x 0.375"/0.438"WT APL 5L

12.75" OD x 0.375" WT APL 5L

10.75" OD x 0.365" APL 5L

8.625" OD x 0.322" / 0.375" / 0.438" WT API 5L /ASTM A106/A333

6.625" OD x 0.280" ASTM A 106 Pipe/A333

4.5" OD x 0.237"WT ASTM A 106 Gr B/A333

3.5" OD x 0.216"WT ASTM A 106 Gr B /A333

2.375" OD x 0.218"WT ASTM A 106 Gr B /A333

1.315" OD x 0.179"WT ASTM A 106 Gr B /A333

"Above ground internal epoxy coated pipe for Fire Water Services: (with internal epoxy coating for repair at wending joints, Flanges & Fittings ) Taking delivery of internal epoxy coated pipes, pipe fittings, steel flanges, spiral wound metallic gaskets & fastene rs from designa ted location within station premises/Centralized warehouse within the state (as applicble) , transporting the same t o site, fabricat ion and erection of above ground piping including cutting, edge preparation, bending, threading, lining up, welding and installing p ipes and pipe fittings, flanges, elbows, equal and reducing outlet tees, concentric/eccentric reducers, y-type str ainers, drain funn els, vent pipes and tapping for instruments such as pressure gauges, thermal relief valves, thermowells etc., ins talling above groun d at all elevations connecting with equipment nozzles, valves, vessels, in line instruments etc., welded and thr eaded pipe line of d ifferent pressure ratings, flushing pipes by water after cleaning by compressed air, hydrostatic testing of eac h section to the spec ified pressure, draining the water, tie-in, final cleaning-up and disposal of wastes and surpluses including p roviding all inputs su ch as labour, material, equipments and consumables necessary to perform the work (other than those specifical ly under taken by the o wner in this contract).The scope shall also include cleaning of internal surface of pipes conforming to SSPC SP-10 of flanges, fittings and at all location where coating has been distroyed due to welding a nd repairing the internal surface by application of 2-pack cold cured Isophthalic polyster acrylic co-polymer glass flake filled /Li quid epoxy / Equivalent with coat ing of thickness 700-1000 Microns. The locations where internal coating repair is expected would be at pipe end, Flanges ,pipe fitt ings ,valve location so that the internal of pipe surface is not directly exposed to water and compl eting the work in all respects in accordance with the drawings, specifications and instructions of Site Engineer / EIC. Note:- 1) Charges for supply of pipe with i nternal coating shall be paid under separate SOR items."

18" ODx 0.375"/0.25IN WT IS3589 FE410

12.75" ODx 0.250" WT IS3589 FE410 Pipe

10.75" ODx 0.250" WT IS3589 FE410 Pipe

6.625" ODx 0.250" WT IS3589 FE410 Pipe

4.5" ODx 0.237" WT ASTM A 106 Gr B Pipe FW

3.5" OD x 0.216"WT ASTM A 106 Gr B FW

2.375" OD x 0.218"WT ASTM A 106 Gr B -FW

1.315" OD x 0.179"WT ASTM A 106 Gr B -FW

Under ground piping for Process piping (with PU/3LPE Coating): Taking delivery of bare Pipes, pipe fittings, steel flanges, spiral w ound metallic gaskets & fasteners from designated location within station premises/outside stockpile loction transporting the same t o site, fabrication and erection of underground piping including cutting, edge preparation, bending, threading, lining up and weld in g, excavating, trenching in all kind of soil to specific depths as indicated in drawings and installing pipes and all types of pi pe fittings like flanges, elbows, equal and reducing outlet tees, concentric/eccentric reducers, drain funnels, vent pipe and tappin g f or instrument such as pessure gauges, thermal relief valves, thermowells etc., underground at elevations indicated in the drawin g co nnecting with equipment nozzles, valves, vessels, in-line instruments etc.,Cleaning exposed steel surfaces of Bare Pipes, Pipe Joint s, Fittings, Flanges,equipment and valves etc. by sand blasting or with power wire brush (wherever sand blast cleaning is not possib le) free of dust, grease, mill scales etc. and applying single layer polyurethane coating(PU) using 100% solvent free elastom eric pl yurethane/ liquid epoxy, with approved materials ,Equipment etc, holiday detection of the coating, cleaning of coated pipes by water flushing after cleaning by compresed air,hydrostatic testing of each section to the specified pressure, draining the water , tie-in, back filling, restoration of site final cleaning up and disposal of water and surpluses, providing all inputs such as lab our, mater ials equipment and consumable necessary to perform the work (other than those specifically undertaken to be supplied by t he owner un der the contract) and completing the work in all respects in accordance with the drawings, specifications and instructio ns of the Si te Engineer / EIC. In case of 3LPE coated pipes, weld joints shall be PU coated.Thickness and Grade mentioned in the it em are for re ference only and may vary. Payment shall be based on OD Note:- Charges for applying single layer polyurethane coating( PU) using 100% solvent free elastomeric plyurethane/ liquid epoxy for exposed steel surfaces of Bare Pipes, Pipe Joints, Fittings, Flanges,equipme nt and valves etc shall be paid under separate SOR Item.

18" OD x 0.375"/0.438"WT APL 5L -U/G

16" OD x 0.375"/0.438"WT APL 5L -U/G

12.75" OD x 0.375" WT APL 5L -U/G

8.625" OD x 0.322" / 0.375" / 0.438" WT API 5L /ASTM A106/A333 -U/G

6.625" OD x 0.280" ASTM A 106 Gr B/A333 Pipe -U/G

4.5" OD x 0.237"WT ASTM A 106 Gr B/A333 -U/G

3.5" OD x 0.216"WT ASTM A 106 Gr B/A333 -U/G

2.375" OD x 0.218"WT ASTM A 106 Gr B/A333 -U/G

1.315" OD x 0.179"WT ASTM A 106 Gr B/A333 -U/G

Under ground piping for Fire Water Services:(with internal epoxy coating for repair at welding joints, flanges and fittings) Taking delivery of bare Pipes, pipe fittings, steel flanges, spiral wound metallic gaskets & fasteners from designated location within stat ion premises/from centralized wearhouse within the state (as applicable) transporting the same to site, fabrication and erection of underground piping including cutting, edge preparation, bending, threading, lining up and welding, excavating, trenching in all kin d of soil to specific depths as indicated in drawings and installing pipes and all types of pipe fittings like flanges, elbows, equ al and reducing outlet tees, concentric/eccentric reducers, drain funnels, vent pipe and tapping for instrument such as pessure gau ges , thermal relief valves, thermowells etc., underground at elevations indicated in the drawing connecting with equipment nozzles, val ves, vessels, in-line instruments etc., cleaning of coated pipes by water flushing after cleaning by compresed air,hydrostatic testi ng of each section to the specified pressure, draining the water, tie-in, back filling, restoration of site final cleaning up and di sposal of water and surpluses, providing all inputs such as labour, materials equipment and consumable necessary to perform t he work (other than those specifically undertaken to be supplied by the owner under the contract) .The scope shall also include cle aning of internal surface of pipes conforming to SSPC SP-10 of Flanges, fiitings and at all location where coating has been distroy ed due to welding and repairing the internal surface by application of 2-pack cold cured Isophthalic polyster acrylic co-polymer gl ass flake filled /Liquid epoxy / Equivalent with coating of thickness as per specifications. The locations where internal coating re pair is ex pected would be at pipe end, Flanges ,pipe fittings ,valve location so that the internal of pipe surface is not directly exposed to water and completing the work in all respects in accordance with the drawings, specifications and instructions of Site En gineer / EI C. Note:- 1) Charges for applying polyurethane coating(PU) for exposed steel surfaces of Bare Pipes, Pipe Joints, Fittin gs, Flanges, equipment and valves etc shall be paid under separate SOR Item. 2) Charges for supply of pipe with internal coating sha ll be paid un der separate SOR items.

18" ODx 0.375" WT IS3589 FE410 Pipe -U/G

6.625" ODx 0.250" WT IS3589 FE410 Pipe U/G

4.5" ODx 0.237" WT ASTM A 106 Gr B Pipe FW U/G

3.5" OD x 0.216"WT ASTM A 106 Gr B FW U/G

"Above ground piping for Air line: Taking delivery of pipes, pipe fittings, steel flanges, spiral wound metallic gaskets & fasteners from designated location within station premises, transporting the same to site, fabrication and erection of above ground piping i n cluding cutting, edge preparation, bending, threading, lining up, welding and installing pipes and pipe fittings, flanges, elbows, e qual and reducing outlet tees, concentric reducers, drain funnels, vent pipes and tapping for instruments such as pressure gauges , t hermal relief valves, thermowells etc., installing above ground at all elevations connecting with equipment nozzles, valves, ves sels , in line instruments etc., welded and threaded pipe line of different pressure ratings, flushing pipes by water after cleaning by c ompressed air including air cleaning prior to installation of valve by card board/ Tin blasting method, hydrostatic testing of each section to the specified pressure, draining the water, tie-in, final cleaning-up and disposal of wastes and surpluses includin g prov iding all inputs such as labour, material, equipments and consumables necessary to perform the work (other than those specifi cally u nder taken by the owner in this contract).completing the work in all respects in accordance with the drawings, specification s and in structions of Site Engineer /

3.5" ODx 0.216" WT ASTM A 106 Gr B Pipe F/A

2.375" ODx 0.218" WT ASTM A 106 Gr B Pipe F/A

1.315" ODx 0.179" WT ASTM A 106 Gr B Pipe F/A

"Under ground piping for Air piping: Taking delivery of pipes, pipe fittings, steel flanges, spiral wound metallic gaskets & fastene rs from designated location within station premises transporting the same to site, fabrication and erection of underground piping i n cluding cutting, edge preparation, bending, threading, lining up and welding, excavating, trenching in all kind of soil to specifi c depths as indicated in drawings and installing pipes and all types of pipe fittings like flanges, elbows, equal and reducing outle t tees, concentric/eccentric reducers, drain funnels, vent pipe and tapping for instrument such as pessure gauges, thermal relief va lv es, thermowells etc., underground at elevations indicated in the drawing connecting with equipment nozzles, valves, vessels, in-l ine instruments etc., cleaning the material surface by sandblast cleaning, coating and wrapping the pipes/pipe fittings with coalta r ba se tape coating material (including the supply of coating tape, precoat material etc.), holiday detection of the coating, clean ing o f coated pipes by water flushing after cleaning by compresed air prior to installation of valve, cleaning by card board/ Tin b lastin g method, hydrostatic testing of each section to the specified pressure, draining the water, tie-in, back filling, restoratio n of si te final cleaning up and disposal of water and surpluses, providing all inputs such as labour, materials equipment and consu mable ne cessary to perform the work (other than those specifically undertaken to be supplied by the owner under the contract) and c ompleting the work in all respects in accordance with the drawings, specifications and instructions of the Site Engineer / EIC."

3.5" ODx 0.237"WT ASTM A 106 Gr B F/A/ U/G

2.375" ODx 0.237"WT ASTM A 106 Gr B F/A/ U/G

1.315" ODx 0.237"WT ASTM A 106 Gr B F/A/ U/G

Valves: Taking delivery and transportation of valves of all types and pressure rating from designated location within station pr emises/ Centralized warehouse location within the state (Details of warehouse given in SCC) ,Taking delivery of from the design a ted location within station premises, transporting the same to site, erecting above ground on preconstructed foundations or un de rground including earth work in excavation and filling for under ground valves at elevations specified in the drawings, primi ng and painting of above ground valves, PU Painting of under ground portions (if applicable) including all inputs, labour, mate ria l and consumable (other than those specifically undertaken to be supplied by the owner) and completing the work in all resp ects in accordance with the drawings, manufacturer's installation instructions and specifications and instructions of the Site Engin eer / EIC.

2" ANSI 900# HOV F/F API 6D Gate Valve

Valves: Taking delivery and transportation of valves of all types and pressure rating from designated location within station pr emises/ Centralized warehouse location within the state (Details of warehouse given in SCC) ,Taking delivery of from the design a ted location within station premises, transporting the same to site, erecting above ground on preconstructed foundations or un de rground including earth work in excavation and filling for under ground valves at elevations specified in the drawings, primi ng and painting of above ground valves, PU Painting of under ground portions (if applicable) including all inputs, labour, mate ria l and consumable (other than those specifically undertaken to be supplied by the owner) and completing the work in all resp ects in accordance with the drawings, manufacturer's installation instructions and specifications and instructions of the Site Engin eer / EIC.

1" x ANSI 1500# HOV W/W API 602 Gate Valve

Valves: Taking delivery and transportation of valves of all types and pressure rating from designated location within station pr emises/ Centralized warehouse location within the state (Details of warehouse given in SCC) ,Taking delivery of from the design a ted location within station premises, transporting the same to site, erecting above ground on preconstructed foundations or un de rground including earth work in excavation and filling for under ground valves at elevations specified in the drawings, primi ng and painting of above ground valves, PU Painting of under ground portions (if applicable) including all inputs, labour, mate ria l and consumable (other than those specifically undertaken to be supplied by the owner) and completing the work in all resp ects in accordance with the drawings, manufacturer's installation instructions and specifications and instructions of the Site Engin eer / EIC.

1" x ANSI 800# HOV W/W API 602 Gate Valve

Valves: Taking delivery and transportation of valves of all types and pressure rating from designated location within station pr emises/ Centralized warehouse location within the state (Details of warehouse given in SCC) ,Taking delivery of from the design a ted location within station premises, transporting the same to site, erecting above ground on preconstructed foundations or un de rground including earth work in excavation and filling for under ground valves at elevations specified in the drawings, primi ng and painting of above ground valves, PU Painting of under ground portions (if applicable) including all inputs, labour, mate ria l and consumable (other than those specifically undertaken to be supplied by the owner) and completing the work in all resp ects in accordance with the drawings, manufacturer's installation instructions and specifications and instructions of the Site Engin eer / EIC.

2" x ANSI 1500# Sr. W/W API 602 Gate Valve HOV

Valves: Taking delivery and transportation of valves of all types and pressure rating from designated location within station pr emises/ Centralized warehouse location within the state (Details of warehouse given in SCC) ,Taking delivery of from the design a ted location within station premises, transporting the same to site, erecting above ground on preconstructed foundations or un de rground including earth work in excavation and filling for under ground valves at elevations specified in the drawings, primi ng and painting of above ground valves, PU Painting of under ground portions (if applicable) including all inputs, labour, mate ria l and consumable (other than those specifically undertaken to be supplied by the owner) and completing the work in all resp ects in accordance with the drawings, manufacturer's installation instructions and specifications and instructions of the Site Engin eer / EIC.

16" x ANSI 900# MOV F/F API 6D Ball Valve