Military Engineer Services Tender

Wall: (a) The main and partition walls shall be 60mm thick continuous line manufactured Sandwich wall Panels with facility of customized length. Insulation core: modified Polyisocyanurate foam insulation Core with an internal temperature range of -50°C to +60°C. The Panels shall be made using 0.50 mm thick color coated steel sheets on both side with 50 mm thick layer of rigid HCFC, CFC, HFC free modified Polyisocyanurate foam providing max U value of 0.36 w/m2k. Certification from NABL accredited Lab to be submitted during execution. (b) The wall panels cover width shall be minimum 1100mm with tongue and groove joint interlocking system. Panels to be laid with factory applied weather seal at side laps to provide complete weather tight performance. All materials required for the manufacture of shelter shall be new and shall comply with relevant Bureau of Indian Standard specification. Bottom & Top channel of size 30 x 65 x 30mm of 1.2 mm thick will be provided for fixing of walls panels. (c) The Polyisocyanurate foam Insulation material in the panel should have excellent fire Extinguishing characteristics when tested in accordance with BS EN 13501-1:2007+A1: 2009 with reaction to fire classification satisfying B-s1-dO and providing fire resistance minimum of 15 minutes integrity (E) when tested in accordance with ASTM E119 and should have self-ignition performance above 343 °C when tested in accordance with ASTM D1929. 2, necessary supporting test certification from NABL lab to be submitted during execution. Panel shall provide a nominal k-value of 0.018 W/mK when tested in accordance with ASTM C518 or IS 12436 and IS 16203 supporting test certification from NABL lab to be submitted during execution. (d) GI Metal Skin for Panels: 0.50mm thick hot dipped galvanized steel sheets on inner and outer side with 25 micron thick PVC guard film on the finished surface only for protection against scratches during handling and transportation. Base metal of GA skin IS-513 as per GR-120, IS-277. The pre coated GI sheet should have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finished surface and 7-8 micron primer alkyd backer on backside, which is bounded to the modified Polyisocyanurate foam. The pre coated GI sheet should conform to IS-14246-1995 with manufacturer test certificates conforming above specification.

False ceiling panel: The false ceiling shall be made up of 60mm thick continuous line manufactured hybrid core insulated fireproof sandwich ceiling Panels in min 1100mm width with facility of customized Length, Core Type modified insulation Core with an internal temperature range of -50°C to +60°C. The Panels will be made of 0.50mm thick color coated steel sheets on both side with 50 mm thick layer of rigid HCFC, CFC, HFC free modified Polyisocyanurate foam providing max U value of 0.36 w/m2k with all necessary certification to be submitted during execution. The False ceiling panels will be provided with tongue and groove joint interlocking system. All materials required for the manufacture of shelter shall be new and shall comply with relevant Bureau of Indian Standard specification. The false ceiling panels will be provided with tongue and groove or lip locking joint for interlocking. False ceiling will be supported with the help of inverted CRCA Tee Section 50 x 50 x 6 mm thick (4.40 Kg/Rm) and L- section of 50 x 50 x 5mm thick (3.80 Kg/Rm) fixed appropriately to the Truss as specified and directed.

Floor Panels: The hybrid core insulated fireproof floor panels of the shelter & wind breaker room shall be of 60 mm thick. The panels shall be made using 0.60 PPGI skin ( RAL 9002 /9003) at the bottom and 40 mm CFC Free 44 kg/cm3 bulk density (+/- 2 kg/cm3 ) panel Insulation in between along with 18 mm thick BWR grade plywood on top. The Floor panels shall be joined using cam locks & tongue and groove arrangement produced on discontinuous panel production line. The floor top will be provided with 2 mm thick aluminum chequered profile fixed with suitable counter sunk screws. Toilet portion Flooring: S&F coloured Non skid ceramic tile of size 300x300mm of 7-8 mm thick over 15 mm thick screed bed of cement mortar 1:6 over sub base of 75mm thick PCC 1:4:8 Type D-2 over 100mm thick hard core complete all as specified and directed.

Flashing:- Suitable flashing with 0.6mm thick pre-coated sheet of matching color with panels will be provided at all joints between roof and wall corners.

Roof: 0.60 mm thick PPGI sheet approved color fixed with self-tapping screws over steel purlins. Steel sheets shall be laid with corrugations over lap at sides and 15 cm end overlap or as per manufacture's instruction. Pre painted (matching with roof tint) wind tie of size 40 X 5mm flat iron shall be provided at lower and upper horizontal end of each pitch for protection against wind. The Profile of Galvalume sheet on roof will project 400mm outside the ends of front and rear side and 300mm at the both gable ends. In addition to self-tapping screws shall also be fixed for roof sheeting. The sheets shall be as per IS. Ridge Cover 0.60 mm thick pre-painted corrugated/plain sheet of approved color matching with the roof sheet of size & design, 3.0 m long and 900 mm wide will be provided. PPGI sheet is to be fixed on top junction of the roof using suitable self-tapping screws over steel purlins. Installing foam closers between Ridge cover and Roof sheet to avoid the entry of snow inside the shelter. No gap should be there in the roof design for allowing the entrance of snow inside the roof from ridge and roof sheet. Wind Breaker Roof:- The wind breaker cabin roof shall be made up of 50mm thick alongwith minimum 28 mm trapezoidal shape Panels. The Panels will be made of 0.6 mm thick PPGI on both sides and a layer of rigid CFC free polyurethane foam of density 44 kg/Cum +/-2kg/ cum as Insulation. The roof PUF panels have one ridge / end lap overlapping of minimum 150 mm on the sides and will be fixed on to the roof steel structure using STSD (Self tapping self drilling) screws.

Ventilator:- 04 Nos-Powder coated aluminum three track sliding window of size 1000 x 600 mm with glass and stainless steel fly proof mesh with aluminum grill shall be provided (02 nos of glass shutter, 01 Nos wire mesh shutter). Outer frame shall be made of 1.6mm thick weight not less than 0.710 kg/m and shutter frame shall be made of size 44 x 44 x 1.6mm thick, weight not less than 0.670 kg/m and clip shall be made of size 21 x 15.4 x 1.22mm, weight not less than 0.18 kg/m. Mullion shall be made of size 59 x 38 x 1.6mm thick, weight not less than 0.85 Kg/M. Grill frame shall be made of 42.4 x 10 x 12mm thick, weight not less than 0.325 Kg/m and including 5mm thick glass necessary joining cleats, glazing chips, rubber packing. Aluminum grill having 10mm dia weight not less than 0.54 Kg/Sqm along to with aluminum fly proof mesh having 1mm aperture of wire mesh 24 gauges shall be fixed aluminum shutter. All the material used for aluminum frame work should conform to IS-733- 1983, IS-737-1986 or IS-1285- 2002 Make: Tata/Jindal/Hidalco as shown in drg.

Window:- 06 Nos-Powder coated aluminum three track sliding window of size 1000 x 1000 mm with glass and stainless steel fly proof mesh with aluminum grill shall be provided (02 no’s of glass shutter, 01 Nos wire mesh shutter). Outer frame shall be made of 1.6mm thick weight not less than 0.710 kg/m and shutter frame shall be made of size 44 x 44 x 1.6mm thick, weight not less than 0.670 kg/m and clip shall be made of size 21 x 15.4 x 1.22mm, weight not less than 0.18 kg/m. Mullion shall be made of size 59 x 38 x 1.6mm thick, weight not less than 0.85 Kg/M. Grill frame shall be made of 42.4 x 10 x 12mm thick, weight not less than 0.325 Kg/m and including 5mm thick glass necessary joining cleats, glazing chips, rubber packing. Aluminum grill having 10mm dia weight not less than 0.54 Kg/Sqm along to with aluminum fly proof mesh having 1mm aperture of wire mesh 24 gauges shall be fixed aluminum shutter. All the material used for aluminum frame work shall conform to IS 733-1989, IS 737, 1986 or IS 1285-2002 (as amended upto date).

Main Doors. 02 Nos of door shall be provided for all shelters having size 995mm x 2135mm made of powder coated aluminum frame will be provided as per drawing. The door shall be of GI metal skin reinforced with hybrid core insulated panel 50mm thick of same color (specification mentioned above for the walls panel). The internal shutter shall be hanged with 03 pieces heavy duty hinges. 2 Nos of aluminum AL drop of 250 mm and Aluminum tower bolts of 200 mm size from inside and 2 Nos D type handles shall be provided in each shutter. 1 Nos Canopy Rain/sun shed of 0.60 mm thick PPGI sheet of size 1000 mm x 450 mm using angle iron frame of size 35 x 35 x 3 mm duly painted over with red oxide primer. All the material used for aluminum frame work should conform to IS-733-1983, IS-737-1986 or IS- 1285-2002. Internal Doors. 02 Nos of door will be provided for all internal partition having size 750mm x 2100mm made of PVC material. Frames made with Aluminum section confirming IS-733-1983, IS-737-1986 or IS- 1285-2002 and relevant IS Codal provision.

Wooden partition: Cubical needs to be constructed for ease of Working in office using plywood with the height of 1.5m and at a gap n exe 2.5m as specified and directed by the Engr-in-charge.

Construction of small ventilated puff structure of appropriate size with a door to keep battery for solar panels all as specified and directed as on ground by the Engr-in-charge

S/F curtain rod decorated type chromium plated 1200mm long 25mm dia for doors and openings including brackets and domes/funnel complete as directed by Engr-in-Charge

Wash basins, Vitreous China (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe.

Soap dish, any type, fixed to plugs with chromium plated brass screws

Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including waste pipes including flushing cistern 10 Ltr

Vitreous China urinals, half stall urinal (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) including all waste pipes

Towel Ring Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms)

Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm- 125gms).

Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed but fancy type Size: 15 mm

Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed but fancy type 15mm bore dia

S/F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms)

SEWAGE AND DRAINAGE SYSTEM -S&F PVC (SWR) pipe of size 110/75 mm with proper connected bends/joints/traps to be provided for proper drainage and sewage complete all as specified and directed. Note :- (a) S&F PVC (SWR) of size 75mm Vent pipe with vent cowl complete all as specified. (b) Proper connection to nearby septic tank/soakage well for proper dranout of waste water complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified.

S/F Puff tank capacity 500Ltr and subsequent plumbing

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. 16mm and 20 mm as specified and directed by Engr-in-charge

Lagging to pipes used in internal water supply or plumbing all round with, 25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 20mm

600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Stop valves, cast copper alloy , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type, chromium plated with long shank and cup

S/F Puff tank capacity 500Ltr and subsequent plumbing includig staging at appropriate ht as specified by Engr-in-charge.

S&F of Sandwich puff panel 80 mm For Supply of puff panels manufactured in Continuous Production Line using pre-painted galvanized sheet density : 42 kg.Top and bottom sheet thickness : 0.50mm colour coating Rmp Yield Strength : 240 Mpa Coating Mass : 120 GSM width 1.12M

M & L for 75 mm thick PCC 1:3:6 type C-2 as in plinth protection finished even and fair using extra cement laying in bays as directed

Note:- Anything missed out above but required as per arch line plan for construction of building so as to meet its functional requirement shall be deemed to be included in quoted rate.

Internal Electrification Supply and fixing, sheet metal enclosure MCB distribution board SPN 240 volts ,8 way with IP-43 IK-09 protection double door complete with 200A rated bus bar and neutral link/earth flush in wall , complete all as specified and as directed

Supply and fix, MCB, SPN, 40Amps, 240 volts, 10KA, 'C' type, ISI marked complete all as specified and directed.

Supply and fix, MCB, SP, 6-32Amps, 240volts, 10KA, 'C' type, ISI marked, complete all as specified and directed.

M&L for point wiring for one light/fan/bell point controlled by one switch one way in and including PVC casing and caping including accessories, ISI marked as per site requirement using FRLS PVC unsheated multi stranded copper conductor unsheathed cable 1.5Sqmm single core for one light/fan/bell point controlled by one switch including 3mm thick plastic laminated sheet cover over PVC box for each earth continuity, insulated PVC unsheathed (green colour) 1.5 Sqmm copper earth wire connected to common earth dolly using complete all as specified and directed by Engineer-in-Charge. Note:- Wiring shall be done by using proper colour coding.

All as per Serial item No. 2.03 here-in-before but for 5 amp socket outlet on independent board.

All as per Serial item No. 2.03 here-in-before but for 5 amp socket outlet on same board.

All as per Serial item No. 2.03 here-in-before but for 15 amp independent socket outlet using 4 sqmm single core copper wire for phase, neutral and earth complete all as specified and directed.

Supply and fixing, switch piano, flush type, single pole, one way, 5Amps, 230V, complete all as specified and as directed.

S&F Switch Bell push, flush type, 5 amp ISI marked 230 volts complete all as specified and as directed.

Supply and fix, socket outlet, flush type, 2-in-1 3 pin, 6Amps & 16Amps, 230volts, complete all as specified and as directed.

Supply and fix, socket outlet, flush type, 2-in-1 3 pin, 6Amps , 230volts, complete all as specified and as directed.

Supply and fix, switch socket combination, flush type, 2-in-1 3 pin, 6Amps , 230volts, complete all as specified and as directed.

Supply and fixing, switch piano, flush type, single pole, one way, 15Amps,230V, complete all as specified and as directed.

Supply and fix, ceiling rose Bakelite white/black coloured of size 50x65mm three terminals, complete all as specified and as directed.

Supply and fix, holder insulated body with back plate including 9W LED lamp, complete all as specified and as directed.

Supply and fix, LED light fitting 1x20W, 220V, AC decorative box type with driver ISI marked, including LED tube rod connecting up with three core flexible copper wire of suitable size from ceiling rose,complete all as specified and as directed. Make:- Bajaj Cat Part No. BCLAB/BCLSB 20W or equivalent of Havells/Philips/Crompton

S&F ENDURA Slim Pro Plus PANEL 36W LED 5700K LED fitting with LED prismatic optical modular luminaries suitable for Recesses mounting complete with HF electronic driver complete all as specified and as directed

Supply and fix, energy saving new generation endura rugby neo 10W LED IP65 bulk head luminaire with opal diffuser, etc complete with all accessories prewired electrically connected, complete all as specified and as directed.

Supply and fix, exhaust fan plastic body, 250mm (12") sweep, single phase, 230V, 50Hz AC, 1400RPM, energy saving, heavy duty totally enclosed, heavy duty motor with die-cast aluminium rotor mounted on two ball bearings complete with louvers and shutters including cutting hole for fixing exhaust fan to puf panel, connecting electrically using 3 core 0.75Sqmm PVC insulated flexible copper conductor cable overall sheathed all as required at site, complete all as specified and as directed.

Material and labour for Sub Main Wiring with Two run single core 6Sqmm (nominal area) multi stranded copper conductor FRLS PVC insulated and unsheathed 1100volts grade colour code cables, drawn on surface in and including PVC nedium duty conduit of size 20mm dia bore medium grade, including standard fittings such as Tees, junction, bends etc., with and including One run of continuous multi stranded copper conductor 6Sqmm (nominal area) FRLS PVC insulated and unsheathed 1100volts grade colour code cable for earth continuity , complete all as specified and directed. Note:- Two run of 6Sqmm + One run of 6Sqmm for earth wire shall be measured as one RM.

Material and labour for Earthing complete with GI earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (earth pit not less than 2.5 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, earth pit surrounded by 15 cm thick and packed layers of charcoal, dust and common salt, including GI wire 4 mm dia as earth lead fixed by means of nuts, bolts, check nuts and washers etc and other end connected to the test point including 15 mm dia light grade GI protection pipe and watering pipe 20 mm dia medium grade with funnel and wire mess including necessary earth work, PCC earth pit chamber in PCC 1:2:4 using 20 mm graded stone aggregate with precast RCC pit cover 80 mm thick etc including dismantling old earthing, complete all as directed and specified.

Supply and fixing LED type solar street light 25 Watt with auto on/off , dusk detection 8 V down deflection complete with all accessories in built. Solar street light should consist of built in mono crystalline panel of minimum capacity 38 watt,12.8 V lithium Ferro phosphate (LiFEPO4) battery of minimum 18 Ah (BIS certified) with inbuilt MPPT charge controller with efficiency more than 90% and PIR sensor with colour temp 6000-6500K. The battery should have 02 days autonomy with dimming profile . The street light should have ingress protection IP 65 and impact protection IK 06, complete all as directed and specified.. Make: Bajaj cat part no SUNSOKO AIO-BSZSL 25 W LED or equivalent of Crompton /Havells/Wipro/Philips. Note : Minimum 2 years warrantee and test certificate from manufacturer shall be submitted.

Lightening Protection Material and labour for aluminium strip of 25x3.15mm complete with saddles with screws/ washers etc. over Elapp epoxy electrical insulator (red) on wall and roof of building complete all as specified and as directed by Engineer-in-Charge. Note: Aluminium strip should not touch building or roof at any place

Material and labour for air termination, single pointed aluminium rod 12mm dia and 300mm long and Elapp epoxy electrical insulator (red) screwed properly on aluminium strip complete all as specified and directed by Engineer-in-Charge..

Material and labour for test point terminal block made out of gun metal or phosphorus bronze size 75 x 75 x 25mm drilled and screwed including 3 Nos 8mm dia 25 mm long hax. head screw complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Earthing complete with GI earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (earth pit not less than 2.5 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, earth pit surrounded by 15 cm thick and packed layers of charcoal, dust and common salt, including GI strip 32 x 6 as earth lead fixed by means of nuts, bolts, check nuts and washers etc and other end connected to the test point including 40 mm dia light grade GI protection pipe and watering pipe 20 mm dia medium grade with funnel and wire mess including necessary earth work, PCC earth pit chamber in PCC 1:2:4 using 20 mm graded stone aggregate with precast RCC pit cover 80 mm thick etc all as shown in Electrical Plate No. 3 of SSR Part 1, complete all as directed and specified.

Supply and laying GI water tubing medium grade 80mm dia (ISI marked) with and including all fittings (such as bends, elbows, T, short pieces, connectors back nut, diminishing pieces, caps plug and union etc) laid in trenches, fixed complete to walls and ceilings or laid in floors complete all as specified and directed. Note:- Excavation and earth work included in quoted rates

Material and labour, Plain Cement Concrete (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in foundations, coping, Panel foundation etc, the top surface shall be finished smooth by using extra cement including necessary form work complete all as directed and specified.

Solar Power Plant Supply, installation, testing and commissioning of roof top solar power plant on Grid type of capacity 4KW/5KVA @ 0.8 Power factor 48/96 Volts, Sine wave, 50 Hz, 230V suitable for minimum 1 hrs backup including solar panels, solar chargers, solar converters, battery bank suitable for High altitude area for smart management of solar power, grid supply to deliver uninterrupted power to light/fan points all as specified below all as per manufacture guidelines all as directed:- (a) Solar battery Lithium Ferro Phosphate Li FePO 4 battery suitable for high altitude area of Leh of capacity 100 AH, 12V power/battery pack. Power pack comprising of 04 batteries shall be BIS marked and test certificate is mandatory. The batteries shall be as per original supplier of complete solar system. (b) Solar Charge controller in built in pcu MPPT type capacity 70 Amps as recommended by manufacturer. (c) Grid input voltage - single phase, 100V-280V 50 Hz (d) UPS/converter, 230Vac, Sine wave, 50 Hz THD3% with 48/96V de rated. (e) The complete system shall be of IP20 protection and shall be suitable to work at high altitude area of Leh. (f) Suitable protection against over voltage, short circuit etc shall be provided. (g) Solar mono crystalline 550 watt power DCR module made in India as per manufacturer guidelines - 10 Nos Note:- (a) The contractor may plan the work in such a way that the UPS charge controller, related protection arrangement etc may be enclosed in a compact container as per standard manufacturing. (b) The system shall be such that while handling the load, the solar power shall be given priority over normal grid supply. In case solar supply fails, system shall be automatically switched over to grid electric supply with minimum inconvience to user (c) The make of solar system shall be luminous/waaree/Tata power solar/ADANI solar as approved by GE. (d) All equipment of solar system shall be as per BIS specifications/ meeting IEC standard (e) Warranty for solar system- minimum 5yrs panel warranty - minimum 25 years, Batteries warranty -minimum 05 years. (f) Anything missed out for running of solar panel /minimum for smooth functioning of solar system shall deemed to be included in the quoted rates. (g) Arrangement for fixing on roof including iron and concrete work is included in quoted rates. The rate shall be inclusive of making good of the surface.

Supply and fixing, sheet metal enclosure MCB distribution board SPN 240 volts ,12 way with IP-43 IK-09 protection double door complete with 200A rated bus bar and neutral link/earth flush in wall , complete all as specified and as directed

External Water Supply Excavation in trenches in hard/dense soil not exceeding 1.5 metre wide and not exceeding 1.5M in depth for laying of GI pipe/cable and getting out of excavated material complete all as specified and directed by Engineer-in-Charge

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed by Engineer-in-Charge

Removal of surplus excavated soil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5metre above the starting point, complete all as specified and directed.

Supply and laying GI water tubing medium grade 20mm dia (ISI marked) with and including all fittings (such as bends, elbows, T, short pieces, connectors back nut, diminishing pieces, caps plug and union etc) laid in trenches, fixed complete to walls and ceilings or laid in floors complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid seperately and all GI pipes shall be laid below frost line at Leh.

Supply and laying GI water tubing medium grade 25mm dia (ISI marked) with and including all fittings (such as bends, elbows, T, short pieces, connectors back nut, diminishing pieces, caps plug and union etc) laid in trenches, fixed complete to walls and ceilings or laid in floors complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid seperately and all GI pipes shall be laid below frost line at Leh.

Supply and laying GI water tubing medium grade 50mm dia (ISI marked) with and including all fittings (such as bends, elbows, T, short pieces, connectors back nut, diminishing pieces, caps plug and union etc) laid in trenches, fixed complete to walls and ceilings or laid in floors complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid seperately and all GI pipes shall be laid below frost line at Leh.

Supply and fixing stop valves (ISI marked) , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 25 mm dia bore complete all as specified and directed.

Supply and fixing stop valves (ISI marked) , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 20 mm dia bore complete all as specified and directed.

Supply and fixing gunmetal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 50 mm of size complete all as specified and directed.

M &L for Random rubble un-coursed stone masonry in cement mortar 1:6 valve pit of internal size (150cm x 150cm x 150 cm), with 38 Cm wall thickness, 50mm thick coping with PCC 1:2:4 type B-1 (using 20mm graded stone aggregate), plastering internally with 15mm thick in Cement mortar 1:6 and flush pointing externally in the same mortar as the work proceeds including excavation and including angle iron frame made of 50x50x5 mm angle iron with MS sheet cover of size 3.15 mm thick of size with provision of locking arrangement including earth work and disposal of surplus soil to a distance not exc 50 mtr and depositing complete all as directed by Engr-in-Charge

M& L for cutting of pipe upto 80mm dia for insertion of new pipe complete with welding, brazing complete all as specified and directed by Eng in charge

External Electric Supply Material and labour, sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

Supplying and laying, factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, ISI marked for protection of LT cable , complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 95 Sqmm 3.5 core aluminum conductor 1100volts grade underground cable ISI marked including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc complete all as specified and as directed. Note(s): (i) Excavation & earth work, sand cushioning and PCC cover for protection of cable shall be measured and paid separately.

All as per serial Item No. 7.03 here-in-before but cross sectional area 70 Sqmm 3.5 core .

All as per serial Item No. 7.03 here-in-before but cross sectional area 16 Sqmm 2 core .

Supply installation, test and commissioning of Outdoor type LT Panel Board cubical type outdoor Confirming to Relevant IS , floor mounted factory fabricated made out of 3.15 mm thick CRCA sheet CPRI approved dust proof/vermin proof & suitable size to accommodate all accessories/fittings, compartmentalized in construction to accommodate incoming and o Outgoing MCCB, MCB and TPN copper bus bars of rating not less 1.5 times the rated cap of incomer Outgoing MCCB / ACB and outgoing feeder. The TPN bus bars shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on DMC/epoxy insulator of size not less than 50 x 50 mm conical type at an interval of not more than 500 mm through out the length of the TPN bus bar . The incoming as well as outgoing MCCBs shall have copper extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. The extension links shall be supported on DMC / Epoxy insulators having provision for termination of incoming and out going cables. All extension links /interconnection shall be insulated with heat shrinkable colour coaded sleeves. The cubicle shall have a bottom channel of size as designed by the manufacturer . A detachable predrilled gland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size with glands. The above panel shall be front and back openable lockable /openable by key from both side and shall have louvers and air vent gasket for natural flow of air. 3 mm XLPE adhesive type gasket shall be used to make panel weather, dust and vermin proof with IP65 degree of protection , complete as specified and consisting the following switchgears and accessories: (i) Bus bar made up of copper with heat shrinkable sleeves with colour code supported on epoxy resin based insulators, 4 strips of suitable length for current rating 250 amps. (ii) Main Incoming MCCB four pole 415 V AC, current rating 160 amps adjustable type with breaking capacity 25 KA at 415V with thermal magnetic release-01 Nos (iii) Outgoing MCCB 415 V AC, current rating 63 amps,breaking cap 16 KA at 415 V AC = 09 Nos (iv) Digital Ammeters 96x96 mm with suitable CT ratio (v) Phase Indiactor lamp -01 Set (vi) Digital Volt meter (vii) PCC 1:3:6type C-2 using 40mm graded stone aggregate for grounting 04 legs of LT Panel 45 cm deep below GL all as specified and directed by Engineer in charge

Supply, installation, test and commissioning of Outdoor type LT Panel Board cubical type outdoor Confirming to Relevant IS , floor mounted factory fabricated made out of 3.15 mm thick CRCA sheet CPRI approved dust proof/vermin proof & suitable size to accommodate all accessories/fittings, compartmentalized in construction to accommodate incoming and o Outgoing MCCB, MCB and TPN copper bus bars of rating not less 1.5 times the rated cap of incomer Outgoing MCCB / ACB and outgoing feeder. The TPN bus bars shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on DMC/epoxy insulator of size not less than 50 x 50 mm conical type at an interval of not more than 500 mm through out the length of the TPN bus bar . The incoming as well as outgoing MCCBs shall have copper extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. The extension links shall be supported on DMC / Epoxy insulators having provision for termination of incoming and out going cables. All extension links /interconnection shall be insulated with heat shrinkable colour coaded sleeves. The cubicle shall have a bottom channel of size as designed by the manufacturer . A detachable predrilled gland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size with glands. The above panel shall be front and back openable lockable /openable by key from both side and shall have louvers and air vent gasket for natural flow of air.3 mm XLPE adhesive type gasket shall be used to make panel weather, dust and vermin proof with IP65 degree of protection , complete as specified and consisting the following switchgears and accessories: (i) Bus bar made of copper strip with heat shrinkable sleeves with colour code supported on epoxy resin based insulators, 4 strips of suitable length for current rating 400 amps. (ii) Main Incoming MCCB four pole 415 V AC, current rating 250 amps with breaking capacity 25 KA at 415V with thermal magnetic release -01 Nos (iii) Main Incoming MCCB four pole 415 V AC, current rating 160 amps with breaking capacity 25 KA at 415V with thermal magnetic release -03 Nos (iv) Digital Ammeters 96x96 mm with suitable CT ratio (v) Phase Indiactor lamp -01 Set (vi) Digital Volt meter (vii) PCC 1:3:6type C-2 using 40mm graded stone aggregate for grounting 04 legs of LT Panel 45 cm deep below GL all as specified and directed by Engineer in charge