Kerala Small Industries Development Corporation Limited Tender

Providing and fixing Panelled or Panneled and glazed shutters for doors windows and clerestory windows, 30 mm thick shutters including ISI marked MS pressed Butt hinges bright finished of required size with necessary screws excluding panelling which will be paid seperately all complete as per the direction of engineer in charge. using Anjili wood

Solid Block masonary using Precast solid blocks (factory made) of size 40X20X15 cm for superstructure upto floor 2 level with thickness 15cm in: cm 1:6 ( 1 cement : 6 coarse sand etc complete)

12mm cement plaster of mix 1:4 ( 1 cement: 4 fine sand)

Smooth finishing of the exposed surface of RCC work with 6 mm thick cement mortar 1:3 1 cment: 3 fine sand)

15 cm Cement Plaster on the rough side of single of half brick wall of mi 1:4 ( 1 cement : 4 fine sand)

Providing in laying in position cement concrete of specified grade excluding cost of centering and shuttering - Ratio 1: 2:4 ,1 cement : 2 coarse sand : 4 graded stone agreegate 20 mm nominal size

Providing and laying Vertified floor tiles in different sizes iwth water absorbtion less than 0.08% and conforming to IS : 15622, of approved make in all colours and shades , layed on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc complete. sie of tile 600 X 600 mm.

Providing and fixing First quality Ceramic glazed floor Tiles conforming to IS : 15622 of approved make in all colours shades ecept burgundy, bottle green, black of any size as approved by engineer in charge in skirting, risiers of steps and dados over 12mm thick bed of cement mortar 1:3 ( 1 cement; 3 coarse sand) and jointing with grey cement slurry at@ 3.3kg per sq m including pointing in white cement mixed with pigment of mathching shade complete

Providing and fixing First quality Ceramic glazed Wall Tiles conforming to IS : 15622 of approved make in all colours shades ecept burgundy, bottle green, black of any size as approved by engineer in charge in skirting, risiers of steps and dados over 12mm thick bed of cement mortar 1:3 ( 1 cement; 3 coarse sand) and jointing with grey cement slurry at@ 3.3kg per sq m including pointing in white cement mixed with pigment of mathching shade complete

Providing in laying in position specified grade of Reinforsed cement concrete excluding cost of centering and shuttering finishing and reinforsement / all work upto plinth level - Ratio 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone agreegate 20 mm nominal size)

Centering and Shuttering including strutting etc and removal of form for lintels, beams, plinth beams griders, bressumers and candilevers

Steel Reinforcement for RCC work: including straightning cutting bending , placing in position and binding all complete upto plinth level. Thermo mechanically treated bars of grade Fe 500 D or more

Providing and fixing Aluminium Work for doors, windows , ventilators and partitions with etruded built up standards tubular section / appropriate section and other sections of approved make conforming to IS 733 and IS 1285, fixing with dash fastners of required dia and size, including necessary filling up the gaps at junctions ie at top, bttom and sides with required EPDM rubber / neoprene gasket etc. Aluminium section shall be smooth rust free straight , mitred and jointed mechanically where ever required including cleat angles , aluminium snap beading for glazing / panelling, CP brass / stainless steel screws, all complete as per Architechtural drawings and the directions of Engineer in charge. For shutters of doors , windows and Ventilators including providing and fixing hinges / pivots and making provisions for fiing of fittings where ever required including the cost of EPDM rubber/ neoprene gaskets required. Providing and fiing 12mm thick prelaminated particle board flat pressed 3 layer or graded wood particle board conforming to IS 12823 grade 1 type 2 in panelling fixed in aluminium doors windows shutters and partition frames with CP brass / stainless steel screws etc complete as per architechtural drawings and directions of engineer in charge.

Providing and Fixing MS Grills of required patterns in frames of windows etc with MS flats Square or Round Bars etc including Priming coat with Approved steel primer all complete fixed to openings with rawl plug srews etc

White washing with lime to give an even shade 3 or more coats

Providing and applying white cement based putty of avg thickness 1 mm of approved brand and manufacturer over the plastered wall surface to prepare the surface even and smooth complete

Finishing with Delux multi surface paint system for interiors and exteriors using primer as per manufacturers specification 2 or more coats applied on wall@ 1.255lyr per 10 sqm over and including one coat of special primer applied a@0.75 ltr per 10 Sqm

Designing Fabricating testing installing and fixing in position curtain wall with aluminium composite panel cladding with open grover for linear as well as curvilinear portion of the building for all height and all levels etc .

Providing and Fixing factor made uPVC door of size 80 X 210 cm of which uPVC door frames made of etruded section having a overall dimention as below.( Tolerance +- 1mm) , corners of the door frame to be jointed with Galvanised brackets and stainless steel screws , jointsmitre and plastic welded . Providing and fixing to existing door frames 24 mm thick factory made PVC door shutters

Providing and fiing stailess steel grade 304 railing made of hollow tubes channels plates round pipes etc including welding grinding , buffing, polishing and making curvature where ever requird and fitting the same with necesary SS nuts and bolts complete

Electrical work

Plumbing work