Southern Railway Tender

Providing health faucet near the EWC similar to model No. F8030401AB or similar 2 approved 1.2m branded hose pipe with built in pressure regulating nozzle to adjust flow rate for hygienic cleaning. Rate includes all fittings, fixing to line and commissioning for functionally without any damage to existing wall, pipe or fittings as directed by Engineer in charge

Supply and installation of curtains of approved quality comprising of face fabric lining 3 track channel holders hooks and so on including all labour , materials lift and lead ,transportation and charges for tools equipments etc...as directed by engineer in charge. as directed by Engineer in charge

Blinds:- Supplying and fixing Semi Sheer polyester Roller blinds including all fittings as per selection and design as directed by Engineer in charge

Signage and Logo - Making and fixing 550mm dia logo in glossy brass finish and lettering below the same finish including all cost of materials and labour charges. as directed by Engineer in charge

Providing, supplying and placing of High Back Chair. SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and molded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D). BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns)tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm (W) x 70.5 cm (H).HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be molded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one piece armrests should be injection molded from black 6 Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features:• 360° revolving type.• 17° ±2° maximum tilt on pivot at centre • Upright position locking. Tilt tension adjustment. .PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm.TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon. Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm.Height - min 99.5 to max 110.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth- 76.3cm.This product should be certified by Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of Mid Back Chair. SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and molded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D).BACK ASSEMBLY: The back assembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm (W) x 60.5 cm (H).HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be molded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection molded from black 7 Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features:• 360° revolving type.• 17° ±2° maximum tilt on pivot at centre • Upright position locking. • Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm.TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection molded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection molded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection molded in black nylon. Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm.Height - min 89.5 to max 100.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth- 76.3 cm. This product should be certified by Indoor Advantage GOLD & GREEN PRO. (rate as per quote attached)

Overall Dimensions of Storage Unit shall be 1200mm(W)x450mm(D)x711mm(H). The top shall be Metal top (1 mm add in unit height ) . The Rigid Knock Down Construction , Back , Sides and Door shall be made from 0.7 mm high yield strength CRCA ,rest in 0.8 mm CRCA . CRCA - 'D' Grade as per IS-513 . Sliding door arrangement shall have sliding door with top hanging arrangement to prevent derailment . Each door shall be provided with 2 plastic roller having steel ball bearing for 8 smooth movement of door & less noise . Locking shall be 5 lever cam lock for safe locking . Handle shall be plastic flush & recessed handle . Shelving shall have Height wise adjustable shelf mounting . Uniformly Distributed Load Capacity of the shelf is 40 Kg maximum . Storage Unit shall have 2 no. of adjustable half shelves. Accessories optional shall be cradle with pipes for hanging Godrej instadex files . Leveler shall be screw type leveler with hex plastic base and overall finish shall be epoxy polyester coated to the thickness of 50 microns . For Storage Unit A4 size box file can be stored vertically on one shelf and clear space above second shelf is 220 mm

Work Station RECTA 1200 x 600 . Panel Height - 1200mm - The system is modular tile based open plan office system. It comprises of two types of panels as per thickness 52.4mm. The 52.4 mm panel has more elaborate and flexible construction offering various functional and decorative finishes as well as cable management capacity. The top trims and end trims for 52.4 mm shall be made from aluminum extrusion having material AL96063-T6. All kinds of extrusions for 52.4 mm shall have average wall thickness of 1.2 mm & having finish of powder coating. Top trim in 52.4mm thick panel shall be press fitted on the horizontal extrusion it shall be slide fitted with the 9 help of top trim connector made from PP copolymer 3530 grade. End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513. These uprights and horizontals shall be made of aluminum extrusion having material AL96063-T6 & have average wall thickness of 1.2 mm & powder coated with epoxy-polyester powder. BOTTOM FAME ASSEMBLY:Fabricated bottom frame for 52.4mm shall comprise of LChannels made of 2mm thick CRCA steel (IS:513), formed plates of 3mm thick HR steel (IS:2062) & ERW steel tube of size 35x15x1.6mm in oval cross section (IS:7138) welded together. This shall be coated with average 50 to 60 micron thickness of epoxy powder coating. This shall be bolted to the uprights with M6 screws. Tiles: Combination of top tiles are fabric tackable/white board. Bottom tiles - Plain metal. Fabric tackable tiles shall be upholstered metal tiles in 0.6mm thick G.I. grade O as per IS: 277, with P.E. foam in the tile for tackablity. The fabric shall be upholstered with adhesives. White board tiles shall be made of 8.0 mm thick particle board conforming to IS: 12823 laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and will be having all its edges with minimum 0.5 mm thick PVC edging. Plain Metal tiles shall be powder coated metal tiles in 0.8 mm thick M.S. CRCA Grade D as per IS: 513.INTERMEDIATE BLOCKS A block for 52.4mm panel's thickness shall comprise of 38mm thick paper honeycomb with 3mm MDF on each sides and 0.6mm fabric on both sides. Particle board framing shall be used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables----- (Full Desc. attached in document).

Work Station PENTA 1500 x 1500 . Panel Height - 1200mm The system is modular tile based open plan office system. It comprises of two types of panels as per thickness 52.4mm. The 52.4 mm panel has more elaborate and flexible construction offering various functional and decorative finishes as well as cable management capacity. The top trims and end trims for 52.4 mm shall be made from aluminum extrusion having material AL96063-T6. All kinds of extrusions for 52.4 mm shall have average wall thickness of 1.2 mm & having finish of powder coating. Top trim in 52.4mm thick panel shall be press fitted on the horizontal extrusion it shall be slide fitted with the help of top trim connector made from PP copolymer 3530 grade. End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513. These uprights and horizontals shall be made of aluminum extrusion having material AL96063-T6 & have average wall thickness of 1.2 mm & powder coated with epoxy-polyester powder. BOTTOM FAME ASSEMBLY: Fabricated bottom frame for 52.4mm shall comprise of L- Channels made of 2mm thick CRCA steel (IS:513), formed plates of 3mm thick HR steel (IS:2062) & ERW steel tube of size 35x15x1.6mm in oval cross section (IS:7138) welded together This shall be coated with average 50 to 60 micron thickness of epoxy powder coating. This shall be bolted to the uprights with M6 screws. Tiles: Combination of top tiles are fabric tackable/white board. Bottom tiles - Plain metal. Fabric tackable tiles shall be upholstered metal tiles in 0.6mm thick G.I. grade O as per IS: 277, with 10 P.E. foam in the tile for tackablity. The fabric shall be upholstered with adhesives. White board tiles shall be made of 8.0 mm thick particle board conforming to IS: 12823 laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and will be having all its edges with minimum 0.5 mm thick PVC edging. Plain Metal tiles shall be powder coated metal tiles in 0.8 mm thick M.S. CRCA Grade D as per IS: 513. INTERMEDIATE BLOCKS A block for 52.4mm panel's thickness shall comprise of 38mm thick paper honeycomb with 3mm MDF on each sides and 0.6mm fabric on both sides. Particle board framing shall be used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks will be located in the middle bands of the panels Wire Management - Cable duct shall be made from 0.8 mm thick M.S. CRCA Grade D as per IS: 513 - 1994. It is constructed with two parts, one is body & another is cover. It holds the cables & gives aesthetic appearance by covering all cables entry, which are moving upward to the panels. Size of Cable duct is 107mm W X 154 mm H X 21 mm D. legs - The legs used for supporting panels & worktop. The height of a panel leg shall be 126mm. Panel legs/Single side legs shall be fabricated by CO2 welding MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler shall be fitted, which allows for adjustment of the height by 50mm. It will be coated with min. 45 micron thickness of epoxy powder coating. Worksurface - Work surfaces shall be made of 25mm thick Pre laminated particle board interior grade of approved shade conforming to IS: 12823. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. (rate as per quote attachd)

Back wall boxing -Making and fixing 75mm back drop boxing using 15mm ISI marked 710 grade marine plywood in decorative laminate finish. Boxing having 25mm square wooden strips 11 vertically with golden Tee profile sections embedded at spacing of every 30 Cm. Rate including cost of all materials, labour, hardware, fittings etc complete as per design. as directed by Engineer in charge

TV Console- Making and Providing TV console 16 mm marine ply of approved brand and manufacture and laminate finish as per drawing as directed by Engineer in charge

AC console-AC console making and fixing AC console using ISI marked 710 grade marine plywood in laminate finish, by closing the two shutter of existing window with necessary frame work and fittings as per design. as directed by Engineer in charge

Modification work of main door using new laminate , golden profile in groves to required pattern lock , handle, hinges etc complete as directed by Engineer in charge

REINFORCED CEMENT CONCRETE // STEEL REINFORCEMENT // Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. // Thermo-Mechanically Treated bars of grade Fe-500D or more.