Minor Irrigation Department Tender

mi004 - Providing and laying insitu vibrated M-20 ( 28 days cube compressive strength not less than 20 N / sq mm ) grade cement concrete using 20 mm down size approved, clean, hard, graded aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, including cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing, centering, formwork and scafolding and all other appurtenances required to complete the work as per technical specifications for check dam /pickups /irrigation tanks/waste weir/sluice, sluice canal and other allied works like abutments/wing walls/returns/cutoff walls works & all necessary works as directed and complete as per specification etc.., complete with all lead and lifts including loading and unloading and as per specifiction with the directions of Engineer-in-charge of work. ( Ref :- As per relevant IS)

mi005 - ELECTRICAL Winding of 100 Hp DWT 3 phase induction motor Kirloskar /jothi / Croption greaves make motor with ‘B’ Class insulating material such as triple papers , emperor cloth, cotton tape, varnish (Oil) air dry, fiber glass sleeves, legs stripping with 7/16 end connection and suitable for above motor HTP (ISI) make class-1 warking with 100c heat gauge enamel coated and insulating copper winding wire requiredas per original make. Lobour charges to lifting and the above motor including transportion charges from site to workshop and return to site and overoiling and trail runat site etc.., complete with all lead and lifts including loading and unloading and as per specifiction with the directions of Engineer-in-charge of work. ( Ref :- As per relevant IS)

mi006 - Supplying starter spares for 200 amps Air Break ATS starter Replacement of suitable contacts on volt coil, timer, pushing timer, pilot lamp amps meter and volt meter, turnel plate, push botton, MCB, Bassbar plate, a/m plates, 716 fiexible copper puc coated wire 3 If contacter for suitable HP, tripping relay unit, CT relaying, CT coil, HRC fuse function etc.., complete with all lead and lifts including loading and unloading and as per specifiction with the directions of Engineer-in-charge of work. ( Ref :- As per relevant IS)

mi007 - PUMPING MACHINARY Supplying of Spare parts to 100 H P oil lubricated DWT pump to facilitate from site to workshop by removing motor turbine base, tee joint, column pipes, line shafts and bowl assembly etc., complete, Supplying of Spare parts to bowl assembly by providing and fixing of gun-metal casted, machining, turning, boring and finishing for required sizes and fixing of suction and discharge case bearing, interstage case bearing, Supplying of Spare parts to trueness and trueing of bowl assembly stainless shaft with S S welding, turning, machining for original dimensions of the shaft, Supplying of Spare parts to trueness and trueing the impeller including inner finishing for shaft sizes and externally machining to required sizes, Supplying of Spare parts to TT nut with replacing new GM bush,Supplying of Spare parts to stuffing box by means of boring, turning and internally left hand threading for oil tube sizes, Supplying of Spare parts to gland rope for TT nut, Supplying of Spare parts to adopter screw gun metal bearing including cost of new gun metal bush and machining for bowl assembly shaft sizes,Supplying of Spare parts to line shafts of all sizes including welding and turning for required sizes, Supplying of Spare parts to oil tubes bycutting both ends of each 5 ft length oil tube including jointing of new M S tubes suitable for oil tubes with internally left hand threading for bearing sizes, Supplying of Spare parts to oil lubricated gun metal bearings suitably pattern casted, internally machining and finishing for line shaft sizes and externally turning, machining and left hand threading as per the sample original bearing, Supplying of Spare parts to bolts and nuts packing rubber, gland rope, etc., jointing materials, after attending all repairs same has to facilitate from workshop to site and Re erection of pump after attending job works including assembling all the parts with erection and trail running etc., complete with all lead and lifts including loading and unloading and as per specifiction with the directions of Engineer-in-charge of work. ( Ref :- As per relevant IS)

mi008 - Supplying spare parts and repair, reconditioning, trail running of 14" size N.R valve, including dismantlingand facilitate from site to workshop by removing from delivery end of T joint including supply of spare parts like gun metal bushes, hinges shop, stainless steel square threading shaft, square threading shaft gun metal nut, guid ring to tongue of suitable sizes, paking rubble, bolt and nuts with washers of required sizes, and other jointing materials, the work involves this melting necessary repais including threading, straightening, turning, machining, finishing etc,. complete with attending all necessary job works including assembling all the parts with erection and trail running etc., complete with all lead and lifts including loading and unloading and as per specifiction with the directions of Engineer-in-charge of work. ( Ref :- As per relevant IS)

mi009 - Consumables Transformer oil-@ Jackwell

mi010 - SAE10 oil -Jackwell

mi011 - Grease GEM-RR3