Directorate Of Municipal Administration Tender

vol 1 2.1.4 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications.Mix 1:3:6 (M10) Using 20 mm and down size graded crushed coarse aggregates

vol 3 6.8.1 - Providing and laying 60mm thick factory made precast M -30 grade Cement Concrete Paver Block as per IRC SP 63:2018 & IS 15658 for Cycle Tracks & Pedestrian Footpaths of approved shape and colour, laid in required pattern and including over 30mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-incharge. (WMM/WBM Base to be paid separately if necessary as per relevant technical specification)

vol 3 8.42.7 - Supplying and fixing M15 grade precast cement concrete Kerb stones for Roadway, Sidewalls and gutters fixed with CM 1:3 fixed and finsihed in line as per direction of Engineer in charge. (The cost of PCC shall be paid extra) 300 x 300 x 150 mm Kerb Stone

vol 3 8.10 - Painting Two Coats on New Concrete Surfaces, Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces

Approved rate 01.09.2023 - CrossWalker Providing, Supplying, fixing, installation, commissioning and trial run of Cross Walker. Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5%NaCI solution in accordance to ISO 7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. SizeLxWxH: 2015 x615x1360mm (min) Weight: 93 KG (min) Safety Area: 5015x3015mm (min),Capacity 2 persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge

Approved rate 01.09.2023 - Leg & Thigh Excercise/Air Walker Providing, Supplying, fixing, installation, commissioning and trial run of Air Walker . Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5%NaCI solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. SizeLxWxH: 1065 x615x1364mm (min) Weight: 51KG (min) Safety Area: 4090x3555mm (min),Capacity 1 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge

Approved rate 01.09.2023 - Seated Chest Press Providing, Supplying, fixing, installation, commissioning and trial run of Seated chest Press. . Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5%NaCI solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. SizeLxWxH: 1955 x733x2058mm (min) Weight: 86.60KG (min) Safety Area: 5545x4470mm (min),Capacity 2 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge

Approved rate 01.09.2023 - Waist Twister Triple Providing, Supplying, fixing, installation, commissioning and trial run of Waist Twister. Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5%NaCI solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. SizeLxWxH: 1460 x1310x1150mm (min) Weight: 39.10KG (min) Safety Area: 4360x4510mm (min),Capacity 3 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge.

Approved rate 01.09.2023 - Single Pole Setup Cycle Providing, Supplying, fixing, installation, commissioning and trial run of Single pole set up Cycle Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5%NaCI solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. SizeLxWxH: 1000 x498x1290mm (min) Weight: 51.50KG (min) Safety Area: 3400x3498mm (min),Capacity 1 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge