Military Engineer Services Tender

M&L cement concrete 1:2:4 type B-1 as in copings including weathering slightly rounded or chamfered angles and throating incl formwork.

M&L rendering 15mm thick cement plaster on fair faces of brick work or concrete surfaces and finishing surface even and smoth compelte all as specified in 1:4 CM.

Dismantling posts/pillers or struts (Wood, Steel, or RCC) any section, including taking out embedded portion in natural ground and making good disturbed ground.

S&F Mild steel framed work as in posts and struts in fencing including cutting tops to shape as directed, drilled holes,notching for wire etcflats iron fillets (for securing wire mesh etc ) including all necessary drilling,bolting or fiveing etc, and similar work confirming to Fe-290 GdeE -165 all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40 mm graded stone as in foundation , filling and mass concrete as in post holes, surface channels and drain etc complete all as specified and directed.

Dimantling Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings.

S&F Pre-painted galvalum alm zink coating GI based corrugated/ semi - corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with coach screw as per manufacturers instrution complete.

Preparation of new steel surfaces and two coat of synthetic enamel paint over a coat of red oxide primer.

Preparation of old steel surfaces and one coat of synthetic enamel paint complete

M & L preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of priming coat complete.

M & L for complete removal of existing treatment of wall surface and preparation of wall and applying two coats of cement base paint over a coat of priming coat complete.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area n’exc1.5 Sqm and removing from site.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc1.5 Sqm but n.exc 4.00 Sqm each and removing from site.

Cutting holes in brickwalls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required not exc. half brick

S&F of aluminum powder coated doors with box section frame of 65 x 35 x 1.15mm thick, shutter with top and bottom rail of section 100 x 45 x 1.35mm thick, style and middle rail of section 45 x 45 x 1.35mm thick with locking arrangements with lock (Make – Godrej) with rebates including jointing cleats for fixing builder hardware fittings, , grating clips, rubber packing for air locking purpose, handle 120mm dia pivot, aluminium tower bolts 150mm long, anodized aluminium snap beading screw etc for fixing glass panes in frame shutter covered with fully selected quality sheet glass of 4.8 mm thick with rubber packing complete all as specified and as directed.

S&F powder coated anodised/aluminium frame of size 65mm x 38mm x 1.00 thick or appropriate section as directed including with frame standard section for sliding type windows /ventilatorss with one or more rebates including joining cleats, beading, handle with locking arrangement, rubber gasket for fixing etc complete with and including 5.5 mm thick tinted glass n.exc 1 Sqm each panes (window of frame 3 tract wt not less than 0.50kg/RM and shutter having wt not less 0.45kg/RM) all as specified and directed

S&F in repair door closer hydraulically regulated, designated No- 2 universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 kg aluminium (die cast) body.

S&F door closer hydraulically regulated, designated No- 2 universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 kg aluminium (die cast) body.

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

Dismantling of wall and ceiling board any thickness/description including cover fillet .

S&F for Anodised Aluminium snap grid size 605x604mm frame work for false ceiling all as specified and directed by Engr-in- charge.

M&L 4mm thick non asbestos fibre cement designer building board of size 600X600 fixed or laid/inserted to timber/GI/Aluminium framework fixed in ceiling flat or sloping.

Dismantling timber scantling 40 sqcm and over in section in any position in un-framed work complete.

M&L for preparing old plastered surfaces of wall and applying two coats of distemper oil emulsion over one coat putty .

M&L Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to fe.290.Gde-E-165

Demolition of cement concrete (un-reinforced) in ground floors and paving n.exc 15cm thick (below or above ground level).

M&L for 75mm thick PCC type C2 1:3:6 (using 40mm graded stone agg) as in plinth protection/Path/floor finishing surface of concrete topping even and fair without using extra cement complete.

M&L for Chequered cement concrete tiles (300x300x25)mm thick, set, jointed and pointed in neat grey cement slurry in floors incl 15mm thick screed bed or bedding layer of mortar in CM (1:6) for lying floor finishes .

Sand filling under floors or in foundation including watering and consolidation for laying interlocking tiles complete all as specified and directed.

M& L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and no pigment in paths and hardstanding laid tightly over dry sand cushion (compacted) and joint filled with dry sand(colour and pattern as approved by GE) complete all as specified and directed.

M& L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and no pigment in paths and hardstanding laid tightly over dry sand cushion (compacted) and joint filled with dry sand(colour and pattern as approved by GE) complete all as specified and directed.

S&F 18 mm thick Rajshree Celuka ply or equivalent as approved of grade 1 quality with both side plain white or coloured fixed with stainless steel screwes, solvent cement /adhesive to fabricate kitchen cabinet sides , top and bottom, door, shelf inside the cabinet and drawer including ,drawer chanel, magnetic ballcatch & other all fittings complete all as per manufacturers instructions incl taking out old existing wooden cabinate.

S&F auto closing hinges 35mm of crank(KH-001) or 8 crank (KH-002) openable at 110 degree of make as approved.

S&F stainless steel handles of 100mm size.

Supply and erection of Earth electrode 17.2 mm dia 3 mtr long of low carbon steel electrode with copper bonding of thickness 250 micron, Back-fill earthing enhancing compound AXIS ULTRA / AXIFILL type Carbon based compound conductive concrete type which has a resistivity of less than 0.12 Ohm Mtr as per Clause 14.5D of IEEE : 80 standard. Back-fill compound should be electronically conductive (Like in metals) and should not depend on moisture for conduction. Back-fill comound should be environment friendly & should be solidify when mixed with water and set like concrete and should not leach / diffuse into the ground. Back-fill compound shall not be mixed with any soil while pouring in the bore hole. Test Certificate as per as per IEC: 62561-7 for Back-fill compound shall be submitted along with the material including SS clamp to be provode both side and PVC EARTH PIT 300 X 300 MM WITH PLASTIC LID complete all as specified Note - (i) Earth electrode should be applicable Standards IS: 3043, IEC 62561-2 & IEC 60364-5 and made of High Tensile steel rods copper bounded, High tensile strength,good electrical conduction & effective performance and suitable for all type of soil and provided minimum distance 3 Mtrs. (ii) Back-fill compound should be Compliance to the Standards IEEE: 80, IS-3043, BS 7430, IEC 62561-7, ANSI/NSF 60 Certification.(iii) Positive low resistance electrical connection to the earth. (iv) Does not contain hazardous chemicals.(v) Electronically conductive (like in metals) and is not dependent on moisture.(v) Provide the desire value of earth resistance as per required specified values. (vi) Provide the Exothermic welding joints to entire grid system joints of earthing electrod. Make : OBO Betterman/Axis/ UTR

M&L for copper strip 20 x 3.15mm with saddles and fixing screws etc for roof conductors and down conductors of pole and above ground with require connected items with sinkable sleeves and insulator per meter complete all as specified and as directed. Note : All joints of copper shall be of brazing only and including in quoted rates of items.

S&F test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 32 mm long hex. head screw complete all as specified and as directed

M&L for termination single pointed copper rod.12mm dia 300 mm fixed to roof and pole including required accessoreis for fixing complete all as specified and as directed.

S&F LED highbay light 150 W & replacement of defective wiring with PVC copper wire inside conduit pipe with fixed at the ceiling of Hangar.

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates