Military Engineer Services Tender

M&L for cutting CI/DI/GI pipes and reduction to required length before laying including insertion of new Tees, branches etc of size upto 150 mm dia all complete.

Supply only MS ERW water pipe of 100 mm dia (Make : Jindal or equivalent as approved)

M & L for cast non return valve of 100 mm dia ISI Marked, confIrming to IS14846 both ends flanged class PN1.6 and necessary new MS nuts, bolts, washer and gasket, including taking out old u/s ones for credit and making good etc complete all as specified and directed.

M & L for cast iron sluice valve of 100 mm dia ISI Marked, confIrming to IS14846 both ends flanged with ss spindle, class PN1.6 and necessary new MS nuts, bolts, washer and gasket, including taking out old u/s ones for credit and making good etc complete all as specified and directed.

M & L in replacement for DI/CI special fitings like bends, tapers, tee, tail pieces,collars etc suitable upto 100 mm dia pipes including necessary welding works at site requirement .

M & L in replacement for DI/CI special fitings like bends, tapers, tee, tail pieces,collars etc suitable upto 200 mm dia pipes including necessary welding works at site requirement .

M&L for Ductile Iron pipes 150 mm, spigot & socket end, centrifugally cast (spun), Class K-9, confirming to IS-8329/ 2000 or latest revision, in any length, laid in trenches/PCC base /RCC columuns, with & including EPDM rubber gasket confirming to IS:9523/2000 or latest revision, connecting & testing complete all as specified & directed .

M & L for cast iron sluice valve of 150 mm dia ISI Marked, confIrming to IS14846 both ends flanged with ss spindle, class PN1.6 and necessary new MS nuts, bolts, washer and gasket, including taking out old u/s ones for credit and making good etc complete all as specified and directed by Engr-in-Charge.

M & L for Joint with rubber or fibre board gasket for bore upto 200 mm dia size complete all as specified and as directed.

M&L for PCC type B-2 1:2:4 (40mm graded aggregate) line Cement concrete foundations, filling and mass concrete all complete all as directed

M&L for Reinforced cement concrete (nominal mix) Type B 1:1.5:4 (12.5 mm graded stone aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all complete all as directed

M&L for Formwork to sides of concrete rough finished surface flat for foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batteall complete all as directed

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all complete

M&L for Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc. Fe 410 -W (GdeE- 250) qualityA (cut to ordinary lengths all complete all as directed .

M&L for new steel Surfaces of any description, over 10cm in width or girth with two coats of black japan paint over primer with red oxide zinc chrome primer all complete all as directed

M&L for SS flexible pipe of dia 100 mm, single braided with both side flanges all as specified and as directed .

M&L for HDPE pipe of dia 100 mm, welded with 2 stud ends and 2 MS slip flange inserted UV stabilized raw material all complete all as specified and as directed .

M&L for pipe floater for pipe size 100 mm dia, high impact polyethylene PU foam filled UV stabilized raw material bolts, nuts, rubber pads and belts, colour orange all complete all as specified and as directed .

M&L for anchoring and mooring as the floating platform with necessary bollards, RCC anchors with suitable weight and size, chain with suitable size, diameter and length all complete all as specified by OEM and as directed by Engr-in-Charge. Make : Vari Pontoons or equivalent

M&L for floating platform of total size 10 x 2 mtr made of HDPE High Density Polyethylene block buyos interlocking in nature of dimension of each block 50cm x 50cm x 40 cm cubical in shape and modular in nature that enable easy assembly and dismantling the required size all complete with load capacity 350 kgs/m2 and complete with railing to bear load of suction line of HDPE pipe of dia 100 mm with stainer and foot valve of size all complete all as specified by OEM and as directed.

M & L for PVC insulated, heavy duty, industrial copper cables of 35 sqmm, single core unsheathed 1100 volts grade conforming to IS : 694 for connection of motors etc with copper lugs for suitable size complete all as specified and as directed.

Supply and fixing of powder coated peforated cable tray of 100 mm width 50 mm height with cover C type for cable dressing including coupler, junction boxes, screws, fastner etc all complete and fixing charges as directed .

Excavation in trenches in soft/loose soil n.exc 1.5 mtr wide and n.exc 1.5 mtr deep getting out of soil for taking out/laying of pipe line etc.complete all as specified & directed .

Returning, filling in, including spreading, levelling watering and well ramming in layers not exc 25 cm.complete all as specified & directed.

Removing excavated mateials n.exc 50 mtr & depositing where directed at a level n.exc 1.5 mtr above the starting point.complete all as specified & directed .

M & L for Foot Valve stainer brass end 100 mm Dia ISI Marked brass made complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x 6mm thick burried in ground (earth pit not less than 2.25 m deep below ground level0with top edge of the plate not less than 1.5 m below normal ground level, connected to earth lead wire 4.0mm dia as earthing lead by means of bolts, nuts, check nuts, and washers of GI or steel, GI strip protected by 40 mm bore medium grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade GI, wire mesh charcoal or coke common salt laid in altrnative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC(1:3:6) type C-1, 50 mm thick pre-cast RCC(1:2:4) type B-1 normally mix cover slab reinforced with in 8 mm dia TMT bar 10 cm C/C both ways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft/loose/hard soil and disposal of soil to a distance n.exc 50 m and necessry testing on completion all as shown in electrical plate No 3 MES schedule part-I complete all as specified and as directed.

All as Sl item No. 31 above but using galvanised iron strip 25×4mm as earthing lead

Supply and fixing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 70 sq. mm, 3.5 core complete all as specified and as directed.

Supply and laying new dry river sand laid in trenches 8 cm below the cable and 15cm above the cable and punned to 18 cm as cable cushioning and covering all as directed.

Supply and laying in replacement of brick well burnt locally available sub class 'B' laid over sand cushioning for cable protection in trenches width of brick perpendicullar to the length of cable complete all as specified and directed by Engr-in-Charge.

M&L for 20 mm dia galvanized steel tubing (medium grade), with all fitting laid in trenches complete all as specified and as directed.

S & F for 20 mm gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

S & F for pressure gauge 100mm dial, 0-14 Kgs rating with fittings as per site requirement complete all as specified and directed.

S&F LT Panel board with copper loop bus bar of capacity 600A ,made out of CRCA sheet 3.15 mm thick otdoor pedestal type totally enclosed with front and rear opening, hinged doors of size 1.0 m x 1.2m x 0.5 m, with projected an raised platform of suitable size weather and water proof with necessary locking arrangements along with lugs, danger notice plate, strickering of Switcher gear about termination of switch gear, and the nuts/ bolts etc used are to be made of rust proof material incl as per IS: 8623 copper bus bar (incoming and ougoing side) mounted on insulators as per IS with heat proof colour code, insulators suitable for three phase and four wire LT AC, 50 Hz 415 V 500 A capacity complete with powder coating, necessary internal electric connection as required and provision of the following: Incoming:a) LT 440 volts 3 phase, 4 wire 50 cycles, 20kA, Adjustable type MCCB of 300 Amp rated 4 pole complete as per IEC: 60947-II, adjustable thermal and fixed magnetic , Ics=100% Icu . Make:Havells, Cat Part No: IHD2HTBF0250/Indoasian / Schnieder/ Siemens - 1No. Outgoing:a) LT 440 volts 3 phase, 4 wire 50 cycles, 20kA, Adjustable type MCCB of 200 Amp rated 4 pole complete as per IEC: 60947-II, adjustable thermal and fixed magnetic , Ics=100% Icu . Make:Havells, Cat Part No: IHD2HTBF0160/Indoasian / Schnieder/ Siemens 2 Nos.(b) Fully Automatic star delta starter complete with under voltage and over voltage relays, contactor etc suitable for 75 HP pump motor ac 415 volt three phase-02 nos. (c) Supply and fixing MCCB C-Curve, 32 Amp TPN, 50 Hz, 240/415 Volts complete all as directed.Make:Panasonic, Cat Part No:BBD4633CHH /Indoasian /Schnieder - 01 No(d) LED Indicating Lamps for ech phase with colour coed Red Yellow Blue for R, Y and B Phases-01 Set(e) Multifunctional Intelligent Panel Meter digital type for measuring Volts, Current, Hz, pf, power, energy, THD along with connected CTs Make: Schinder / L&T-01 No

Repair/Maintenance/Cleaning of jack well including taking out of sludge / desilting from jack well water and depositing upto 150 mtr to 200 mtr distance and lifting from 12 to 15 meter depth from Jack well pump room flooring level including repairs and cleaning / clearing the blockage of 3 Nos gates on the jack well for smooth inlet of water inside the well and making it in serviceable condition including required dewatering / welding/ greasing/oiling if necessary repairs required complete including any type of materials required for the job all complete all as specified and as directed .

M&L for Micro Concrete ready to use dry powder mix form that only needs clean water added at site consisting of cement, river sand, quartz sand, lime, water based resin, additives, mineral pigments and polymers in the specified ratio all complete to be applied in thin layers of around 2 to 4 mm on concrete surfaces to refurbish them all complete all as specified.