Building Construction Department Tender

Earth Filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Providing coarse clean Sand in Filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 B one Brick Flat Soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing and laying in Position Cement of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 cement : 3 coarse sand (zone-lll) :6 gradde stone aggregate 40 mm nominal size)

providing and laying in position specified grade of Reinforced Cement Concrete ,excluding the cost of centering ,shuttering, finishing and reinforcement - All work up plinth level. 1:1.5.3 (1 cement :1.5 coarse sand (zone-lll): 3 graded stone aggregate 20mmnominal size)

Providing designation 75 B Brick Work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

providing and laying Damp- Proof Course 50mm thick with cement concrete 1:2:4 (1 cement :2 coarse sand (zone-lll) :4 grade stone aggregate 20mm nominal size).

Reinforced Cement Concrete work in beams, suspended floors, roofs having slope up to 15 degree landing, balconies , shelves , chajjas , lintels , bands, plain windows sills, staircases and spiral stair cases above plinth level up to floor five level , excluding the cost of centering , shuttering , finishing and reinforcement, with 1:1:5:3 (1 cement :1.5 coarse sand (zone-lll) : 3 graded stone aggregate 20 mm nominal size )

Reinforced Cement Concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Providing Tor Steel Reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. TMT Fe 500

Providing Tor Steel reinforcement of 10mm. ,12mm & 16mm dia. bars as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

(a) 10 mm (TMT,Coil Fe 500)

(b) 12,16 mm (TMT,Coil Fe 500)

Centring and Shuttering including strutting propping etc and removal of form for foundations, footings, bases of columns, etc. for mass concrete.

Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Supplying, fitting and fixing M.S. Grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Supplying, fitting and fixing Collapsible Gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l.

Providing Primer one coat of red lead paint of approved make over new Steel surface including preparing the surface after cleaning, removing rust , dirt, , scales , smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l. ( Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coats of synthetic Enamel Paint of approved shade and make over Steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing and fixing Aluminium Work for doors, Windows, Ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285 fixing with dash fasterners of required dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required DPDM rubber/neoprene gasket etc., aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/panelling C.P. brass/stainless steel screws, all complete as per architetural drawings and the directions of Engineer-in-charge (Glazing, panelling and dash fasteners to be paid for separately)For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required inlcluding the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for separately) --- Polyester Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing Glazing in Aluminium door, Windows, ventilators, shutters and partitions etc, with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge (cost of aluminium snap beading shall be paid in basic item) With float glass panes of 4.0 mm thickness

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in Chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush Door Shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing and laying double charge vitrified Floor Tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm

Providing and laying Vitrified Tiles in Floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1 : 4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Size of Tile 600 x 600 mm.

Providing and laying 6mm precast white glazed Tiles in Walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. Glazed Vitrified tiles Matt/Antiskid finish of size- With commercial grade colour 15X15cm Tiles.

Providing and laying 25mm thick Kotah Stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm thick cement Plaster (1:4) in Ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm cement Plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm cement Plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing and applying White Cement based Putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Finishing with acrylic paint approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Water Proofing for Old and New Roof Slab Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied with brush, roller or spray for water proofing coating as per manufacturer specifications with following steps:- (a)surface preparation-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint/ coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete Ponding test to be done after plugging all outlets and to be checked from soffit to identify see page, leakage. On identification of seepage, cement grouting to be done with non shrink expanding admixture of Sika India Pvt Ltd. MYK Schomberg Dr Fixit/Fosroc or equivalent Providing and reparing of all corners and joints such as those between the parapet wall and the roof slab etc shall be chamfered with 150mm X 150 mm fillet of mortar (Cement sand 1:4) admixed with acrylic polymer of Sikal Fosroc MYK Schomberg/Dr Fixit or equivalent. Before chamfering a prime coat shall be given with the slurry of acrylic polymer Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete (b)1st Coat Apply 1st coat of two component acrylic modified, ready to use, flexible cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller After 1st coat of application, 45 gsm of Fibre glass cloth to lay when the first layer is still green 1st coat should be applied @150 kg/Sgm/coat For the purpose of measurement the entire treated surface will be measured." (c) 2nd Coat-To apply the 2nd coat of two component acrylic modified, ready to use, flexible cementitious material right angle to the 1st coat over the glass fibre laid surface 2nd coat should be applied @0.7 kg/ Sqmt/coat For the purpose of measurement the entire treated surface will be measured" After three days of drying the 2nd coat, the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it Waterproofing Brand. Sika Topseal 109hi Fosroc Brushbond RFX/Dr Fixit Pidiffin 2K/MYK Aquafin TG Product Performance Chemical Base Part A Acrylic copolymer, Part B: Specially graded cementitious powder Density 1.6 kg/l (mixed density) at +27°C Tensile Strength 2 N/mm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Strength -2 N/mm2 (concrete failure) (According to ISO 4624). Slant-Shear Bond Strength 4 N/mm2 (According to FIP 5.15) Elongation at Break -35% without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370) (d) Protection of treated surface with PCO The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1:5:3) with proper slope (1:120) towards the rain outlets in alternatepanels of 2 mt x 2mt keeping 6 mm gap between the panel joint Integral water proofing admixture conforming to IS 2645 @ of 100 ml per bag of of cement to be added in the screed concrete (paid separately for this items) Al corners shall be chamfered with 150mm X 150 mm fillet The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water the peripheral gaps between pvc pipe outlet and concrete surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture insensitive epoxy putty of Sika India " Pvt. Ltd. MYK Schomberg Dr Fixit/Fosroc For the purpose of measurement the entire treated surface will be measured.

Covering of treated surface with PCC Providing 50 mm thick Cement Concrete M20(1 1.5.3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and cement concrete in mixer with admixture of integral water proofing and cleaned sand of F.M 2.5 to 3 including screening.shuttering, and mixing placing in position striking curing taxes and royality all complete as per building specifiction and direction of E/.Panels that has been left should be casted next day. There should be 6 mm gap between Panels Brand Sika Plastocrate plus, MYK proof WP 10. Fosroc-Conplast X421 ic Dr Fixit Pidiproof LW+

Providing and filling of 6 mm thick Groove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of Ein Charge (with 18% GST) Brand Sika Polysulphide. Fosroc-Thioflex 600. Dr Fixit Pidiseal PS(42P, MYK Seal PS or Euivalent

Making Plinth Protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand :6 agraded stone aggregate 20mm nominal size ) over 75mm thick bed of dry brick ballast 40mm nominal size , well rammed and consolidated and grouted with fine sand , including necessary excavation , levelling & dressing & finishing the top smooth.

Providing 1.5mm Cement Punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Providing 250mm. Wide Brick Drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l.

Carriage of Material

Bricks Lead (7P+1K=8km)

Sand lead = 5 km(1K+4P)

Stone Chips Lead (7P+1K=8km)

Local Sand lead = 3km

Point Wiring in PVC Conduit, with Modular type Switch :- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box etc as required.- Group C

Supplying and fixing batten/ angle holder including connection etc. as required.

9/10 Watt LED Bulb

S.I.T.C of following rating recess/surface mounting round/square shape downlight with pressure die cast housing for single phase supply voltage. Luminaire shall conform to IS: 3022 part-5/ section-5 or IEC:62722 with all necessary accessories as required.

80W LED Flood light

S.I.T.C of following rating recess/surface mounting round/square shape downlight with pressure die cast housing for single phase supply voltage. Luminaire shall conform to IS: 3022 part-5/ section-5 or IEC:62722 with all necessary accessories as required.

12W LED Round light

S.I.T.C of following rating surface mounted LED tube lightfitting suitable for 230V 50Hz, single phase supply etc. complete as required. 20W/22W LED tube.

12" (300mm) Exhaust Fan

16" (400mm) Wall Fan

Installation of exhaust fan upto 450mm/sweep in the existing opening, including making the hole to suit the size of the above fan making good the damage, connection, testing, commissioning etc. as required.

S/F Modular type electronic fan regulator :- Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supply, fitting, fixing and testing of 1200mm Sweep, BLDC, 5star Fan 32W

S/F Light plug point with modular type accessories :- Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection,painting etc. as required.

S/F Light plug point with modular type accessories :- Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch, connection,painting etc. as required.

S/F 20amps SPN MCB industrial Socket :- Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

S/F Modular boxes, base & cover plate :- Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.

4/5 Module (78mmX140mmx50mm)

12 Module (135mmX205mmx60mm)

S/F Modular type blanking plate :- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit.

4 X 16 sq. mm + 2 X 16 sq. mm earth wire

4 X 10 sq. mm + 2 X 10 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit.

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Copper earth pipe electrode :- Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and fixing 25mm x 5mm copper earth strip in surface/recess :- Providing and fixing 25 mm X 5 mm copper strip at surface or in recess for connections etc. as required.

Supplying and laying 25mm x 5mm G.I.strip at 0.50 metre below ground as strip earth electrode, including soldering etc.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt ) as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete etc. as requited (horizontal run).

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete etc. as requited (Vertical run).

Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed armoured electrical cable with aluminium conductor for working voltage upto 1.1 KV etc as required.

3.5c x 25 sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 35 sq mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

1.1 KV Cable end Termination :- Supplying and making indoor cable end termination with brass double compressing gland and aluminium lugs for following size of PVC insulated XLPE Al.Ar. Cable of 1.1 KV grade as required.

3.5c x 25 sq.mm (28mm)

Supplying and fixing following way, three pole and neutral, sheet , MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.

6 way (4 + 18), Double door, Horizontal type

8 way (4 + 24), Double door, Horizontal type

Supplying and fixing 6 amps to 32 rating, 240 volts, 10kA "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

63A rating, TPN MCB, "C" curve 10 KA breaking capacity.

40A rating, TPN MCB, "C" curve 10 KA breaking capacity.

6/33A rating, TPN MCB, "C" curve 10 KA breaking capacity.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual circuit breaker (RCCB), having a sensitivity current upto 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

25 amps

40 amps

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Indoor Type Main Distribution Board fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing , dust and vermin proof, (degree of protection-IP54)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated) as per Specification. The Main LT Panel shall broadly comprise of the following equipment/components) 40A TPN MCB 10kA - 02 Nos. 63A TPN MCB 10kA - 02 Nos. 100A TPN Copper bus bar in metal encolsure with fixing clamps Indication lamps(On- Off Trip Power On -- RYB)

Supplying, Installing, Testing & Commisioning cost of Main LT Panel for Manki Munda Bhawan all complete with all necessary items as per direction of E/I.

Providing and placing on terrace (at all floor levels) polyethylene Water Storage Tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) Pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) Pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External Work-

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

Providing and fixing on wall face unplasticised Rigid PVC Rain Water Pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing unplasticised -PVC Pipe Clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1 : 4 (1 cement: 4 coarse sand) and making good the wall etc. complete.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC Moulded Fittings/Accessories for unplasticised Rigid PVC rain water pipes conformingto IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler- 110 mm

12.42.3 Single tee with door- 110110x110 mm

12.42.3 Single tee without door- 110110x110 mm

Bend 87.5°- 110 mm bend

Shoe (Plain)- 110 mm Shoe

Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry hindustan or any other ISS approved make with 100mm HCI p trap 15 litres CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings CI or C C bracket 32mm alkethene / PVC telescopic flush pipe about 2m long with one brass coupling and clamps GI chain and pull including supplying and fixing a pair of vitreous white glazed earthenware footrest to be fixed in floor 15mm CI body brass spindle stop cock of weight not less than 50 grames 15mm PVC connection pipe 450mm long and coat of red oxide primer etc all complete as per specification and direction of E/I.

Supplying, fitting and fixing 40mm high vitreous white glazed earthen E.W.C. with ‘p’ trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and direction of E/I.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

supplying fitting and fixing vitreous white glazed earthen ware Wash Hand Basin of parry or hindustan or any other I.S.S approved make supported on painted C.I OR R.S bracket 32mm C.I brass waste 15mm dia C.I body brass spindle stop cock of approved quality of weight not less than 350 grames, 32mm PVC wate pipe 750mm long with brass coupling with one end and making plumber joints etc.all complete as per specification and direction of E/I.

Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply board and c.p. hinges to fix with mirror. (i) 600mm X450mm size

Supplying, fitting and fixing Bathroom Fittings of approved make and as per IS specification all cost complete as per direction of E/I. (all rates have been adopted from the basic rate from SOR + 10% for labour and Contractors profit)

Pillar Cock - long neck (ISI Marked)

Bib cock - long thread

Angular stop cock L.T.

Concealed stop cock reduce (ISI Marked)

Towel Ring

Towel Rail 24"

Soap Dish

Pressure adjustable shower with revolving joint

32mm dia. PVC waste pipe 750mm long with cushion

15mm C.P. nipple with coupling

Steel jali - 100mm dia.

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 3 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes ,royalty etc all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 50 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

Providing P.C.C. M-100 in nominal mix of (1:3:6) in foundation with approved quality of stone chips 20mm to 6mm size graded and mixing cement sand of F.M 2.5 to 3 including screening, shuttering, vibrating, skirting, curing, taxes and royalty all complete all complete as per specification and direction of Engineer-incharge.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)