Sher E Kashmir University Of Agricultural Sciences And Technology Tender

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

FORM WORK:- Centering and shuttering including strutting, propping etc. and removal of form for stairs,lintel ,landing etc:

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level and above plinth lvl

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Riveted and bolted

Providing and fixing Track deck crill make or equivalent H.I. rib profiled sheets 1000 to 1020 mm cover width 28-35 mm high crests at 250 to 255 mm T.C.T(total coated thickness) high tensile S.M.P Galvalume steel. The sheets shall have wide panes with 3 no stiffing ribs, effective water shedding and special male/female ends with full return legs on side Lapps for purlins support and anti-capillary flute inside Lapp. The sheets shall have a hot dip metallic coated of zinc and aluminum (150 gms /sm) zinc/aluminum coating mass total on both sides AZ-150 as IS -1397 ,550 MPA yield stress. Providing silicon modified polyester coating of approved colour of total thickness of 35 micron comprising 20 micron exterior coat of S.M.P over 5 micron polyester back coat over 5 micron primer coats on both surfaces including side and end Lapp and using 8mm Galvalume hex self-drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all sides and end Lapps etc (.measured for unit of laid area) (0.50 mm thickness )

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing and fixing 15mm thick T&G planks made of imported wood (New zealand pine or equivalent) on wood work in false ceiling, wall/wall partitions sawn and put up in position ( budloo wood Ceiling Joists of 50 mm x 65 mm in sections placed @ 600 mm C/C both ways or as required at site). including cost of necessary adhesive & cost of nails etc. all complete upto floor 5 level as per the directions of Engineer-in-charge (including cost of all material, leads, lifts and carriages etc upto site of work complete).(For panelling /Ceilings/Soffits etc.)

Providing & Fixing of Armstrong Mineral Fibre Acoustical Suspended Ceiling System with BIOGUARD ISO 5 (CLASS 100) (MICRO LOOK) EDGE TILES WITH ARMSTRONG SILHOUETTE EXPOSED GRID.The tiles should have Humidity Resistance (RH) of 95%, NRC 0.15, Light Reflectance 90%, Thermal Conductivity k = 0.052- 0.057 w/m K, Colour White, Fire Performance A2-s1.d0 in module size of 600 X"Providing & Fixing of Armstrong Mineral Fibre Acoustical Suspended Ceiling System with BIOGUARD ISO 5 (CLASS 100) (MICRO LOOK) EDGE TILES WITH ARMSTRONG SILHOUETTE EXPOSED GRID.The tiles should have Humidity Resistance (RH) of 95%, NRC 0.15, Light Reflectance 90%, Thermal Conductivity k = 0.052- 0.057 w/m K, Colour White, Fire Performance A2-s1.d0 in module size of 600 X 600 X 15mm with Anti- Bacterial coating, adhering to Clean room requirement of Class 100 as per US Fed Standard 209 E and washability requirement of 500 wash cycles as per ASTM 4828 and suitable for Green Building application, with Recycled content of 24%. The tile shall be laid on Armstrong Silhouette profile grid system with 15mm white flanges incorporating a 6mm central reveal in white/black colour and with a web height of 45mm and a load carrying capacity of minimum 15.68 Kgs/M2. Silhouette, Main Runners & Cross Tees to have mitred ends & “birdsmouth” notches to provide mitred cruciform junctions. The T Sections have a Galvanizing of 90 grams per M2 & passed through 500 hrs of Salt test. The Tile & Grid system used together should carry a 15 year warantee.

(a) 15 mm thick cement plaster on smooth side of single or half brick wall in (1 cement: 6 fine sand mix).

(b) 10 mm thick cement plaster on rough side of single or half brick wall in (1 cement: 6 fine sand mix).

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.2mm thick

Providing and fixing 35 mm thick glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.First class kail wood

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :First class kail wood

Finished Kota stone slab flooring 18 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, with base of cement mortar 1:4 (1 cement : 4 coarse sand) :

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

(b) Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. For granite work

Providing and fixing powder coated aluminium work for partitions including doors,windows,ventilators etc with extruded built up tubular sections ,appropriate Z sections and other sections of approved make fixed with rawl plugs and screws etc...ACP sheets and 8mm thick glass sheets as per design incliding all fittings and accessories (14 gauge 70x40mm and 45x45mm sections wherever required as per site requirement and directions(complete)

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Providing and fixing of ornamental doors with ornamental pannels of ist class kail wood 30 mm thick.

Providing and fixing thermal insulation of ceiling (under deck insulation) with specified glass wool conforming to IS: 8183, 50mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3mm) @ 60cm c/c and wire mesh of 12.5mm x 24g wire for top most ceiling of building. With resin bonded fiber glass wool with density 24 kg/cum

Pointing on brick masonary in lime surkhi (1 lime : 2 surkhi) including finishing the joints with lime surkhi pigment to give a heritage.

P/F 3.5 mm thick pannels of plain float glass

Providing and fixing plained eaves boarding.2nd class kail wood 300x40 mm (nominal size)

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work including cement primer.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work including priming coat on wood work.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. 100x10 mm

Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. Complete 100 mm

Providing and fixing ISI marked oxidized M.S. sliding door bolts with lock, nuts and screws etc. Complete(BRAND GODREJ)

Note:-The rates quoted are inclusive of all carriages of materials (Mechanical/Manual) from source to site work and all extra charges including dewatering if any during the execution of work complete in all respects.