Military Engineer Services Tender

Construction of Sentry Post in RCC of size floor area 3.75 sqm as per dimesions directed by Engineer-in-Charge complete all as specified and as shown on drawings.

Total amount of Schedule 'A' PART-I (BUILDING WORK)

Total amount of Sch 'A' PART-II (Sec-I) (INTERNAL ELECTRIC SUPPLY WORKS)

SCHEDULE `A' PART-II (Sec-II) (INTERNAL ELECTRIC SUPPLY WORKS) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Supply and fixing LED Flood light 70 W for operating voltage between, 110 V to 300 V, system efficiency not less than 100 lumen/watt, PF0.95 minimum, IP-66 protection, 5700CCT(K), CRI between 80-85, conforming to LM79 and LM80 minimum 5000 hours consisting to high/low voltage cut off, maintenance free isolated electronic driver with over voltage protection, surge protection and other saftey test as per IS 15885 Part-2/Sec 13, Low THD, PMMA grade high quality transmittance lens, Epoxy powder coated Die cast aluminium housing (Heat sink) with UV stabilized optics, polycarbonate LENS for symmetrical light distribution, weather proof gasket for lamp & driver compartment, with External 10 KV surge protection and Internal 4 Kv surge protection , SC,OC,OVand OT protections etc ,Heat resistance toughened UV stabilized glass fitted in cast aluminium housing with SS screws, complete all as specified and as directed.

Supply and fixing LED Flood light 100 W for operating voltage between, 110 V to 300V, system efficiency not less than 160 lumen/watt, PF0.95 minimum, IP-66 protection, 5700CCT(K), CRI between 80-85, conforming to LM79 and LM80 minimum 60000 hours life span consisting to high/low voltage cut off, maintenance free isolated electronic driver with over voltage protection, surge protection and other saftey test as per IS 15885 Part-2/Sec 13, Low THD, PMMA grade high quality transmittance lens, Epoxy powder coated Die cast aluminium housing (Heat sink) with UV stabilized optics, polycarbonate LENS for symmetrical light distribution, weather proof gasket for lamp & driver compartment,with External 10 KV surge protection and Internal 4 Kv surge protection , SC,OC,OVand OT protections etc , Heat resistance toughened UV stabilized glass fitted in cast aluminium housing with SS screws, complete all as specified and as directed.

Supply and fixing LED Flood light 210 W of LED for operating voltage between, 110 V to 300V, system efficiency not less than 160 lumen/watt, PF0.95 minimum, IP-66 protection, 5700CCT(K), CRI between 80-85, conforming to LM79 and LM80 minimum 60000 hours life span consisting to high/low voltage cut off, maintenance free isolated electronic driver with over voltage protection, surge protection and other saftey test as per IS 15885 Part-2/Sec 13, Low THD 10% , PMMA grade high quality transmittance lens, Epoxy powder coated Die cast aluminium housing (Heat sink) with UV stabilized optics, polycarbonate LENS for symmetrical light distribution, weather proof gasket for lamp & driver compartment, Heat resistance toughened UV stabilized glass fitted in cast aluminium housing with SS screws with External 10 KV surge protection and Internal 4 Kv surge protection , SC,OC,OVand OT protections etc , complete all as specified and as directed.

Total amount of Sch 'A' PART-II (Section-II) (INTERNAL ELECTRIC SUPPLY WORK)

Total amount of Sch 'A' PART-III (FLAME PROOF WIRING WORKS)

Total amount of Sch 'A' PART-IV (INTERNAL WATER SUPPLY WORKS)

Total amount of Sch 'A' PART-V (PLUMBING WORKS)

Total amount of Sch 'A' PART-VI (ROAD AND PATH WORKS)

Total amount of Sch 'A' PART-VII (AREA DRAINAGE WORKS)

Total amount of Sch 'A' PART-VIII (SEC-I) (SEWAGE DISPOSAL WORK)

Sch 'A' PART-VIII (SEC-II) (SEWAGE DISPOSAL WORK) Note: This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Supply and fixing of LLDPE tank for 10 users including vent shaft and other necessary fixing arrangment including necessory excavation, earth work and other civil works as per manufacturer's recommendation complete all as specified and as directed Make- Sintex or equal approved Make of Comfert polymers or Polycon

Material and labour for soakage wells of size 2.00m dia x 4.50m deep (effective depth) including PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in foundation, brick masonary wall of honey combed masonry, with top ring of M25 concrete including intercepting chamber and screen chamber made of brick masonry in Cement mortar 1:4, RCC cover slab in M25 design mix concrete, interconnecting pipes of RCC/DWC complete filled with brick bats of appropriate size, including necessary excavation and earth work in any type of soil complete all as specified and as shown in relevant drawing(s).

Total amount of Sch 'A' PART-VIII (SEC-II) (SEWAGE DISPOSAL WORK)

Total amount of Sch 'A' PART-IX (EXTERNAL WATER SUPPLY WORK)

Total amount of Sch 'A' -X (Section-I) (EXTERNAL ELECTRIFICATION WORK)

Sch 'A' Part-X (Section-II) (EXTERNAL ELECTRIFICATION WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Material and labour for Bus bar chamber outdoor type, made out of CRCA sheet 3.15mm thick, 750 x 400 x 750 mm with 04 Nos aluminum bus bar of 63 amp capacity with horizontal Al Bus bar alongwith the length of Box with Al Busbar extension upto 230 mm long for cable connection, RYB indicator lamps and angle iron of 50 mm x 5mm thick base frame made of MS angle with including MCCB 63 Amp 4 Pole 16KA as incomer all as required at site and as directed.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6.0mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 mtr below normal ground level, connected to and including 4mm GI wire as earth lead burried into ground and connected by means of bolts, nuts, check nuts and washers of galvanized standard iron or steel all as specified or indicated in electrical plate No 3 of MES Part-I, including testing on completion including the material and labour of the following: - (a) Excavation and earth work or drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1. (c) Precast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. (d) Funnel with watering pipe of GI 20 mm nominal bore medium grade and copper lugs etc all as specified. (e) 15 mm nominal bore light grade GI protection pipe 5 mtr long for protection of earthing lead from mechanical injury or tempering. (f) Requisite quantity of common salt and charcoal. (g) Testing of earthing. Note: (1) The earth resistance shall be less than 5 ohms after completion of earthing. If the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of the Engineer-in-Charge.

Supply and fixing LED street light fitting 35 Watt for operating voltage between, 110 V to 300V, system efficiency not less than 100 lumen/watt, PF0.95 minimum, IP-66 protection, 5700CCT(K), CRI between 80-85, conforming to LM79 and LM80 minimum 50000 hours life consisting to high/low voltage cut off, maintenance free isolated electronic driver with over voltage protection, surge protection and other saftey test as per IS 15885 Part-2/Sec 13, Low THD, PMMA grade high quality transmittance lens, Epoxy powder coated Die cast aluminium housing (Heat sink) with UV stabilized optics, polycarbonate LENS for symmetrical light distribution, weather proof gasket for lamp & driver compartment, Heat resistance toughened UV stabilized glass fitted in cast aluminium housing with SS screws, with External 10 KV surge protection and Internal 4 KV surge protection , SC,OC,OVand OT protections etcomplete all as specified and as directed.

Supply and fixing Bracket for street light fitting made of 40mm dia light grade GI pipe, 1.2 Mtr length bent to suitable shape for fixing of street light fitting with all necessary accessories Bracket, nuts, bolts, washers, two clamps made out of flat iron two pieces of size 40mmx06mmx500mm fabricated in shape and drilled holes for nuts and bolts all as specified and as directed.

Supply and fixing MS Box (Kiosk) weather proof made out of 16 SWG MS sheet of size 30cmx23cmx20cm including 04 strip three phase bus bar of aluminium strip with neutral link 32 Amp rating mounted on insulators of inflammable material and fix with 01 No MCB SP 240 Volts and current rating 06 Amp for controlling street light fitting to be mounted on poles at easily accessible height for repairing/replacement from ground with flat 40x6mm iron clamps and shutter to be opened/closed vertically with rachet ball locking system complete all as specified and directed by Engr-in-Charge.

Material and labour for cutting of PCC/hard standing/WBM road not exceeding 20 cm in width not exceeding 30 cm in depth for passing LT cable and making good of distrubed surface to match the existing sufaces by using old and new material i.e bitumen/PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) complete all as per specified & directed.

Total amount of Sch 'A' PART-X (SEC-II) (EXTERNAL ELECTRICAL SUPPLY WORK)

Total amount of Sch 'A' Part-XI (SITE CLEARANCE, EXCAVATION AND EARTH WORK)

NOTE: Amount against schedule of credit for retrieved materials mentioned under relevant part of Sch of Credit of tender document in PDF form will be deducted offline/manually from overall amount quoted by the lowest bonafide bidder during award of contract.