Military Engineer Services Tender

Removing excavated material n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

M&L Hard core of broken stone boulders of gauge n exc 63 mm, deposited spread and leveled in layers n exc 15 cm thick, watered and rammed to true surface complete all as specified and directed.

M&L 75mm thick PCC 1:4:8 Type D-2 (40 mm graded stone aggregate) as in sub-floor, sub-base, floor and pavings, etc, complete all as specified and directed.

M&L PCC 1:4:8 type D2 (40 mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L PCC (1:2:4) type B-0 (Using 12.5 mm graded aggregates), as in flooring 25 mm thick complete all as specified and directed

M&L brick work with old size sub class B brick straight or curved on plan exc 6 m mean radius built in cement mortar in CM 1:6 complete all as specified and directed.

M&L for preparation of steel and iron surface exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L RCC M-25 design mix using 20 mm graded stone aggregate in foundations, including rafts, footings, foundation beams, plinth beams, base for columns, etc basements slabs under rammed piles and mass concrete complete all as specified and directed.

M&L RCC M-25 design mix using 20 mm graded stone aggregate in Column, pillars, piers, posts and struts complete all as specified and directed.

M&L RCC M-25 design mix using 20 mm graded stone aggregate as in Beams cantilevers, bressummers lintels over 1.5 m span complete all as specified and directed.

M&L RCC M-25 design mix using 20 mm graded stone aggregate as in slab supported on walls, beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L Form work to sides of concrete foundations, footings, bases of columns, raft beams sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

M&L Form work to sides of pillars, posts, struts, piers, columns and stanchions rough finish surface of concrete square, rectangular or polygonal complete all as specified and directed.

M&L Form work to sides and soffits of floor or roof beam, haunching , lintels, cantilevers shelve including supports overhangs etc also splays between floors and beams, etc complete all as specified and directed.

M&L Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 20 mm thick (horizontal or sloping) complete all as specified and directed.

M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia as in stirrups complete all as specified and directed.

M&L TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hoping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified.

M&L rendering 10mm thick in CM 1:3 on fair faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified and directed

M&L rendering 15 mm thick in CM 1:6 on other than fair faces of brick work or concrete surface complete all as specified and directed.

M&L preparation of new plaster surface of walls and applying two coat of cement base paint camouflage pattern complete all as specified and directed.

S&F galvalume aluminum zinc coating Pre-painted GI based corrugated steel sheet 0.50mm thick having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F galvalume aluminum zinc coating Pre-painted GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L 6 mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame complete all as specified and directed

M&L 2nd class soft wood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm but bull nosed splayed chamfered or rounded on one edge or face complete all as specified and directed.

S&F Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles over 15mm thick screed bed or bedding layer in CM 1:4 for laying finishes,complete all as specified as directed by Engr-in- Charge and approved by GE.

M&L coloured chequered cement concrete tiles rubber mould anti fungal of 30cmx30cmx25mm thick , with grey cement any pigment set jointed and pointed in neat cement slurry in floors including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L Plain cement concrete M-10, 1:3:6, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm soft/loose soil complete all as specified and directed.

M&L cement concrete type C2 1:3:6 (40mm graded aggregate) as in mass concrete complete all as specified and directed.

S&F mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparation of surfaces treating ends of posts, backs of chowkats, etc area tarred exc 0.1sqm but n. exc 0.5 sqm each treated with tar or coal tar black paint complete all as specified and directed.

S&F 4mm dia galvanised steel wire,(Chain Link) 100x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed.

S&F MS bolts n exc 12 mm dia purpose made with hexagonal or square head one end and screwed the other, or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut not exc 30 cm long complete all as specified and directed.

S&F mild steel round bars 10 mm dia and over, cut of length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. (Fe-410) complete all as specified and directed.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing's and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

M&L Rendering 15 mm thick in cement plaster 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for applying 3 mm thick wall care putty on wall and ceiling including preparation new surfaces plastered or unplastered surfaces, complete all as specified .

M&L preparation of newly plaster surface and applying two coat of distemper oil emulsion white tinted complete all as specified and directed by Engr -in - charge.

S&F Rolled sections as in roof trusses, main and cross beams, hip and jack rafters, Purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates of Fe-410W (Gde -E-250 quality A) (framed) etc complete all as specified

S&F Stairs (framed) including stringers, treads, landing, balusters, hand rails etc. including cleats, brackets, etc of Fe-410-W(Gde-E-250 quality-A) (framed) etc,complete all as specified and directed.

M&L for painting two coat synthetic enamel paint over a pink primer in wooden surfaces of any description not otherwise described over 10 cm width or girth including preparation of new surfaces complete all as specified and directed.

S&F 2nd Class Hard wood plain, solid, straight chowkhats and frames wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S&F 2nd class hard wood plain framed panelled shutters (any number of panels) with panels of timber flat on both sides(feather edges) or of veneered particle board medium density, wood particle board with commercial face veneers 35mm thick, complete all as specified and directed by Engr-in -Charge

S&F 30 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass gauze etc (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc size of members of window/ventilator shutter etc are provide with style and rails as specified in SSR Part I, Section 8, clause 8.24 (b);fitted to chowkat, complete all as spd.

S&F butt hinges medium weight MS cold rolled 100mm long complete all as specified and directed.

S&F butt hinges medium weight MS cold rolled 75mm long complete all as specified and directed.

S&F aluminum anodized barrel tower bolt of extruded section of 150mm length complete all as specified and directed.

S&F aluminum anodized barrel tower bolt of extruded section of 125mm length complete all as specified and directed.

S&F aluminum handle 150 mm size, cast type, anodized complete all as specified and directed.

S&F aluminum handle 125 mm size, cast type, anodized complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt size 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and directed.

M&L 3 mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane including hacking out old glass panes all as spd

M&L Point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and including PVC casing and capping/Conduit medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size or PVC Gang Box all as directed by Engr in Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified. (Make of Cable : L&T/Polycab/Havells )

All as per srl item No-56 here in above but for one 3 pin 5A socket outlet independent controlled by one switch.

All as per srl item No-56 here in above but for one 5A socket outlet on the same board controlled by one switch.

All as per srl item No-56 here in above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead.

M&L for Switch Socket combination, 6 pin 5 and 15 amps multi purpose 2 in 01 flush type, 230 volts Make :Cona/SSK/ Anchor/Leader.

M&L for Switch Socket combination 2 in 1, 5 pin, 5 Amps flush type, 230 volts Make :Cone /SSK/Anchor/Leader.

S & F Lamp holder insulated body with back plate for batten fittings .Make of lamp holder -Cona/SSK /leader,

S&F decorative ultra slim linear LED 18 Watt 4' long lighting fixture with extruded al heat sink, environment friendly, energy efficient ready to use pack including LED tube complete with inbuilt electronic driver, PCB, connector block etc. including connecting up three copper flexible cable from ceiling rose to fittings including connecting up and fixed on including two nos PVC square box of required size complete all as specified & directed. Make: Havells/ Philips /Wipro

Supply & fixing ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified & directed by Engineer -in- Charge. Make: Anchor/ Cona/SSK

Supply and fixing MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 4 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed.

Supply and fixing MCB, SP, AC, 240 volts "B" series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed Make : Havells/ Legrand/Hager

Supply & fixing MCB, DP (Double Pole), AC, 240 volts, B series capacity 20 Amps to 32 Amps 10kA and making connections complete all as specified & directed Make : Havells/ Legrand/Hager .

Supply, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 16 Sqmm 4 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches/fixing on wall in PVC conduit pipe with the help of clamp/shadels,/binding with fencing /poles, complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. NOTE :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by 25%. (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.