Military Engineer Services Tender

Total Amount of Sch 'A' Part - III (Internal Water Supply)

Total Amount of Sch 'A' Part - IV (Internal Electric Supply)

Total Amount of Sch 'A' Part - V (Plumbing Work)

Total Amount of Sch 'A' Part -VI (Protective Work)

Total Amount of Sch 'A' Part -VII (Road, Path, Culvert and Hard Standing Work)

Total Amount of Sch 'A' Part -VIII (Sewage Disposal Work)

Total Amount of Sch 'A' Part -IX (Area Drainage Work)

Total Amount of Sch 'A' Part -X (External Water Supply)

Total Amount of Sch 'A' Part -XI (External Electric Supply)

Total Amount of Sch 'A' Part -XII (Construction of Igloos)

Total Amount of Sch 'A' Part -XIII (RCC track opening with RCC Retaining Wall)

Total Amount of Sch 'A' Part -XIV (Toe Wall, Steel Door, Fire Point, Hard Standing and RCC Static Water Tank)

Total Amount of Sch 'A' Part -XV (Demolition and Dismantling Work)

Sch 'A' Part -XVI (Misc Items of Work) Note : This Schedule is not Pre-Priced by MES and the Pre-Priced rate indicated as "Rs. 0.00" under col.5 signifies this fact only.

Supply, installation, commissioning and testing of flameproof EOT crane electrically operated on 3 phase 415 Volts over head crane of capacity 5 ton including electrical and mechanical parts, control panel, cable, double girder and DSL system, etc . The crane shall have electrically operated vertical and horizontal movement complete and shall be provided within the igloo including all accessories for lifting the goods, etc. The overhead crane (EOT crane) specifications are as under:- (a) Span = 9.5 mtrs (b) Capacity = 5 Ton (c) Power supply = 415 volts 3 phase at 50 Hz (d) Longitudinal traverse speed = 20 mtr/min (e) cross traverse speed = 15 mtr/min (f) Crane hoisting speed = 3.0 mtr/min (g) Hoist travelling height from floor of igloo = 5 mtr (minimun) (h) Bay length =36.5 mtr (i) Gantry girder for OEM bay length 36 mtr suitable of capacity 5 Ton EOT

Note:- The EOT crane shall also be provided with suitable capacities and no of squirrel cage motors including starters for main hoist -01 nos, Cross travel-01 no, long travel -02 nos with suitable VVFD drive, suitable control panel box including MCB/contactor/overload relay, push buttons station etc. Crane shall also be provided with suitable hydraulic thruster type BREAKING SYSTEM for main hoist cross travel and long travel . Drum couplings with suitable dia wire ropes of min tensile grade of suitable N/Sqmm connected with "C' SHANK type hook with safety latch shall be provided. Wheel -04 nos, 200mm dia for long travel and 160 mm dia for cross travel. PLATFORM with full length on each side of bridge girder with rubber cushioning shall be provided. Crane has to be provided with two coats of zinc chromite followed by two coats of golden yellow synthetic enamel paint. Note : Any other item like LT Cable of suitable size from control panel to bus bar of crane in steel cable tray etc required for smooth & efficient operation of the crane will be part of the item and no extra amount will be paid on this account. Make : Rockwell Hoisto cranes Pvt Ltd/Cranex Limited/Kone Cranes/ Dinesh enterprises

Earthing complete with galvanised mild steel earth plate electrode 60x60cmx6mm thick buried directly in ground preferably in vertical position (Earth pit not less than 2.25 mtr below ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised iron earth lead srip 32 x 6 mm by means of bolts, nuts, check nuts and washers of galvanised iron including PCC pit 1:2:4 type B-1 pre cast RCC cover slab of size 550x550x75mm with suitable built in handle made from 12mm dia MS round bar, excavation and earth work in any type of soil 20 mm dia bore medium grade galvanised iron water tubing fixed with cast iron funnel and wire mesh at one end and 40mm bore light grade galvanised iron protection pipe for earth lead strip upto 7.5m length, charcol, common salt complete all as shown in electric plate No 5 of SSR Part I connected to equipment complete all as specified and testing on completion.

Road safety convex mirror of size 450mm dia complete all as directed.

Supply installation, commissioning & testing , air cooled , Sound Proof Silent type, , diesel Engine driven Generating set 15 KVA (at 0.8 PF), 415 V, 3 phase, 4 wire engine as per IS: 10001/10002 and alteration as per IS: 13364, complete with control panel in an integral acoustic enclosure as per recommendations of latest CPCB norms, comprising of the following: Notes : Quoted rates shall be deemed to include:- (i) Supply of T and P and normal spare i.e. Bi-hexagonal ring spanner set of 12 pieces - 01 Set oil/fuel filters. (iii) Service maintenance manual along with cat part list and price list - 3 Set each (iv) Make of Engine and Alternator will be got approved from GE before placing the order a) DIESEL ENGINE : Diesel engine developing suitable BHP as per manufacurer recommendation , 1500 RPM inclusive of the following standard accessories:- (i) Radiator/heat exchanger cooling system (ii) Fly wheel (iii) Fly wheel housing complete with starter gear ring and coupling (iv) Fuel pipes (vi) Air cleaner

(vii) Fuel & Lub oil filter (viii) By pass filter (ix) Coolant inhibitor (x) Fuel pump (xi) Water pump (xii) Lub oil pump (xiii) Self/electric starter (xiv) Battery charging generator (xv) Industrial silencer (xvi) Lub oil cooler (xvii) Flexible pipe for silencer (xviii) Battery Volt meter (xix) Water temperature gauge, lub oil pressure gauge (xx) Speedo meter and engine running hours meter (xxi) Display for fault (b) ALTERNATOR :Synchronous alternator 3 Phase 4 wire, 50 cycles 1500 RPM , self excited, self regulated, brushless type, 0.8 PF, 415 V, AC supply, 15KVA capacity, copper wound, complete including necessary tools, mounted on strong rigid steel fabricated base frame and directly coupled through flexible coupling with diesel engine, complete all as specified. (c) CONTROL PANEL : Control Panel factory made of suitable capacity as per Original Equipment Manufacturer make & specification or as approved by OEM for DG Set of cap 15KVA of suitable size, consisting of following - (i) Contactor of suitable size for 15KVA DG Set. (ii) Copper bus bar of suitable current rating and sensitivity relay set unit with auxiliary CTs.

(iii) Electronic latch circuit with tripping indication . (iv) Re-set facilities. (v) 3 Phase MVR relay unit with single-phase protection complete with 2 No NC auxiliary contacts. (vi) 3 phase AVR relay unit complete. (vii) Self sequential starting relay unit 12 volts DC complete with alarm and power contactor. (viii) Electronic timer 220 volts for main contactor with 1 No NC auxiliary contactor. (ix) Electronic timer 220 volts for fuel cut off operation with 1 No NC auxiliary contactor. (x) Battery charging 12 volts 10 Amp complete with digital voltmeter and Amps meter, including trickle & boost charging, make as recommended by the manufecurer. (xi) Volt meter 0-500 volts panel mounting of size 96mm square with selector switch digital type. (xii) Amps meter 0-100 Amps with 3 Nos CTs, 400/5 and selector switch 96mm square digital type. (xiii) Frequency meter (45-55) Hz, 415 volt, 96 mm square digital type.

(d) Fuel tank of capacity as per manufacturer recommendations suitable for min 12 hrs continous run. (e) Base frame made out of suitable channel duly reinforced and provided with adequate numbers of anti vibration pads to ensure minimum vibration as recommended by manufacturer. (f) Battery maintenance free of 12 volts DC of suitabl AH as recommended by OEM , make as recommended by the manufacturer, along with the connecting leads and battery stand as per recommendations of manufacturer. (g) Acoustic enclosure with natural air circulation without loss of any power for ventilation fan. The enclosure shall be modular in construction with hinge. (h) Provision of PCC foundation as per manufacturer’s design & drawing / instructions. Foundation drawing will be vetted by GE before commissioning. (j) Accessories: All accessories and maintenance spares, battery with connecting battery leads and fastening, complete all as specified and as per the spare list with generator set.

LT Feeder Pillar Box floor mounted, out door type, dust and vermin proof, front & back,door openable, made out of MS Sheet 3.15 mm thick, duly powder coated, suitable for 3 Phase 4 wire, 415 Volts, 50 Hz, AC supply system, grounting the legs of panel in PCC foundation 1:4:8 and fixed 45 cm above the ground level complete as all directed suitable for and including the following. a).Copper bus bar, 3 Phase & neutral , 4 wire , AC Supply system 50 Hz mounted on epoxy based Post insulators, including drilling hole for cable connection, rating of bus bar 100 Amps. b). Incommer MCCB 4 Pole 440 Volts, 40 Amps 36 kA rating- 1 No c). Outgoing MCB SPN 32 Amps C series 220 Volts - 03 Nos(1 nos for Igloos,01 no toilet block and 01 spare) d). Outgoing MCCB FP 32 Amps 16 kA 415 Volts - 01 Nos(for crane) e ). Voltmeter suitable for 3 Phase 415 Volts supply system with inbuilt selector switch -1 No f). Ammeter 0-100 Amps 415 Volt with in built selector switch complete with CT of appropriate ratio.-1 No g). Indicator RYB . LED type 240 Volts- 1 Set. i). All accessories prewired with appropriate size copper strip or wire thimbles etc. All as required including foundation(including PCC and excavation) as directed by Engnr-in-Charge. Note : Earthwork and foundation deemed to be include in quoted rates.

Earthing complete with copper earth plate electrode 60x60cmx3.15mm thick buried directly in ground preferably in vertical position (Earth pit not less than 2.25 mtr below ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to copper earth strip 20mmx3mm by means of bolts, nuts, check nuts and washers of galvanised iron including PCC pit 1:2:4 type B-1 pre cast RCC cover slab of size 550x550x75mm with suitable built in handle made from 12mm dia MS round bar, excavation and earth work in any type of soil 20 mm dia bore medium grade galvanised iron water tubing fixed with cast iron funnel and wire mesh at one end and 40 mm bore light grade galvanised iron protection pipe for earth lead strip upto 7.5m length, charcol, common salt complete all as shown in electric plate No 5 of SSR Part I connected to equipment complete all as specified and testing on completion.

Construction of septic tank for 10 users (Brick construction) complete shown on drg No. CEUZ /TD-1585/2021 sheet 1/4 to 4/4 all as specified and directed.

Construction of soakage well (Brick construction) 1.2mtr dia and 3.0mtr deep below inlet pipe level (depth from inlet pipe to ground level 45cm), complete all as specified and shown on drg No. CEUZ/TD-1585/2021 sheet 1/4 to 4/4 all as specified and directed.

Flame proof LED bulk head light fitting 100 Watt, flame proof and water proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 66 protection with die cast aluminum housing with heat resistant toughened clear glass anti corrosive epoxy powder coated finish, complete with all accessories like flame proof flexible metallic conduit etc including connections all as specified and directed by Engr-in-Charge.

Flame proof cum weather proof distribution board 4 way including one incomer 32 Amps DP & 2 Nos MCB SP 16 Amps as outgoing made out of cast aluminium alloy LM-6, IP-55 with anticorrosive epoxy powder coated complete all as specified and directed.

Earthing complete with galvanised mild steel earth plate electrode 60x60cmx6mm thick buried directly in ground preferably in vertical position (Earth pit not less than 2.25 mtr below ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised iron earth lead 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron including PCC pit 1:2:4 type B-1 precast RCC cover slab of size 550x550x75mm with suitable built in handle made from 12mm dia MS round bar, excavation and earth work in any type of soil 20 mm dia bore medium grade galvanised iron water tubing fixed with cast iron funnel and wire mesh at one end and 15mm bore light grade galvanised iron protection pipe for earth lead strip upto 7.5m length, charcol, common salt complete all as shown in electric plate No 5 of SSR Part-I connected to equipment complete all as specified and testing on completion.

Water proofing treatment of joints of RCC wall structure, The following internal & External waterproofing treatment to joints of the walls is to be done: (a) Sand blast and water wash the internal & external side of the wall with high pressure water jet to remove loose concrete from the wall. Chiseling by hammer making V-Groove for a depth of 25mm on all cold construction joints (Horizontal joints & on both internal & External face) including the kicker joints to a minimum of 50mm, 25mm above & below the joints (to identify the joint which was not a straight line to clearly show the wall cast in lifts). fill with polymer modified mortar using FORSROC NITOBOND SBR@3ltr/Bag of cement in cement mortat (1:3) over priming coat as per manufacturer instructions & cure.

Top of roof slab and external faces of walls and the base slab of RCC structure shall be treated with two coat of chemical @3 Kg/Sqm in first coat and second coat. The chemical for water proofing shall be any one from dichtament DS of MC Bauchemic (India) Ltd, equivalent Pidilite (Dr fixit) chemicals or equivalent as approved by GE. The efficiency of treatment shall be observed by wetting the sides/ponding on roof continuously for 07 days before laying the filter media and earth filling. The chemical nafufill BB2 (liquid) @ 4% by wt of dichtament DS (Powder) shall be mixed in both the coats, complete all as specified and directed.

Point wiring for One light point/bell point/ceiling fan point/exhaust fan point controlled by one switch 5 Amp SP one-way complete with 1.5 Sq mm (nominal area) PVC insulated, unsheathed and multi stranded copper conductor FRLSH cable (ISI marked) drawn into and including PVC concealed conduit (medium duty) and conduit fittings including 1.5 Sq mm PVC insulated sheathed and multi stranded copper conductor FRLSH cable as earth wire to common earth and connecting to earth dolly etc complete all as specified and directed for one light point controlled by one way switch complete all as specified and directed.

Modular switch one way 6 Amps, 1 module, complete all as specified and directed.

Earth filling on top of roof 600mm thick exceeding 1.5m hight and up to 10.5 mtr from base complete all as specified. complete all as specified.

Supply only good soil from outside MoD land for traverse filling shall be properly graded material with no particle grater than 7.5mm in size and clay content less then 20% complete all as specified and directed.

Supply only (300mm thick) impervious silty soil from outside MoD land to prevent seepage of rain water (for roof filling) complete all as specified and directed

Labour only for separation/ screening any size of boulders from excavated soil, for screening of sieve size not grater then 7.5mm including stacking in separate heaps for measuring complete all as specified. Note: Rates for transportation of soil up to and including 250 mtr distance included in separation/ screening complete all as directed.

Deduction to be made from BOQ for Sch 'A' Part - XVII (Schedule of credit) Amount of Rs. 7,76,110.00 during AOC. Note: Tenderers shall not quote for this schedule.