Military Engineer Services Tender

M&L for Sand cushioning to cable with dry fine sand in trenches 8 cm below the cable and 15 cm above the cable after laying complete all as specified. Note : Punned thickness 18 cm will be measured and paid.

M&L for Bricks laid in trenches flat with width equal to length of brick for cable protection well burnt sub class 'B' laid across the cable complete complete all as specified and directed by Engineer-in-Charge. (ISO 001:2015 CERTIFIET)

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete all as specified and directed by Engineer-in-Charge.

Supply fixing in replacement laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 sq mm 3.5 core complete all as specified and directed by Engineer-in-Charge.

Supply, and replacement laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm 3.5 core complete all as specified and directed by Engineer-in-Charge.

Supply, laying, jointing and testing in trenches, galvanized iron steel tubing Light grade 80 mm bore (ISI marked) including provision of all necessary steel fittings/ accessories complete all as specified and directed by Engineer-in-Charge.

Supply, laying, jointing and testing in trenches, galvanized iron steel tubing Light grade 100 mm bore (ISI marked) including provision of all necessary steel fittings/ accessories complete all as specified and directed by Engineer-in-Charge.

S&F in connecting and testing change over switch 4 pole 415 volts on load of rating 100 Amp and including sheet enclosures complete all as specified and directed by Engineer-in-Charge.

Supply and replacement off load change over switch 415V in sheet metal enclosures 4 pole of capacity 160 Amps complete all as specified and directed by Engineer-in-Charge.

Supply, installation, commissioning and testing of LT Outdoor type panel board (factory made CPRI approved ) not less than 120cm x 100cm x 45 cm (LXHXW) Floor mounted DOUBLE DOOR outdoor TYPE made out of CRCA sheet 3.15 mm thick dust proof, powder coated from both side, individual door, factory locking system with two side ventilation suitable for working on 415 volt AC supply including bus bar chamber and Aluminium bus bar of capacity 250 Amps rating for phase and neutral mounted on hygroscopic insulator fixed in a separate bus bar chamber separate compartment for incoming and outgoing feeder prewired with suitable size of copper conductor cable including fitted on 50x50x6mm angle iron channel with PCC (1:3:6) bedding upto a height of 45cm above ground level and 30cm foundation complete all as specified directed by Engr- in- and provision of lugs and bushing for housing the following:- (i) Aluminium bus bar 250 amps for phase & neutral-04 Nos (ii) MCCB 4P 100 Amps, 25 KA - 01 No.(Incoming) (iii) MCCB 4P 63 Amps, 36 KA - 01 No. (Out going) (iv) MCB DP-20Amp-5,MCB DP-32Amp-5,MCB-DP-40Amp-2No,MCB-TPN-63Amp-3No,MCB-TPN-32Amp-2 v)Panel hud Have Additional space along with suitable din rail for mounting of 10 nos, SP/SPN (v) Multi functional digital Voltmeter and ampere meter including suitable and appropriate CTs-01 Set (vi) Indicator lamp (LED R-Y-B)- 01 Set

Supply, and replacement and installation, commissioning and testing of LT Outdoor type panel board (factory made of approved CPRI) not less than 120 cm x 100 cm x 60 cm mounted outdoor made out of CRCA sheet 3.15 mm thick dust proof, powder coated from both side, individual door, factory locking system with two side ventilation suitable for working on 415 volt AC supply including bus bar chamber and Aluminium bus bar of capacity 300 Amps rating for phase and neutral mounted on hygroscopic insulator fixed in a separate bus bar chamber separate compartment for incoming and outgoing feeder prewired with suitable size of copper conductor cable including fitted on 50x50x6mm angle iron channel with PCC (1:3:6) bedding upto a height of 30cm above ground level and 30cm foundation complete all as specified directed by Engr- in- and provision of lugs and bushing for housing the following:- (i) Aluminium bus bar 300 amps for phase & neutral-04 Nos (ii) MCCB 4P 200Amps, 36 KA - 01 No.(Incoming) (iii) MCCB 4P 100 Amps, 36 KA - 02No. (Out going) iv) MCCB 4P 32 Amps, 36 KA - 02 No. (Out going) (iv) MCCB 4P 63 Amps, 36 KA - 03 No. (Out going) (v) Multi functional digital Voltmeter and ampere meter including suitable and appropriate CTs-01 Set (vi) Indicator lamp (LED R-Y-B)- 01 Set

Supply, installing, testing and commissionning of CPRI approved LT panel outdoor type of size minimum 120cmx100cmx45cm (lengthxhieghtxwidth) double door or lager suitable size weather/vermin proof, made out of 3.15mm thick CRCA sheet duly powder coated, mounted on 65mmx65x5mm (ISA6565) iron angles frame of height 45 cm from PCC bedding, factory assembled compartmentalized construction, free standing type including 3 phase and neutral 200 amps current carrying capacity Aluminium bus bar with epoxy insulated coating with colour code and insulated support, cable galleries inter connecting bus bar connection/linkage complete and conforming to IS 8623 and IP 54 class of protection as per IS 2147 complete, including making connection of cables of incoming and outgoing with outgoing with thimble/lugs, including the accessories as below complete and mounting the panel on ground floor with PCC(1:3:6) bedding upto a height of 45 cm above ground level ground level complete all as specified and directed by Engineer-in-Charge. (a) aluminium bus bar 200 amps for 3 phases & neutral - 1set (b) MCCB 4 pole 63 amps 35 KA at 415 V - 1 No (Incoming) (c) MCCB 4 pole 40 amps 35 KA at 415 V - 1 No (outgoing) (d) MCB DP-20Amp-5, MCB DP-32Amp-5, MCB-DP-40Amp-2No, MCB-TPN-63Amp-3No, MCB-TPN-32Amp-2 (e)Panel shud Have Addictional space along with suitable din rail for mounting of 10 nos, SP/SPN

Supply,and replacement and installation, commissioning and testing of LT Outdoor type panel board (factory made of approved CPRI) not less than 100 cm x 90 cm x 60 cm mounted outdoor made out of CRCA sheet 3.15 mm thick dust proof, powder coated from both side, individual door, factory locking system with two side ventilation suitable for working on 415 volt AC supply including bus bar chamber and Aluminium bus bar of capacity 250 Amps rating for phase and neutral mounted on hygroscopic insulator fixed in a separate bus bar chamber separate compartment for incoming and outgoing feeder prewired with suitable size of copper conductor cable including fitted on 50x50x6mm angle iron channel with PCC (1:3:6)bedding upto a height of 30cm above ground level and 30cm foundationcomplete all asspecified directed byEngr- in- and provision of lugs and bushing for housing the following:- (i) Aluminium bus bar 250 amps for phase & neutral-04 Nos (ii) MCCB 4P 160 Amps, 36 KA - 01 No.(Incoming) (iii) MCCB 4P 100 Amps, 36 KA - 02No. (Out going) (iv) MCCB 4P 63 Amps, 36 KA - 02 No. (Out going) (v) Multi functional digital Voltmeter and ampere meter including suitable and appropriate CTs-01 Set (vi) Indicator lamp (LED R-Y-B)- 01 Set

Supply, installation, commissioning and testing of LT Outdoor type panel board (factory made of approved CPRI) not less than 100cm x 80cm x 60 cm mounted outdoor made out of CRCA sheet 3.15 mm thick dust proof, powder coated from both side, individual door, factory locking system with two side ventilation suitable for working on 415 volt AC supply including bus bar chamber and copper bus bar of capacity 200 Amps rating for phase and neutral mounted on hygroscopic insulator fixed in a separate bus bar chamber separate compartment for incoming and outgoing feeder prewired with suitable size of copper conductor cable including fitted on 50x50x6mm angle iron channel with PCC (1:3:6)bedding upto a height of 30cm above ground level and 30cm foundationcomplete all asspecified directed byEngr- in- and provision of lugs and bushing for housing the following:- (i) Copper bus bar 200 amps for phase & neutral-04 Nos (ii) MCCB 4P 100 Amps, 36 KA - 01 No.(Incoming) (iii) MCCB 4P 63 Amps, 36 KA - 02 No. (Out going) (iv) MCCB 4P 32 Amps, 36 KA - 02 No. (Out going) (v) Multi functional digital Voltmeter and ampere meter including suitable and appropriate CTs-01 Set (vi) Indicator lamp (LED R-Y-B)- 01 Set

Taking up/down existing 100mm bore cast iron pipe lines/water mains of any description and in position including fittings, accessories and fixtures etc existing in between pipe line, by taking out and opening any type of joints (Tyton/Gasket / Lead joints) complete all as specified and directed by Engineer-in-Charge.

Laying only in trenches, flanged cast iron pipes 100 mm bore of any description/grade and in any position (horizontal or vertical), as obtained from taking up or down, after making necessary addition / alterations and properly cleaning the pipes complete all as specified and directed by Engineer-in-Charge.

Supplying, laying, jointing & testing in repair in trenches or vertically at OHT cast iron pipes 100 mm bore with flanged ends vertically cast, class B, complete all as specified and directed by Engineer-in-Charge for the following size:- Note :-(i) Earth work, Joints and CI specials/fittings of the pipes shall be measured and paid for separately under appropriate item of Schedule `A'

Supplying and fixing cast iron specials/fittings such as bend, tee, socket, collar, reducer, nipple, tail pieces etc. suitable for spigot and socketed/flanged end pipe upto 150 mm bore complete all as specified and directed by Engineer-in-Charge.

Supply, installation, fixing, jointing and testing, ISI Marked, of approved quality, 100 mm bore cast iron sluice valve of class PN-1.6 conforming to IS-14846 of 2000 both ends flanged with iron wheel head and stainless steel spindle, long body type, jointed and tested including taking down old one complete all as specified and directed.

Supply and fixing, ISI Marked, of approved quality, size 100 mm bore cast iron non return valve, both ends flanged jointed and tested including taking down old one complete all as specified and directed for following sizes (Make Bir/Upadhayay/Sant as approved by GE ) Note :- (i) Joints of the non return valve shall be measured and paid for separately under appropriate items of Schedule ‘A’

S&F in repairs 10 Sqmm, 3 Core, flat submersible Cable, PVC insulated, PVC sheathed with multi-stranded copper conductors, 1100 Volt grade, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 16 Sqmm, 3 Core, flat submersible Cable, PVC insulated, PVC sheathed with multi-stranded copper conductors, 1100 Volt grade, complete all as specified and directed by Engineer-in-Charge.

S&F in replacement RCCB (residual-current device or Residual Current Circuit Breaker) safety device 63 A Single phase Breaker with short circuit/ leakage/ lightning supply complete all as specified and directed by Engineer-in-Charge.

S&F in repairs fully automatic Single phase preventer with suitable relay and suitable for 10 to 30 HP Submersible motor connected with, 415 volt, 50 HZ AC supply complete all as specified and directed by Engineer-in-Charge.

S&F in repairs fully automatic Phase adjuater/Phase corrector with suitable relay and suitable for 10 to 30 HP Submersible motor connected with, 415 volt, 50 HZ AC supply complete all as specified and directed by Engineer-in-Charge.

Supply and Errection of Out door Display P10 Module-Line Size 8x1ft, Data Interface through LAN/Wi-Fi/USB, Colour: Red LED Module Lines as per user programmable scrolling Number of character as per the requirement of the customer out door: Wall mount/ Pole Mount/ Roof Top Mount WITH Accessories and including all fittings, Brightness: 3500 nits,IP65 Water proof, High contrast ratio with a perfect louver/cove, Temperature and Humidity sensor measuring range: temp:-25 to+85 deg C, RH 0 to 100% OUT Put singnal: 4 to 20mA(0 to 100% RH) Terminal connections: soldering terminals for VCC, Analog out 4 to 20mA complete all as specified and directed by Engineer-in-Charge.

Supply and Errection of Out door Display P10 Module-Line Size 10x2ft, Data Interface through LAN/Wi-Fi/USB, Colour: Red LED Module Lines as per user programmable scrolling Number of character as per the requirement of the customer out door: Wall mount/ Pole Mount/ Roof Top Mount WITH Accessories and including all fittings, Brightness: 3500 nits, IP65 Water proof, High contrast ratio with a perfect louver/cove, Temperature and Humidity sensor measuring range: temp:-25 to+85 deg C, RH 0 to 100% OUT Put singnal: 4 to 20mA(0 to 100% RH) Terminal connections: soldering terminals for VCC, Analog out 4 to 20mA.

M&L For Earthing complete with galvanised steel earth plate electrode 600×600×6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth strip 25×4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed by Engineer-in-Charge.