Military Engineer Services Tender

Description all as per serial item No 3 above but except bricks complete all as specified and directed.

Demolition of cement concrete in ground floors and paving (unreinforced) including tiles pavings blocks if any n exc. 15 cm. thicknesses, below or above ground level, complete all as specified.

M&L for 100mm thick PCC 1:2:4 type B-1(Using 20 mm graded crushed stone aggregate) as in floor,hard standing surfaces finished even and smooth without using extra cement laid in alternate panel including use and waste of form work fair or rounding or chamfered of exposed edges all as specified and directed.

M&L for PCC 1:4:8 type D-2(40 mm graded stone agg) as Foundation, filling, mass concrete to foundation etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-1, (using 20 mm graded stone aggregate) as in bed blocks, coping, cills, steps, kneelers, bed plates, apex stones kerbs and similar work including necessary form work complete all as specified.

M&L for PCC 1:3:6 type C-2 (40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

M&L for extra for fair finished drain 30cm inner girth in cement concrete, using extra cement complete all as specified and directed.

Demolition of cement concrete in ground floors and paving ( reinforced) n exc. 15 cm. thicknesses, below or above ground level, complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (20 mm graded stone aggregate) as in slabs, similar suspended work including necessary form work etc complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (20 mm graded stone aggregate) as in wall, drain , retaining wall and similar suspended work including necessary form work etc complete all as specified.

M&L for precast RCC (1:2:4) type B-1 using 20 mm graded stone aggregate as cover slab fo man holes etc including form work complete all as specified.

M&L for TMT steel bars 10mm dia and over cut to length bent to shape required including crancking bending spirally for hooping to columns hooking ends and binding with mild steel wire (annealed) n. less than 0.90mm dia all as specified and directed.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, vertical or to batter etc complete all as specified.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering of 15 mm thick on fair faces of brick work or concrete surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

Removal of excavated soil not exc 50 m and depositing where directed at a level n. exc 1.5 m above the starting point all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.all as specified and directed.

Dismantling existing unservicable floor tiles of any description including bedding/screed layer all as specifed and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; all as specified and directed by Engr-in-Charge. Note:- Before execution of above mentioned item it is compulsary to make good the existing surface of PCC so that paver block could be fixed properly and no extra cost will be bourne by department.

M&L for precast cemented designer type tile any thickness and size also design,colour and pattern should be approved by GE set,jointed and pointed in net cement slurry in floors, and cut and,laid over 20 mm thick bedding layer of cement mortar 1:4 all as specified and directed by Engr-in-Charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. all as specified and directed by Engr-in-Charge.

Dismantling of wrought iron,mild steel work such as agle iron,flate and similar type work or any description not otherwise provided complete all specified and directed.

M&L mild steel sections confirming to FE-410-W as in Framed work as in doors, gates of angles or other section with gusset plates, rails etc including necessary cutting, drilling, welding etc complete all as per directed by Engr- in-Charge and any type of ornament pattern and design as approved by GE. Note:- 1.Contractor shall not have any claim in respect of design/Ornamental shape/designer member,the differnece of rate and amount of desinger pattern will not be paid by Department.

M&L for Preparation of new or untreated steel surface of any description exc. 10 cm. in width or girth and applying two coats of synthetic enamel paints, over a coat of red oxide zinc chrome primer, complete all as specified and directed by Engr-in-charge.

SCHEDULE 'A' PART-II (Schedule of credit) Credit amount of Rs (Refer schedule of credit) for retrieved material mentioned in Sch 'A' Part-II of Tender documents in PDF form will be deducted offline during acceptance of tender of lowest bidder.