Military Engineer Services Tender

M&L for Hardcore of broken stone, gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified.

M&L for Removing surplus soil to a distance not exe 50 mtr and depositing where directed at a level not exe 1.5 m above the starting point complete all as specified and directed.

M&L for Plain cement concrete M-5.0(1:5:10), type E-2 (using 40mm graded crushed stone aggregate), as in foundation filling and mass concrete in foundation, complete all as specified .

M&L for Brickwork with subclass ‘B’ bricks, old size bricks, straight or curved on plan exceeding 6.0mtrs mean radius built in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge.

M&L for Plain cement concrete Nominal Mix M-5 (1:5:10), type E-2 (using 40mm graded crushed stone aggregate), 75mm thick, as in sub base of floors, finish even to recive floor finishes, complete all as specified and as directed by Engineer-In-Charge.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces, in cement mortar 1:4,rendering is to be finished even and smooth (without using extra lime or cement), complete all as specified and as directed by Engineer-In-Charge.

Supply only integral water proofing compound.

M&L for Rendering 10mm thick on any type of surfaces, on ceiling, in cement mortar 1:3, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

M&L for Rendering 15mm thick, on any surface of brick or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-In-Charge.

M&L for Glazed ceramic tiles in vertical surface/ dado, size 300x200x6/7mm thick or 300x450x6/7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/ colour of tiles including laid over 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed.

M&L for Non-skid, coloured, ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including laid over screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge.

M&L Cement concrete M-15, type B-1, 1:2:4 ( using 20mm graded crushed stone aggregate) as in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, Krebs , water troughs and the like including weathering, slightly rounded or chamfered angles and throttling and necessary form work, all as specified.

M&L for Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-In-Charge.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed by Engineer-In-Charge.

M&L for Formwork to rough finish surfaces/ sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, Roofs, slabs, in pillers and pots, struts, piers columns, stanchion and similar work; vertical or to batter, complete all as specified and directed by Engineer-In-Charge.

M&L RCC M-25 design mix using 20 mm graded stone aggregate as in slab supported on walls, beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Granite (of any type) work (table rubbed and polished), 15-18mm thick, as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed by Engineer-In-Charge.

M&L for Plain cement concrete M-10(1:3:6), type C-1 (using 20mm graded crushed stone aggregate), 50mm thick, as in plinth protection and providing the joints throughout the thickness, filled with mastic filling comprising bitumen 85/25 grade and sand mixture 1:3 by weight, complete all as specified and as directed by Engineer-In-Charge.

S&F Factory made steel Ventilator, box type, using ERW hollow 'P' section, comprising double frame for and including gauged and glazed skeleton shutter with wire mesh and glass sheet 3.0mm thick, 4mm thick frosted glass jointed internally and made with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and as shown in drawing No- CEUZ/TD/1304, sheet No- 1/3 to 3/3 and as directed by Engineer-In-Charge. Note :- Cost of all items/elements eleborated in the specification and in Drawing shall be deemed to inlcude in quoted rate.

S&F Solid PVC Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing, including making good to disturbed surface of walls, complete all as specified and as directed by Engineer-In-Charge.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Paneling of plain colour PVC sheet to be fitted in the mild steel frame welded/ sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing in SSR, complete all as specified and as directed by Engineer-In-Charge.

S&F Butt hinges, size 100mm, medium weight, cold rolled mild steel, and fixed, complete all as specified and as directed by Engineer-In-Charge.

S&F Aluminium anodised, barrel tower bolts of extruded Section, size 200mm long and fixed, complete all as specified and as directed by Engineer-In-Charge.

S&F Aluminium handles, cast type, anodised, size 150mm, complete all as specified and as directed by Engineer-In-Charge.

M&L for Preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of chalk whiting, on plastered surfaces, preparatory to distempering, complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement paint , complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white washing, complete all as specified and as directed by Engineer-In-Charge.

S&F Vitreous China urinal, half stall, flat back, size of 465x355x265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern and flush pipe but including of waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe, , complete all as specified and as directed by Engineer-In-Charge.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand complete all as specified and as directed by Engineer-In-Charge.

S&F Low density polyethylene (LDPE) pipes of 32mm bore, pressure rating 6.0 Kgf/Sqcm), 900mm long, complete all as specified and directed by Engineer-In-Charge.

S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and as directed by Engineer-In-Charge.

S&F PVC connections 15mm size with brass nuts of length 450mm, complete all as specified and as directed by Engineer-In-Charge.

S&F Bib taps, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, complete all as specified and as directed.

S&F Angle valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe, complete all as specified and as directed.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore pipe, complete all as specified and as directed by Engineer-In-Charge.

S&F Tubes, 'medium grade' galvanized, 15mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-In-Charge.

S&F Tubes, 'medium grade' galvanized, 20mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-In-Charge.

S&F Stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 20mm bore pipe, complete all as specified and as directed by Engineer-In-Charge.

S&F Rotational moulded polyethylene water storage tanks of 500 liters capacity, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, complete all as specified and as directed by Engineer-In-Charge.

S&F Brass chromium plated, tubular towel rail, 20mm dia, D type, 60cm long between flanges, fancy type, complete all as specified and as directed by Engineer-In-Charge.

S&F Stainlees steel grating, chromium plated, size 125mm, heavy duty, complete all as specified and as directed by Engineer-In-Charge.

S&F PVC (SWR) bends of 75mm bore, pressure capacity not less than 4.50 Kgf/Sqcm, any radius, fixing with adhesive, complete all as specified and as directed.

S&F PVC (SWR) pipes, 75mm bore, pressure capacity not less than 4.50 Kgf/Sqcm, single socketed, in any length with rubber ring joints, laid in trenches/fixed to wall, complete all as specified and as directed by Engineer-In-Charge.

PVC (SWR) floor/Nahani trap of 75mm dia outlet, plain with grating including jointing with solvent cement, complete all as specified and as directed by Engineer-In-Charge.

S&F 75mm PVC (SWR) vent cowl, complete all as specified and directed

M&L 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including all fittings complete all as specified

M&L for Concrete bed to 110 mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, in PCC 1:4:8, type D-2, using 40 mm graded crushed stone aggregates.

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in any type of soil.

75 mm thick PCC 1:3:6, type C-2 using 40mm graded stone aggregates as in sub bases of floors and pavings.

M&L machine pressed precast concrete interlocking paver block of any size and shape confirming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and no pigment complete all as specified and directed

M&L 25mm thick sand filling under floor or in foundations or in floors including watering and consolidation

PCC 1:2:4, type B-1 using 20 mm graded crushed stone aggregates as in copings, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.2 M dia X 1.5 M effective depth

Providing precast cement concrete 1:2:4, type B-1 using 20 mm graded crushed stone aggregates as in cover slabs for manholes etc, set in cements mortar 1:6 .

S & f Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging of Fe 410-W(Gde E-250) quality-A; also fastening and fixing complete

M&L for Sand cushioning to protection of underground cables, laid 8 Cm before laying and 15 Cm after laying of cable, and punned to form an overall layer of 18 Cm thick, complete all as specified and directed by Engineer-In-Charge. Note: Punned thickness shall be measured.

Sub class ‘B’ bricks, modular size, brick covering laid dry, flat, transversally along the length of cable on sand cushioning for mechanical protection of cable, with width equal to the length of the brick, complete all as specified and directed by Engineer-In-Charge.

Supply, laying commissioning, testingof XLPE insulated ,screened ,pvc bedded galvanised steel strip or wire armoured ,electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 6.00 Sqmm 2 core complete all as specified and directed.

S&F tubes light grade, galvanised 25mm (1") dia for cable protection with all fittings and fixed complete to walls and ceilings or laid in floors/road crossing.

Supply and laying of steel water tubing of nominal bore 25 mm, medium grade galvanised with all fittings including short lengths, laid in trenches on fixed on walls complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.), complete, all as specified and directed

Supply and laying of steel water tubing of nominal bore 20 mm, medium grade galvanised with all fittings including short lengths, laid in trenches complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.), complete, all as specified and directed

Stop valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions of 25 mm bore complete all as specified and as directed.

Stop valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions of 20 mm bore complete all as specified and as directed.

Cutting and screwing existing steel tubing of size 50mm dia for alterations or lengthening screw on pipe to form connector and done in position without taking down, complete, all as specified and directed.

M & L for plain cement Concrete 1:3:6, Type C-2, using 40 mm graded crushed stone aggregate as in foundation filling and mass concrete complete all as specified and directed (for solar lights)

M & L for plain cement Concrete 1:2:4, type B-2 using (40mm) graded stone aggregates as in PCC coping of poles or for stays complete all as specified. (for solar lights)

M&L for Bricks, sub class B old size brick, laid flat, in floors in CM 1:6 and pointed

M&L for Keyed pointing in CM 1:4 complete all as specified and directed.

M&L preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L 1.6 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to sixe, holes puched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc, as required

Supply and laying GI medium grade pipe of 50 mm bore with union socket, bends, nipples etc for road crossing/entry of cables to buildings all as directed.

Supply and fixing LED flood light 210 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp.

M & L XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 4 core 16 Sqmm complete all as specified and directed by Engineer in charge.

M&L for Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 3 meter below ground level with top edge of the earth plate at a depth not less than 2.25 mtr below ground level earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers, all around top and bottom and electrode connection by using GI Wire 4 Sqmm (upto the body of equipment) by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles. GI pipe 20mm bore light grade for watering with funnel and wire mesh including medium grade GI Pipe 40mm bore protection and 40 mm GI pipe light grade for protection of strip. PCC chamber in cement concrete 1:3:6 type C-2 and RCC pit cover in M20 (design mix) complete all as shown in Electrical Plate No.3 of MES Standard Schedule of Rates (Part-I) of 2009 complete all as specified and testing on completion/. Note:- (i) The unit rate shall include for protection pipe, GI water pipe, wire mesh, funnel, excavation. RCC pit cover, test point, GI Wire 4 Sqmm from top of earth plate upto 5M above ground level and if GI protection is less than 5 meter, no price adjustment shall be made. (ii) If the testing result of earthing work is not been found satisfactorily then the contractor shall do other earthing work at his own cost and nothing shall be permissible on this account. (iii) Earthing work will be carried out in presence of MES representative.

Supply, Installation, Testing and Commissioning of all in one integrated LED solar street lighting luminaire with aluminium housing, UV stabilized polycarbonate cover, having minimum system lumen output of 3600 & system wattage not exceeding 36W, with system lumen efficacy not less than 120 lm/W. Luminaire has Integrated MPPT charger with Driver with charger efficiency 90% and should be available in CCT of 5700K. Luminaire should have highly safe & Advanced long life maintenance free Lithium ion Phosphate (LiFePO4) battery 12.8 V 24 Ah (BIS Certified) along with inbiult PIR sensor with dimming profile, with solar module capacity of 38Wp. Lifetime should be at least 50,000 burning hours at L70 at 25 degree centigrade and backup for 02 days, with and including galvanized steel pole 6 Meter long of size 50 mm dia, fixing light and any other necessary connected items for mounting on solar street light poles complete, all as per Manufacturer’s instructions and all as specified and directed by Engineer in charge. Note : Warranty Certificate for 5 years for complete system against manufacturing defects shall be attached with the purchase invoice from the manufacturer. (Excavation & earth work shall be measured separately)

Design, Supply, Installation, Testing and Commissioning of High Mast Light System of 16 Metre height continuously tapered, complete with its accessories shall be in two section with material as BS-EV10 025,S355 with cross section as 20 sided polygon, single dipping, hot dipped galvanised and suitable for wind velocity as per IS 875( Part 3) 1987 and only longitudinal weld confirming to BS 5153/AWS. Make: Bajaj / Wipro / Philips as approved by GE. The High mast shall be comprising of the following technical specifications : (a) High Mast shall have open raft shallow footing as foundation as per manufacturers design as per IS-456 and with 8 nos foundation bolts manufactured from special steel alongwith nuts, washers, anchor plates and templates. (b) An adequate door opening such that permit clear acces to equipments like winch, cable, wire rope, plug and socket etc. and also facilitates easy removal of the winch for servicing. The door opening shall be complete with a close fitting vandal locking alongwith provision for external locking arrengements . (c) The structure of high Mast shall be designed to sustain an assumed maximum reaction of wind speed at the height of 10 Mtr above ground level (i.e. 180km/hr). (d) It shall also include accessories for high mast includes R&L system with double drum winch self lubricating & sustaining type having lifting capacity of SWL 750 kg, head frame, steel wire rope 6mm dia (7/19 construction) galvanised Lantern Carrige suitable for fixing of 9 lantern LED flood light fittings, symmetrically fixed. (e) Integral power tool having input supply 3phase 415 volts, single speed, 1.5 KW REVERSABLE type and average operating speed of 2 mtr per minute. (f ) Fabricate, supply, install, testing and commissioning of LT out door total enclsoed LT panel board of suitable size as per OEM instructions totally enclosed made out of 3.15 mm thick CRCA sheet dust and vermin proof with front opening 440V 3 Phase 4 wire having 200 Amps capacity aluminium bus bar insulated wth sleeves, incoming MCCB TPN 100 Amps 440 Volts 25 KA - 01 No, MCCB TPN 63 Amps 440 Volts 25 KA - 01 No, cont...

item 81 cont.....'MCB SPN 20 Amps 440 Volts 10KA - 01 No, Reverse forward switch for automatic lowering/lifting of high mast light-01 No, Digital Ammeter, 96mmx96mm size, flush mounted, 0-200 Amps rating, with selector switch and CTs including all accessories- 01 No , Digital voltmeter, 96mmx96mm size, flush mounted, 0-500 Volts rating, with selector switch and all accessories- 01 No , phase indicator lamp LED type (RYB)-01 set of three and copper wiring with multistranded cable including timer switch electronic type 01 No with suitable contactors etc, cable glands, lugs, suitable control circuit for automatic switching on and off of the mast and two coats of synthetic enamel paint over a coat of red oxide primer and making necessary pedestal 300 mm height from floor level with as specified size of PCC Foundation work in M-15 type B-1 using 20mm graded stone aggregate for LT panel setup and angle Iron frame work in ISA 50x50x6mm etc and making connection.cont....

item 82 cont.......(g) Provn of single trailing cable 1100 volts grade with flexible copper conductor EPR insulation PCP sheathed min 6 sqmm X 10 cores suitable for 09 luminaries or independent electric connection for each luminarie complete all as specified and directed. (h) Provn of single pointed air termination rod and necessary fitment required for protection against lightning protection. (j) LED AVIATION lights TWIN type with polycarbonate diffuser & cast aluminium housing IP 65 (k) Weather proof hinged opening with locking arrangement at bottom of the mast for installation of winch and electric panel as per manufacturer recommendations. (l) Foundation RCC including design as per instructions of manufacturers recommendations suitable for 15 mtr high mast with accessories as detailed in respective items. NOTES: (i) Rate quoted against this item deemed to be included testing & commissioning of above high mast system. (ii) Excavation, earth work and PCC work of requisite grade and depth of foundation against High Mast Lights as per Manufacturer's instructions shall be deemed to have been quoted in quoted rates by contractor and nothing shall be paid seperately on this aspect. (iii) The quoted rate shall deem to be included all other accessories not specified above required for complete functioning of high mast lighting system. (iv) High Mast shall be installed under guidance of manufacturer's instructions.