Military Engineer Services Tender

M & L for Cement concrete type B- 2, 300mm thick 1:2:4 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

Excavating in post holes in hard/dense soil (or similar holes) each n exc 0.5cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n exc 25cm, watering and removing surplus soil to a distance n exc 50m and making good surface, complete all as specified and directed.

S&F for roof trusses (framed), trussed, purlins, rafters, crane gantries, rails and fastenings and heavy brackets framing (beam, tee, angle, channel or flat sections) of Fe-410-W (Gde-E-250) quality A, including distance places, cleats etc., complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based plain mild steel sheeting 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters, drip and straight flashing (length and girth as fixed), complete all as specified and directed.

M & L for Preparation of new or untreated surface of iron and applying two coats of synthetic enamel paint over and incl a coat of red oxide primer complete all as specified and directed.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in Hard and dense soil complete all as specified & directed.

Returning, filling in excavated soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified & directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified & directed.

M&L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm & n exc 20cm in width type C1,1:3:6 using 20mm graded crushed stone aggregate and setting in mortar 1:4, complete all as specified and directed.

M&L for rendering 15mm thick (1:4) on fair faces of brick work or concrete surfaces even and smooth (without using extra cement) complete all as specified & directed.

M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement, complete all as specified and directed.

M & L for preparing new plastered or unplastered surfaces of wall and applying three coats of white wash complete all as specified & directed.

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; framed balusters; railings; conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

M & L for PCC 1:4:8 type D-2, 100mm thick, using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M & L for PCC 1:2:4 type B-1, 25mm thick, using 20mm graded crushed stone aggregate as in surface of flooring complete all as specified and directed.

M & L for 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specified and directed.

M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick with grey cement and pigment set and jointed in neat cement slurry and pointed in white or coloured cement complete all as specified and directed.

M & L for providing cement concrete cast in situ 1:2:4, type B1 (using 20mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edge including use of formwork, complete all as specified and directed.

M&L for point wiring using approved colour coding as per IS with using approved colour coding as per IS 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continuous earthing in & incl PVC Conduit with accessories having ISI mark fixed on wall surfaces / ceiling including provision PVC Box on top for fixing switches sockets etc. all as specified for one light point/ fan /Bell point controlled by one switch complete all as specified and directed by Engineer-in-Charge.

All as per item No 24 here-in-before but for one multipin socket outlet 15 Amp, on independent board, using 2.5 Sqmm copper conductor cable, complete all as specified and directed.

Supply and fixing of switch piano type 5 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge.

Supply and fixing of switch piano type 15 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge.

S & F of socket outlet multi pin 15 Amp 230 Volt flush type complete all as specified and directed.

Supply and fixing surface & wall mounted LED 20W tube light fitting 4 feet with high quality material and design, extruded aluminium housing enhances safety. High quality PC diffuser, reliable and robust housing structure, maximize the endurance over the life time slim integrated design, easy to install efficacy 125 limen/ watt along with all accessories complete all as specified and directed by Engg-in-Charge.

Supply and fix ceiling rose 3 terminal PVC/polycarbonate, isolated body complete all as specified and directed.

Supply, laying, commisisioning and testing cable XLPE insulated IS 7098(part-i)-1988, ISI marked screened, PVC sheathed, steel armoured electric power cable (heavy duty) with aluminum stranded conductor for working voltage upto and including 1100 volts, cross sectional area of cable 10 sqmm 4 core laid in trenches /fixed on pole/wall/passed through pipe/cutting of road with making good wherever required as per site including jointing and testing complete all as specified & directed.

M & L for Sand cushioning for under ground cables, the trenche shall be provided with a layer of sand 8 cm deep before laying the cable and with a layer of 15 cm depth after laying and straightning of cable and then gently punned down to a depth of 10 cm above the top of the upper-most cable, complete all as specified and directed. Note: Punning shall be done by hand; mechanical punners shall not be used.

M&L for laying dry old size with subclass 'B' made of burnt clay best quality locally available with permissible tolerance, laid straight in trench for protection of cable complete all as specified and directed.

M&L for Earthing complete with GI steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI earth wire of 4 mm dia protected by GI protection pipe light grade of 40mm bore dia from mechanical injury, 20 mm medium grade for watering with funnel, including test point up to 7.5 meter from earth pit, adequate quantity of common salt, charcoal dust, chemical and connected to test point by means of bolts and nuts washers made out of GI all as shown in Electrical plate No 3 of SSR part I including necessary earthwork and excavation in any type of soil, PCC 1:2:4 type B1 chamber with 40mm thick RCC 1:2:4 type mix cover slab with 6mm dia MS bars at 100mm dia both ways with MS hook 6mm dia MS bars etc. complete all as specified and directed by Engr-in-charge. Note: 1. Suitable quantity of charcoal, common salt, funnel, GI pipe required for watering, pit & CI pit cover etc is deemed to be included in quoted rate and lead wire used beyond 7.5m from pit cover will be measured separately. 2. On testing after completion if the desired resistance is not obtained the earthing shall be re-done at no extra cost.

Supply and fixing of sheet metal enclosure double door for DBs TPN for 12 way 415 volt complete all as specified and directed by Engineer-in-Charge.

S&F of MCCB FP 63 Amp,16 KA, 415V confirming to IS/IEC:60947-2, complete all as specified and directed by Engineer-in-Charge.

S&F MCB TPN 6-32 Amp, 10 KA in accordance with IS/IEC:60947-2 & 60898-1, 415V, 50 Hz, complete all as specified and directed by Engineer-in-Charge.

S&F MCB SP 6-32 Amp, 10 KA in accordance with IS/IEC:60947-2 & 60898-1, 240V, 50 Hz, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply and fixing of PVC Terminal /junction pole box, 4 pole strips, mounted on DMC insulator and MCB SP 6 Amps, 10 KA, Size 310 x 210 x 120mm and fixed with MS flat iron clamps to pole complete all as specified and as directed.

S&F bracket made of GI pipe light grade 40mm bore bend to shape in 120 degree of 1.2 m in length suitable for fixing street light luminaire and fixed on wall/pole including necessary MS clamps, nuts, bolts etc complete all as specified and as directed.

Supply and fix of 2 runs of 1.5 Sqmm PVC FRLS insulated stranded copper cable for connection of street light including PVC conduit 20 mm external dia, fixed on pole with proper clamping/ saddling etc. complete all as specified and directed.

Supply, Installation, Commissioning and Testing of Automatic Organic Waste Composting Machine with inbuilt Organic Waste Shredder Machine, Incl All fittings /Fixtures/accessories required, complete all as specified and directed by Engineer-in-Charge. Note:- (a) Capacity - 50Kg/Day (b) Inputs - Food waste, Garden waste and all types of organic waste. (c) Outputs - Organic bio fertilizer. (d) Biomass retention period is 4 to 5 Days. (e) Power supply 3 phase ,50Hz, 415/440 Volts. (f) Inbuilt Shredder. Material:- Waste mixing chamber/composting tank -SS304 Mixing Blade-SS304 Shredder shaft, blade and frame-SS304

Material and Labour for Comprehensive Warranty / AMC of the Automatic Organic Waste Composting Machine of capacity 50 Kg/Day complete as mentioned below from the date of completion of the work:- (a) Two years replacement warranty from the date of completion of the work incl AMC (all machine parts, cleaning included). (b) After warranty, comprehensive AMC for a period of three years of the complete system. All as specified and directed by Engr-in-charge.

Supply and Fixing of heavy duty HDPE 120 Ltr wheel Manual lift garbage Dustbin with lid, complete all as specified and directed by Engg-in-Charge.