Military Engineer Services Tender

Supply and erecting steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-55 (11.0 metres long) conforming to IS-1678 and including marking alternate 05 Nos white and black strip 30cm height with two coats of synthetic enamel paint including preparation of surfaces, upto 1.5 metre above the coping of pole, starting with black strip, including dismantling and taking down of old unserviceable steel tubular HT pole complete all as specified and directed. Note: Excavation and earth wok and PCC for foundation, channel, clamps nuts, bolts to be measured and paid separately.

Supply and fixing of lightning arrestor, expulsion type, suitable for 11000 volts, with all fittings, trasmission class, discharge capacity 65 KA, including connecting with HT line complete all as specified and as directed.

Material and labour for earthing complete galvanised earth plate electrode 600mm x 600mmx 6.00mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 32x6 mm GI strip earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire protected by galvanized steel pipe 40mm dia (light grade) and connected to main switch or main control board all as shown in electrical plate No.3 of SSR Part-I & including necessary excavation and earth work. The rate also include charcoal & salt in alternate layers, 20mm dia GI pipe (light grade) for watering and 40mm GI protection pipe, funnel, wire mesh, cast iron cover and frame etc, complete, all as specified or indicated and as directed including testing on completion. all as specified and directed.

Material and labour for earthing complete with galvanised earth plate electrode 600mm x 600mmx 6mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 4.00 mm wire earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire protected by galvanized steel pipe 15mm dia (light grade) and connected to main switch or main control board all as shown in electrical plate No.3 of SSR Part-I & including necessary excavation and earth work. The rate also include charcoal & salt in alternate layers, 20mm dia GI pipe (light grade) for watering, protection pipe, funnel, wire mesh, RCC cover etc, complete, all as specified or indicated and as directed including testing on completion. Notes for item No 6 & 7 :- (i) The unit rate shall also included for earth work in hard/dense soil, PCC (1:3:6) type C1 chamber, RC 1:2:4 type B-1 cover 50mm thick reinforced with 8mm dia CTD bars @ 150mm c/c both ways, funnel with GI watering pipe 20mm dia light grade, GI protection pipe light grade 40mm dia and wire mesh complete, specified on Sl Page No 389 of SSR Part-II.(ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. (iii) The quoted rate shall include the cost of earth pit covers to be conspicuously marked of plate with stand grouted in PCC.(iv) On testing after completion if the desired earth resistance is more than 2 ohm the earthing will be redone at no extra cost.

Supply and fixing of Retro reflective sign board of size 600 x 600 mm made of ACP sheet of 3mm thick ACP sheet shall be fixed on MS frame with legs of MS angle section 35mm X 35mm X 4mm grouted in PCC 1:3:6 type C-1, 800mm above the ground level and 600mm below the ground level. The background of board to be provided with green colour, letters and border with white retro reflective tape. Same description shall be mentioned on both sides of ACP sheet complete all as specified and directed. NOTE:- (i) Excavation, earth work, PCC, nuts, bolts, fasners, paint on MS frame and legs shall be included in quoted rates by contractor. (ii) The size of letters and description shall be all as per sample approved by Engr-in-Charge.

Supplying and laying of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) with aluminium conductor, 11000 Volts grade, cross sectional area 95 Sqmm 3 core, suitable for 11 KV earthed system confirming to IS 7098 Part - 2 for insulation and for conductors Class 2 to IS 8130 - 84, in trenches, floors, ducts passing through pipe for road crossing etc., complete all as specified and directed. Note : Excavation, earth work, cable cover protection, sand cushioning and GI pipe etc shall be measured & paid for separately.

Supplying and laying XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) with aluminium conductor, 1100 Volts grade, cross sectional area 240 Sqmm 3.5 core, suitable for 1.1 KV earthed system, in trenches, floors, ducts passing through pipe for road crossing etc, including connecting and testing complete all as specified and directed. Note : Excavation, earth work, cable cover protection, sand cushioning and GI pipe etc shall be measured & paid for separately.

Supplying and laying XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) with aluminium conductor, 1100 Volts grade, cross sectional area 70 Sqmm 3.5 core, suitable for 1.1 KV earthed system, in trenches, floors, ducts passing through pipe for road crossing etc, including connecting and testing complete all as specified and directed. Note : Excavation, earth work, cable cover protection, sand cushioning and GI pipe etc shall be measured & paid for separately.

Supplying and laying XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) with aluminium conductor, 1100 Volts grade, cross sectional area 50 Sqmm 3.5 core, suitable for 1.1 KV earthed system, in trenches, floors, ducts passing through pipe for road crossing etc, including connecting and testing complete all as specified and directed. Note : Excavation, earth work, cable cover protection, sand cushioning and GI pipe etc shall be measured & paid for separately.

Supplying and laying XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) with aluminium conductor, 1100 Volts grade, cross sectional area 35 Sqmm 3.5 core, suitable for 1.1 KV earthed system, in trenches, floors, ducts passing through pipe for road crossing etc, including connecting and testing complete all as specified and directed. Note : Excavation, earth work, cable cover protection, sand cushioning and GI pipe etc shall be measured & paid for separately.

Supplying and laying XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) with aluminium conductor, 1100 Volts grade, cross sectional area 16 Sqmm 4 core, suitable for 1.1 KV earthed system, in trenches, floors, ducts passing through pipe for road crossing etc, including connecting and testing complete all as specified and directed. Note : Excavation, earth work, cable cover protection, sand cushioning and GI pipe etc shall be measured & paid for separately.

Material and labour for cable end termination jointing kit, HT 11 KV, earthed system (cold shrinkable), outdoor type joint complete with jointing material and accessories suitable for HT XLPE cable of size 95 sqmm, 3 core, 11 KV grade, earthed system complete all as specified and as directed.

Material and labour for cable jointing kit for 1.1 KV grade cable for outdoor termination, heat shrinkable joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 240 sqmm complete all as specified and as directed.

Material and labour for cable jointing kit for 1.1 KV grade cable for outdoor termination, heat shrinkable joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 70 sqmm complete all as specified and as directed.

Material and labour for cable jointing kit for 1.1 KV grade cable for outdoor termination, heat shrinkable joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 50 sqmm complete all as specified and as directed.

Supply, installation and testing of LT Panel of size (1.5 mtr X1.2 mtr X0.50 mtr) , weather proof, outdoor type,degree of protection IP-56, having thickness of 3.15mm and inner shell made out of 2mm thick CRCA sheet and MS angle size 50x50x6 mm mounted on PCC 1:2:4 type B-1 platform size 1.50X0.8X0.30M and 60 cm above and 45 cm below the ground level, frame factory fabricated with front openable double door system and door madeup in 60-70% perspex sheet of minimum 5 mm thick and cable alloy (Each door hinged with body at 3 places with body and hinges should be welded with body and door) lockable/open able by Keys having chromium plated 19 mm dia fancy lock, “U” type gasket shall be used to make the outer shell completely vermin proof suitable for 3 phase 4 wire 415 Volt, 50 Hz, tested at factory approved from CPRI factory fabricated having modern fabrication and testing process followed by powder coat painting having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof and general construction confirming to IS:61439/2011 Part-1 and part -2 type test certificate with not less than IP-56 and breaking capacity 65 KA complete comprising of the following :- (a) Aluminium busbar of capacity 400 Amps 03 Nos for three phase and 01 nos 200 Amp for Nuetral. (b) Incomming :-MCCB 250 Amps, 4Pole, 25 KA adjustable type - 01 No (c) Outgoing :- MCCB 100 Amps, 4Pole, 415V,16 KA - 04 Nos. (d) LED indicator lamps RYB - 01 Set of three (e) Multi function meter with KWH, Voltage, Amp, frequency meter 01 Nos (f) Misc items like screws, cable tie, complete wiring with copper cable 1.5/2.5 Sqmm, cable lugs, sleeves and glands for incoming cable etc complete all as specified and directed.

Supply, installation and testing of LT Panel of size (1.0mtr X0.9mtr X 0.50mtr) , weather proof, outdoor type,degree of protection IP-56, having thickness of 3.15mm and inner shell made out of 2mm thick CRCA sheet and MS angle size 50x50x6 mm mounted on PCC 1:2:4 type B-1 platform 1.0x0.60x0.30M and 60 cm above and 45 cm below the ground level, frame factory fabricated with front openable double door system and door madeup in 60-70% perspex sheet of minimum 5mm thick and cable alloy (Each door hinged with body at 3 places with body and hinges should be welded with body and door) lockable/open able by Keys having chromium plated 19 mm dia fancy lock, “U” type gasket shall be used to make the outer shell completely vermin proof suitable for 3 phase 4 wire 415 Volt, 50 Hz, tested at factory approved from CPRI factory fabricated having modern fabrication and testing process followed by powder coat painting having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof and general construction confirming to IS:61439/2011 Part-1 and part -2 type test certificate with not less than IP-56 and breaking capacity 65 KA complete comprising of the following :- (a) Aluminium busbar of capacity 200 Amps 03 Nos for three phase and 01 nos 100 Amp for Nuetral. (b) Incomming :-MCCB 100 Amps, 4Pole, 25 KA - 01 No (c) Outgoing :- MCCB 63 Amps, 4Pole, 415V,16 KA - 01 No. (d) MCB 40 Amp, TPN, 'B' type 240 V, - 03 Nos (e) LED indicator lamps RYB - 01 Set of three (j) Multi function meter with KWH, Voltage, Amp, frequency meter 01 No. (j) Misc items like screws, cable tie, complete wiring with copper cable 1.5/2.5 Sqmm, cable lugs, sleeves and glands for incoming cable etc complete all as specified and directed.

Supply, installation and testing of LT Panel of size (1.0mtr X 0.9mtr X 0.50mtr) , weather proof, outdoor type,degree of protection IP-56, having thickness of 3.15mm and inner shell made out of 2mm thick CRCA sheet and MS angle size 50x50x6 mm mounted on PCC 1:2:4 type B-1 platform of size 1.0x0.9x0.3M and 60 cm above and 45 cm below the ground level, frame factory fabricated with front openable double door systemand door madeup with 60-70% perspex sheet of min 5mm thick and cable alloy (Each door hinged with body at 3 places with body and hinges should be welded with body and door) lockable/open able by Keys having chromium plated 19 mm dia fancy lock, “U” type gasket shall be used to make the outer shell completely vermin proof suitable for 3 phase 4 wire 415 Volt, 50 Hz, tested at factory approved from CPRI factory fabricated having modern fabrication and testing process followed by powder coat painting having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof and general construction confirming to IS:61439/2011 Part-1 and part -2 type test certificate with not less than IP-56 and breaking capacity 65 KA complete comprising of the following :- (a) Aluminium busbar of capacity 100 Amp - Set of 4. (b) Incoming :-MCCB 63 Amps, 4Pole,16 KA - 01 No (c) Outgoing :- MCB 32 Amps, 'B' Type, TPN 4P, 240V,- 07 Nos (e) LED indicator lamps RYB - 01 Set of three (f) Multi function meter with KWH, Voltage, Amp, frequency meter 01 No. (g) Misc items like screws, cable tie, complete wiring with copper cable 1.5/2.5 Sqmm, cable lugs, sleeves and glands for incoming cable etc complete all as specified and directed.

Material and labour for hardcore of broken bricks filling of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

Excavating in post holes or similar holes, each not.exceeding 0.5 cu mtr, getting out, in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and directed.

Material and labour for PCC 1:3:6 type C-2 (using 40 mm graded mechanically crushed stone aggregate), as in post holes, complete, all as specified and as directed.

Supply and fixing of rolled mild steel angle iron posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary welding, drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165 etc. complete all as specified and directed.

Material and labour for mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, dia of shank 5 to 10mm and length of bolt exceeding 5cm and not exceeding 10cm complete all as specified and directed.

Supply only 4 / 5mm dia galvanised mild steel wire chain link fencing of mesh size 50 to 100mm, complete all as specified and directed. Note:- The weight of chain link fencing shall be ascertained by BOO to be detailed by GE.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. with and including MS binding wire complete all as specified and directed.

Material and labour for mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips 10mm dia round bars confirming to Fe 500/550 D as in stiffeners to chain link fencing complete all as specified and as directed.

Material and labour for preparation of new steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint, over a coat of red oxide zinc crome primer complete all as specified and as directed.

Material and labour for brick work, using sub class ‘B’ bricks, straight or curved on plan to any radius, exceeding 6mtr mean radius, built in cement mortar 1:6 complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B-0 (using 12.50 mm graded mechanically crushed stone aggregates) as in coping and the like, finishing the surface fair and even, including necessary form work, complete, all as specified and as directed.

Material and labour for hand packing (any thickness) with broken stone or boulders at back of walls over arches etc. and raising (or lowering) to the required level including necassary ramming and watering complete all as specified and directed.

Material and labour for 100 mm thick PCC (1:2:4) type B-1, using 20 mm graded mechanically crushed stone aggregates, as in floor, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finishing the surface fair and even smooth without using extra cement complete all as specified as directed.

Material and labour for preparation and applying three coats of white wash on newly plastered surface of wall complete all as specified as directed.

Material and labour for drilling hole of any size manually as per site requirement, drilling for laying pipes under the road for crossing electrical cable complete all as specified as directed.

Disconnecting & taking out old/ defective LT Panel any size and any type from it's foundation on floor and after removal, LT panel should be deposited in MES storecomplete all as specified as directed.

Supply and fixing of GI tubing, 80mm bore, light grade, on poles/on walls/under floors/ road crossing as required at site complete all as specified and directed.

Supply and fixing of GI tubing, 50mm bore, light grade, on poles/on walls/under floors/ road crossing as required at site complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation, shafts, man holes,for under ground cable / erection of poles, stays, locating fault of LT Cable and stay assembly and in other situation not exceeding 10 Square metre on plan and getting out in any type of soil including dressing/trimming of sides and leveling, grading and ramming of bottom of excavation complete all as specified and as directed.

All as per item No. 41.00 here-in-before but depth exceeding 1.5 metre & not exceeding 3.0 metre complete all as specified and as directed.

Returning, filling in, in soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick each layer complete all as specified and directed.

Removing excavated material/soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Material and labour for Sand cushioning to cable with a layer of sand 8 cm deep before laying the cable and 15 cms deep after laying the cable (punned down to 18 cms depth after laying and stretching of cable ) complete all as specified and as directed. Note:- Punned thickness 18cm shall be measured for payment purposes.

Material and labour for PCC 1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregate), as in foundation filling and mass concrete, complete, all as specified and as directed.

Material and labour for PCC 1:3:6 type C-2 (using 40 mm graded mechanically crushed stone aggregate), as filling and mass concrete, complete, all as specified and as directed.

Material and labour for PCC 1:2:4 type B1 (using 20 mm graded mechanically crushed stone aggregate), as foundations to poles including necessary form work and finishing the exposed surface even and smooth with out using extra cement complete all as specified and as directed.

Material and labour for cross arms,bracings, supports, clamps and back plates fabricated from structural steel section including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape of size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and as directed.

Supply and laying of un-reinforced precast concrete cable cover ,class HV, type-1 with peak, size 300X180X40mm complete all as specified and directed.

Supply and laying of un-reinforced precast concrete cable cover ,class LV, type-1 with peak, size 250x150x40mm complete all as specified and directed.