Military Engineer Services Tender
If you want to inquire about any e-tender the Haryana government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Haryana tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Haryana etender you're looking for. Read further to learn how to search and bid for etender Haryana.
Costs
EMD
₹ 1,66,525Document Cost
₹ 1,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_681248_1Tender No
CWE/CHM-83/2024-25Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
M&L for Reinforced Cement Concrete 1:2:4 type B-1 (using 20 mm graded stone aggregates) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engineer-in-Charge.
2
-
-
M&L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge.
160
-
-
M&L for formwork to soffits of suspended slabs such as lintel, roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete complete all as specified and as directed by Engineer-in-Charge.
24
-
-
Dubbing out average 10 mm thick CM 1:4 on irregular face of walls complete all as specified and as directed by Engineer-in-Charge.
60
-
-
M&L for Rendering 15 mm thick, in cement mortar 1:4 on brick or concrete surfaces with WPC (paid separately) finishing fair & even without using extra cement complete all as specified and as directed by Engineer-in-Charge.
60
-
-
Cutting down small trees/ bushes from wall/ roof/ chajja of building including digging out the roots from brick work or any other structure portion of building including applying root killer chemical as per manufacturer instructions and making good the disturbed portion to match the existing surface complete all as specified and as directed by Engineer-in-Charge.
30
-
-
M&L for disconnecting of PVC tank of capacity 500 Litres & upto 1000 Litres for cleaning including setting aside temporarily and refixing later in same position to enable water proofing treatment of roof slab beneath the tank in following laid down process all as specified and directed :-
a) Dewatering & removing all settled silt, scale & dust from inside of tanks using coconut brush manually and applying bleaching powder and allowed to rest for 1 hour.
b) Cleaning & rinsing the tank using fresh water to wash out complete and allowed to dry for 30 minutes.
c) Writing letters of 7 cm height using synthetic enamel paint (white colour) to mention date of cleaning including rubbing out old letters written over the tank.
d) Refixing the tank & old fittings in same position or raised/ lower height after cleaning or water proofing treatment (as may necessary) complete all as directed by engineer-in-Charge.
6
-
-
Note :- Alternative arrangement for providing water supply to the Qtr shall be provided by the contractor by relocating the serviceable tank until the waterproofing treatment is completed.
-
-
-
Dismantling Brick tiles or terracing tiles, single layer on roofs complete all as specified and as directed by Engineer-in-Charge.
640
-
-
Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and as directed by Engineer-in-Charge.
48
-
-
Roughening the surfaces of old concrete roof surfaces & sides by picking, brushing with wire brush, sweeping clean and washing down with water to remove dust etc., brushing neat cement slurry with 3.0 kg of cement per Sqm over cleaned roof surfaces complete all as specified and as directed by Engineer-in-Charge.
640
-
-
Material and labour PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in padding on RCC roof finished fair and even including demolition of existing PCC complete all as specified and as directed by Engineer-in-Charge.
32
-
-
M&L for preparation and cleaning surfaces of concrete including flashing and junction of parapets etc and applying APP based polymeric membrane minimum weight 3 kg/sqm and minimum 3 mm thick reinforced with non woven fabric with torch application over and including a coat of oil base bituminous primer including taking down of old APP sheet complete all as specified and as directed by Engineer-in-Charge.
672
-
-
M&L for 40 mm thick Brick tiles laid over screed bed 15 mm thick cement mortar 1:6 and joints grouted flush in Cement Mortar 1:3, complete as specified and as directed by Engineer-in-Charge.
300
-
-
All as per Serial Item no. 16.00 heerein-before but except brick tiles
340
-
-
Demolition of lime concrete/ lean concrete/ Brick bats etc. from sunken slab portion exc. 15 cm thick but above ground floors, including removal of demolished material from MD land complete all as specified and as directed by Engineer-in-Charge.
38
-
-
M&L for 25 mm thick Plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregates) as in flooring laid in slope complete all as specified and directed by Engineer-in-Charge.
83
-
-
M&L for providing water proofing treatment of sunken portion of WCs, bathroom etc. by applying cement slurry mixed with Acrylic based polymer modified cementitious composite compound coating of make asapproval in Technical Instruction 5/ 2003 by adding:
(a) 15 mm thick plaster (1:4) cement sand mortar with integral water proofing compound 2% by weight of cement on floor and wall, finishing the surface even and smooth without using extra cement. The surface shall then be cured and allwed to dry.
(Note: Water proofing compound shall be measured and paid separately).
(b) First layer of slurry of cement @ 0.488 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hrs.
170
-
-
(c) Second layer of slurry of cement @ 0.242 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hrs followed with water curing for 48 hrs. complete all as specified and directed by Engineer-in-charge.
-
-
-
M&L lime concrete using 40 mm brick aggregates in lime mortar 1:3 as in sunken portion complete all as specified and directed by Engineer-in-charge.
35
-
-
Supply and fixing GI tube, 40 mm dia, 'medium grade' as in spouts/ short length including making holes in embedded sunken portion complete all as specified and directed by Engineer-in-charge.
12
-
-
Taking up or down GI steel/ Kitek tubing, 15 mm dia bore with connections or fittings from wall, ceiling, floor etc., including cleaning of tubes for re-fixing complete all as specified and directed by Engineer-in-Charge.
105
-
-
Taking up or down GI steel/ Kitek tubing, 20 mm dia bore with connections or fittings from wall, ceiling, floor etc., including cleaning of tubes for re-fixing complete all as specified and directed by Engineer-in-Charge.
80
-
-
S&F GI water tubes, 15 mm bore, 'medium grade', galvanized with all fittings and fixed complete to walls, ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.
300
-
-
S&F GI water tubes, 20 mm bore, 'medium grade', galvanized with all fittings and fixed complete to walls, ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.
230
-
-
Re-fixing of steel water tube, 15 mm bore, with provision of all new fittings fixed at new or old position, laid in floor along wall or at ceiling complete all as specified and directed by Engineer-in-Charge.
60
-
-
Re-fixing of steel water tube, 20 mm bore, with provision of all new fittings fixed at new or old position, laid in floor along wall or at ceiling complete all as specified and directed by Engineer-in-Charge.
40
-
-
Cutting chases, pinning in, of brick walls or concrete surfaces, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of inserting sheets, landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing, etc., and making good, cutting not exc 15 cm girth complete all as specified and directed by Engineer-in-Charge.
260
-
-
M&L for cutting holes into or through brick walls built in cement mortar or cement lime mortar having superficial area not exceeding 150 Sqcm each, making good in cement mortar 1:3 or cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregates) complete all as specified and directed by Engineer-in-Charge.
720
-
-
S&F rotational moulded polyethylene water storage tank (Cylindrical vertical with close top), HDPE, triple layered, ISI marked, 500 litres capacity with inlet & outlet connections, including tank nipple 150 mm long with washer & plug, with tank lid having locking arrangement hoisted and fixed in position complete all as specified and as directed including dismantling existing water storage tanks (RCC/ PVC) of capacity upto 500 litre complete all as specified as directed by Engineer-in-Charge.
7
-
-
S&F in repairs Gun-metal, globe or gate valves, with iron wheel head, 15 mm bore, screwed both ends for iron pipe, and fixed in repairs complete all as specified and directed by Engineer-in-Charge.
13
-
-
All as per Serial Item No. 32.00 here-in-before but for 20 mm bore
13
-
-
S&F Float/ Ball valves, high pressure, PTMT, ISI marked, with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 20 mm bore (minimum weight 210 gm) fixed in repair complete all as specified and as directed by Engineer-in-Charge.
13
-
-
Demolition of brick work built in cement mortar including all quoins, arches, pillar etc., complete including removing the waste materials to a distance of 500 meters complete all as specified and directed by Engineer-in-Charge.
8
-
-
Material & Labour for Brick work with sub class 'B' Bricks, straight or curved on plan exceeding 6 metre mean radius built in CM 1:6, complete all as specified and as directed Engineer-in-Charge.
8
-
-
Material and labour for brick work, with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall, built in cement mortar (1: 4) as in manholes and septic tanks complete all as specified and as directed by Engineer-in-Charge.
50
-
-
M&L for Plain cement concrete 1:2:4, Type B-1, (using 20 mm graded stone aggregates) as in roof kerbs and like rounded or chamfered on edges, copings complete all as specified and as directed by Engineer-in-Charge.
3.6
-
-
Taking down cement plaster of any description on brick or concrete walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed by Engineer-in-Charge.
600
-
-
M&L for Rendering 15 mm thick, in cement mortar 1:4 on brick or concrete surfaces with WPC (paid separately) complete all as specified and as directed by Engineer-in-Charge.
180
-
-
M&L for Rendering 15 mm thick in Cement Mortar 1:6, on brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.
370
-
-
M&L for Rendering 10 mm thick in cement mortar 1:3 on ceiling surfaces, finished even and smooth complete all as specified and as directed by Engineer-in-Charge.
50
-
-
Supply only Integral waterproofing compound, ISI Marked, complete all as specified and as directed by Engineer-in-Charge.
65
-
-
M&L for Preparation of newly plastered wall surfaces and applying wall care putty, not less than 2-3 mm thick over a coat of primer including smoothening the surfaces with sand papers etc, and applying two coats of Oil Bound Distemper complete all as specified and as directed by Engineer-in-Charge.
370
-
-
M&L for Preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and as directed by Engineer-in-Charge.
180
-
-
M&L for Preparation of newly plastered ceiling surfaces and applying two coats of Oil Bound Distemper complete all as specified and as directed by Engineer-in-Charge.
50
-
-
Complete removal of existing treatment from internal/ external surfaces of building of any type viz white wash, distemper, cement base paint, external emulsion, texture finished exteriror paint etc with mechanical means including necessary scaffolding and safety arrangements, up to height of four storey building by using sand papering to make surface smooth and ready to receive exterior painting complete all as specified and as directed by Engineer-in-Charge.
800
-
-
M&L for preparation of old decorated wall surfaces and applying two coats of oil bound distemper complete all as specified and as directed by Engineer-in-Charge.
3000
-
-
M&L for preparation of old decorated wall surfaces and applying one coat of oil bound distemper complete all as specified and as directed by Engineer-in-Charge.
550
-
-
M&L for preparation of old decorated Ceiling surfaces and applying one coat of oil bound distemper complete all as specified and as directed by Engineer-in-Charge.
1100
-
-
M&L for preparation of old surfaces of walls and applying two coats of cement base paint, up to height of four storey building including necessary scafolding and safety arrangements complete all as specified and as directed by Engineer-in-Charge.
1300
-
-
M&L for preparation of old surfaces of walls and applying one coat of cement base paint, up to height of four storey building including necessary scaffolding and safety arrangements complete all as specified and as directed by Engineer-in-Charge.
300
-
-
M&L for preparation of old existing or new plastered/ unplastered surface and applying two coats of exterior emulsion paint on surface of building (all as per manufactures instructions) up to height of four storey building with and including necessary scaffolding and safety arrangements complete all as specified and as directed by Engineer-in-Charge.
100
-
-
S&F PVC (SWR) pipes, 110 mm bore, single socketed in any length with rubber ring joints as in repair fixed to walls or laid in trenches complete all as specified and as directed by Engineer-in-Charge.
85
-
-
S&F PVC (SWR) bend, Tees, cowl 110 mm bore fixed as in repair complete all as specified and as directed by Engineer-in-Charge.
20
-
-
S&F PVC (SWR) pipes, 75 mm bore, single socketed in any length with rubber ring joints as in repair fixed to walls or laid in trenches complete all as specified and as directed by Engineer-in-Charge.
80
-
-
S&F PVC (SWR) bend, Tees, cowl 75 mm bore fixed as in repair complete all as specified and directed.
20
-
-
Supply and fixing 100 mm bore, cast iron soil waste and vent pipes, in any length with or without ears with cement joints fixed as in repair to wall or laid in trenches complete all as specified and as directed by Engineer-in-Charge.
90
-
-
All as per Serial Item No. 58.00 here-in-before but 75 mm bore
90
-
-
Supply and fixing Cast iron bends (any radius), diminishing pieces or tapers (largrer bore measured) or Tees suitable for 75 mm bore pipes, ISI marked, fixed as in repair complete all as specified and as directed by Engineer-in-Charge.
40
-
-
All as per item No. 60.00 here-in-before but for 100 mm bore pipe
40
-
-
S&F Cast iron Floor trap including jointing to waste pipe with cement joint, dia of outlet 75 mm fixed in repairs complete all as specified and directed by Engineer-in-charge.
35
-
-
Supply and fixing in repair PVC (SWR) floor trap, 75 mm bore, plain with grating incl jointing with solvent cement, fixed as in repair complete all as specified and directed by Engineer-in-charge.
35
-
-
Taking down shutters of any description not exceeding 1 Sqm each and removing from site complete all as specified and directed by Engineer-in-charge.
65
-
-
Taking down shutter of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each and removing from site complete all as specified and directed by Engineer-in-charge.
38
-
-
Taking down chowkhats or frames not exceeding 1.5 Sqm with shutter (without taking off shutters from the frame) and removal from site complete all as specified and directed by Engineer-in-charge.
42
-
-
Taking down chowkhats or frame exceeding 1.5 Sqm but not exceeding 4.00 Sqm with shutters (without taking off shutters from the frame) and removal from site complete all as specified and directed by Engineer-in-charge.
16
-
-
Supply and Fixing Steel windows, factory made with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including a shop coat of red oxide primer and finished smooth and fair complete all as specified and directed by Engineer-in-charge.
16
-
-
Supply and fixing steel ventilator, factory made, fixed type including hinges, steel peg stay, including a shop coat of red oxide primer and finished smooth and fair surface complete all as specified and directed by Engineer-in-charge.
5
-
-
Supply & Fixing factory made Solid PVC Door Frame having profile 75 mm x 50 mm with one rebate, homogeneous fine cellular structure having density of 550 smooth outer integral skin with suitable metal stiffners & fixed with 100 x 8 mm sheet metal screws all as per specification & drawing of manufacturer complete all as specified and directed by Engineer-in-charge.
174
-
-
Suuply & Fixing Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed by Engineer-in-charge.
43
-
-
M&L for 2nd class hard wood, plain, solid, straight chowkhats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed by Engineer-in-charge.
0.9
-
-
S&F pressed steel frame for doors with double rebates of size 125 x 60 mm made with steel sheet of 1.25mm thickness in and including necessary fixing lugs, hinges, lock strike plate complete all as specified and directed by Engineer-in-charge.
65
-
-
M&L for providing cement concrete type C1 (1:3:6) 20 mm graded aggregate as in pressed steel door frame (backfill) complete all as specified and directed by Engineer-in-charge.
0.4
-
-
Cutting holes through brick wall built in cement mortar, for inserting holdfasts, depth of embedded portion of holdfasts exceeding half brick thick but not exceeding one brick thick and making good the dismantled portion with cement mortar (1:3) or PCC type B-1, (1:2:4) to match the disturbed surface with existing finish, complete all as specified and directed by Engineer-in-charge.
305
-
-
M&L for factory made 2nd class hardwood (Hollock) glazed & skeleton shutters (Single Shutter), 35mm thick open rebated and prepared to receive wire cloth, glass, gauze etc., edges of framing plain chamfered or rounded, fitted with cut and metred beads for securing glass, gauze etc sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(a), complete all as specified and directed by Engineer-in-charge.
70
-
-
NOTE : Wire gauge shutter should also have the provision of vertical member of size 75mm X 35mm at middle of the shutter. The vertical member have mitred joints and shall be stuck tenoned to the depth not less than 35 mm in top, lock & bottom rails and have rebate to receive the wire gauge etc. complete all as specified and directed by Engineer-in-charge.
-
-
-
S&F 2nd class hard wood factory made 35 mm thick panelled door shutter (two panel) factory made, with lock rail and panel of 9 mm thick BWP commercial ply or 12 veneered particle board with commercial veneering on both faces, the size of rail and style as per IS 1003 (part-I) klin seasoned and chamically treated complete all as specified and directed by Engineer-in-charge.
60
-
-
S&F 100 mm butt hinges, medium weight, cold rolled mild steel complete all as specified and directed by Engineer-in-charge.
130
-
-
S&F Extruded aluminium alloy handles, 150 mm, fabricated type, anodised complete all as specified and directed by Engineer-in-charge.
350
-
-
S&F aluminium anodized, barrel tower bolt of extruded section 150 mm long complete all as specified and directed by Engineer-in-charge.
70
-
-
S&F aluminium anodized, barrel tower bolt of extruded section 200 mm long complete all as specified and directed by Engineer-in-charge.
280
-
-
S&F in repairs aluminium alloy anodised sliding door bolt, 300 mm with hasp and staple (bolt type and fixing clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16 mm dia and 300 mm long complete all as specified and directed by Engineer-in-charge.
40
-
-
Supply and fixing in repairs 300 mm mild steel ordinary rat tail rod pattern spring including roller and roller plate, fixed complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring 140 mm long, fixed in floor complete all as specified and directed by Engineer-in-charge.
80
-
-
S&F Aluminium powder coated door seal strip with glass wool, having length 0.85 to 1.10 mtr, fixed with steel screws at bottom rail of external door complete all as specified and directed by Engineer-in-charge.
80
-
-
M&L for preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm in width or girth and applying 2 coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge.
100
-
-
M&L for Preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-charge.
230
-
-
M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-charge.
220
-
-
M&L for Preparation of old wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-charge.
240
-
-
Hacking out old broken glass (any thickness), size, quality etc from any type of frame fixed with pin, beading or oil putty complete all as specified and directed by Engineer-in-charge.
10
-
-
Supply and fixing 4 mm thick sheet glass, ordinary quality, in square not exceeding 0.5 Sqm in each panes and fixed in any type of frame and glazing with oil putty (or beading) complete all as specified and directed by Engineer-in-charge.
20
-
-
Supply and fixing 4 mm thick figured glass, pin head type, ordinary quality in squares not exceeding 0.50 Sqm in each panes and fixed in any type of frame and glazing with oil putty (or beading) complete all as specified and directed by Engineer-in-charge.
6
-
-
Supply and fixing galvanized MS wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm, fixed complete all as specified and directed by Engineer-in-charge.
38
-
-
Supply and fixing in repairs galvanized MS wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm, complete all as specified and directed by Engineer-in-charge.
10
-
-
S&F in repair Harrison rails (Curtain Rails), mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed by Engineer-in-charge.
160
-
-
Material and labour for Block Board 18/19 mm thick, 2nd quality, interior grade, commercial type, fixed with screws to timber frame work as in cup board, kitchen cabinet, cupboard racks, wardrobe fitted to chowkhats, with 6 mm thick IInd class hard wood edging on exposed edges, fixed complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F in repairs 18/ 19 mm thick pre-laminated particle board, exterior grade, prelaminated both sides with decorativce choice laminations, fixed with screws to timber frame as in cupboards, shutters, shelves, cabinets, pelmets etc including fixing 18 mm wide 6 mm thick painted beading all around of 1st class HW (Teak) complete all as specified and directed by Engineer-in-charge.
59
-
-
S&F in repairs continuous (Piano) hinges, mild steel, bright finish or electrogalvanised, 30 mm width of flaps when opened complete all as specified and directed by Engineer-in-charge.
140
-
-
S&F 150 mm size hasp and staple safety type aluminium anodized, in repairs complete all as specified and directed by Engineer-in-charge.
45
-
-
S&F magnetic catcher for kitchen cabinet and cupbords complete all as specified and directed by Engineer-in-charge.
160
-
-
M&L for welding in repairs exceeding 2.5 cm but not exceeding 5 cm in length, thickness of metal to be welded exceeding 6 mm but not exceeding 9 mm complete all as specified and directed by Engineer-in-charge.
30
-
-
Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed by Engineer-in-charge.
75
-
-
M&L for Framed work such as Hand rails, half round or other steel section drilled and counter sunk for balusters running bars, nosing to steps, railings, grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, ladders, Cooler stand ; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 and incl PCC type C-1 ratio 1:3:6 for embedding of sections, complete all as specified and directed by Engineer-in-charge.
300
-
-
Dismantling marble chips, floor/ wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-charge.
1953
-
-
M&L for Screed bed or bedding layer 15 mm thick in CM 1:6, for laying under floor finishes complete all as specified and directed by Engineer-in-charge.
1448
-
-
M&L for 10 mm thick rendering/ backing coat in CM 1:6 finished even and rough to receive wall tiles, complete all as specified and directed by Engineer-in-charge.
661
-
-
Material and labour for non skid, joint free first quality ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, complete all as specified and directed by Engineer-in-charge.
350
-
-
Material and labour for glazed ceramic tiles in vertical surface 350 x 450 x 7 mm thick or 300 x 450 x 7 mm, joint free, first quality, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, complete all as specified and directed by Engineer-in-charge.
545
-
-
Material and labour for Vitrified Ceramic tiles 10 mm thick First quality (square/ rectagular) polished, area of each tiles not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed by Engineer-in-charge.
733
-
-
All as per Serial Item no. 109.00 but on vertical surfaces (skirting/ dados)
80
-
-
Material and labour for machine cut pre-polished kota stone slab, 18-20 mm thick (single slab) laid in step/ floors with neat cement slurry @ 3.00 kg/square metre, including pointing in grey cement slurry to match the shade of slab and cutting groves in stone and making nosing at edges, etc., complete all as specified and directed by Engineer-in-charge.
120
-
-
Material and labour for machine cut pre-polished kota stone slab, 20-25 mm thick (single slab) in riser of steps, skirting, dado and pillar, laid with neat cement slurry @ 3.00 kg/square metre including pointing in grey cement slurry to match the shade of slab, complete all as specified and directed by Engineer-in-charge.
4
-
-
Material and labour for machine cut pre-polished Green Marble work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed by Engineer-in-charge.
245
-
-
Material and labour for machine cut pre-polished Green Marble work 18 to 20 mm thick (table rubbed and polished) in risers to steps, skirting, dados etc. and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed by Engineer-in-charge.
32
-
-
S&F Bevelled edge mirror, 5 to 6 mm thick, selected quality glass, 600 x 450 mm size, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, fixed in repairs complete all as specified and directed by Engineer-in-charge.
40
-
-
Supply and fixing toilet paper holder, cast copper alloy, chromium plated fixed in position, fixed, complete all as specified and directed by Engineer-in-charge.
40
-
-
Supply and fixing in repair vitreous china wash hand basin, white, flat back, size 550 x 400 mm including brackets of suitable size, complete all as specified and directed by Engineer-in-Charge.
40
-
-
S&F Waste coupling, Brass Chromium plated (half or full threaded) 32 mm bore complete all as specified and directed by Engineer-in-Charge.
40
-
-
Supply and fixing PVC waste pipe 32 mm dia fixed, complete all as specified and directed by Engineer-in-Charge.
40
-
-
S&F of grating doom 125 mm dia with waste hole of PTMT (minimum weight 40 gm). complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F stainless steel soap dish in repair size 160 x 160 x 90mm, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. in repair complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F virgin polypropylene flushing cistern, ISI marked, white at low level of 10 litre capacity, complete with PVC bend/ flush pipe and making all connection including taking down existing high level/ low level cistern with all connections and making good the disturbed surfaces in cement mortar (1:3) to match with the existing surface, complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F Plastic water closet seat cover, white, closed pattern with flat bottom and mild steel chromium plated hinging device, ISI marked complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F Flush pipe (any length) of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F Flushing jet for pedestal pattern WC including flexible pipe and brass Chromium plated nuts, complete all as specified and directed by Engineer-in-charge.
40
-
-
Supply and fixing in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F in repair 15 mm bore bib taps, long body, cast copper alloy, chromium plated with capstan head, screwed down for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge.
120
-
-
S&F in repair 15 mm bore Bib taps, short body, cast copper alloy, chromium plated with capstan head, screwed down for iron pipe or for brass ferrule, complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F in repair 15 mm bore Stop valves (concealed type), cast copper alloy, chromium plated, screwed down, high pressure, with capstan head, with long shank and cup screwed both ends for iron pipe or for unions, complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F in repair 15 mm bore Angle valve, cast copper alloy, chromium plated, screwed down, high pressure, with capstan head, complete all as specified and directed by Engineer-in-charge.
160
-
-
S&F in repair Chromium plated brass shower rose with arm 100/ 125 mm dia with swivel joints, including fixing to pipe or union complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F Pillar taps, cast copper alloy, fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore, fixed in repairs complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F PVC connection 15 mm dia and 45 cm long with 2 Nos PTMT nuts, fixed in repairs complete all as specified and directed by Engineer-in-charge.
80
-
-
Supply and fixing PVC bathroom mirror cabinet, 500 x 400 mm, fixed with and including chromium plated brass screws and PVC rawl plugs, fixed complete all as specified and directed by Engineer-in-charge.
40
-
-
S&F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf, 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed by Engineer-in-Charge.
40
-
-
S&F Aluminium anodized Peg set of six and fixing it with screws complete all as specified and directed by Engineer-in-Charge.
120
-
-
S&F Tubular towel rail, brass chromium plated, 20 mm dia, D type, 60 cm long between flanges, fixed in repairs complete all as specified and directed by Engineer-in-Charge.
40
-
-
Supply and fixing precast cement concrete louvres and jallies, factory made, 25 mm thick (measured solid), made out of cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregates), set in CM 1:6, including all mouldings complete all as specified and directed by Engineer-in-Charge.
20
-
-
Taking down copper/ aluminum point wiring (light, fan, socket point 5/15 amps) complete including fitting such as switches, ceiling rose, light fittings, sockets, bulb holder, ceiling roses etc and removing retrieved materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors etc complete all as specified and as directed by Engineer-in-Charge.
805
-
-
M&L for Point wiring with PVC insulated PVC unsheathed electric FRLSH cable, 1100V grade, single core having multi stranded copper conductor of size 1.5 sqmm for phase & neutral in and including concealed PVC conduits, ISI marked, medium grade, not less than 20 mm dia with all conduit accessories, sheet steel modular sunken/ flush box 1.2 mm thick and suitable size of frame cover for mounting modular switch, socket and regulator fixed on surface in touch with wall and including 1.5 sqmm PVC insulated unsheathed copper conductor cable as earth wire connected to earth dolly by providing lugs for one light point/ fan point/ bell point controlled by one switch complete all as specified and as directed by Engineer-in-Charge.
456
-
-
All as per Serial Item No 141.00 here-in-before but for one socket outlet 3/5 pin, 5 amps on same board.
105
-
-
All as per Serial Item No 141.00 here-in-before but for one socket outlet 3/5 pin, 5 amps on independent board.
156
-
-
All as per Serial Item No 141.00 here-in-before but for one socket outlet 3/5 pin, 15 amps on independent board size of cable 2.5 sqmm for phase, neutral & 2.5 sqmm as earth wire.
88
-
-
S&F modular switch, 6 Amps, one way, one module 230 volts single pole complete all as specified and as directed by Engineer-in-Charge.
675
-
-
S&F modular switch, 16 Amps, one way, one module 230 volts single pole complete all as specified and as directed by Engineer-in-Charge.
88
-
-
S&F modular socket outlet, 3/5 pin, 6 Amps two module 230 volts complete all as specified and as directed by Engineer-in-Charge.
261
-
-
S&F modular socket outlet, 6/16 Amps, 2 in 1, universal type, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.
88
-
-
S&F modular bell push, single pole, one module, 230 volts complete all as specified and as directed by Engineer-in-Charge.
42
-
-
S&F ceiling rose, surface bakelite 65 x 50 mm dia three terminal complete all as specified and as directed by Engineer-in-Charge.
210
-
-
S&F electric bell in repair AC 230 volt, single pole complete all as specified and as directed by Engineer-in-Charge.
42
-
-
S&F fan regulator, modular type, single pole, 230 volt two module, complete all as specified and as directed by Engineer-in-Charge.
84
-
-
S&F Lamp holder, insulated body PVC/ Polycarbonate type with backplate suitable for batten fitting complete all as specified and as directed by Engineer-in-Charge.
84
-
-
S&F LED Lamp 9 W, B22 type (Inverter bulb) complete all as specified and as directed by Engineer-in-Charge.
84
-
-
M&L for disconnection of power supply and taking down carefully by unscrewing from boards fitting and fixture such as MCB DB, junction box, panels of any size complete with all MCCBs, MCBs etc and removing from site, complete all as specified and as directed by Engineer-in-Charge.
26
-
-
S&F vertical TPN distribution board, double door, flush mounting with provisions for MCCBs incomer upto 125 to 160 Amp & outgoing, 4 way, having IP 54 protection complete all as specified and as directed by Engineer-in-Charge.
6
-
-
S&F MCCB 125 Amps, 4 pole, 3 phase, 415 volts, 16 KA with Ics = 100% Icu with adjustable thermal and magnetic release complete with proper copper thimble complete all as specified and as directed by Engineer-in-Charge.
6
-
-
S&F sheet metal enclosure MCB DB, SPN 240 volts, 8 way, double door fitted with bus bar, neutral link, earth bar and din rail complete all as specified and as directed by Engineer-in-Charge.
20
-
-
S&F MCB, SPN, 40 to 63 Amps, 230 volts in repair having breaking capacity 10KA "C" type complete all as specified and as directed by Engineer-in-Charge.
20
-
-
S&F MCB, SP, 40 Amps, 230 volts in repair having breaking capacity 10KA "B" type complete all as specified and as directed by Engineer-in-Charge.
55
-
-
S&F MCB, SP, 6 to 32 Amps, 230 volts in repair having breaking capacity 10KA, "C" type complete all as specified and as directed by Engineer-in-Charge.
112
-
-
S&F LED light fitting in repair 9W/ 10W bulkhead luminaries, including LED light driver connection up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by Engineer-in-Charge.
35
-
-
S&F in repair slim LED batten with polycarbonate housing and diffuser with elegantly desinged end caps 1 x 20W, 220 V, AC connecting up with three core flexible of suitable size from ceiling rose complete all as specified and as directed by Engineer-in-Charge.
72
-
-
Supply & fixing in repairs LED batten, mirror light 10W, of two feet length, complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and as directed by Engineer-in-charge.
42
-
-
Taking down and refixing after repair of LED batten fitting 1 x 10W/ 20W, 220 V, AC after cleaning and connecting up with three core flexible of suitable size (if required) from ceiling rose complete all as specified and as directed by Engineer-in-charge.
65
-
-
Disconnection and Taking down carefully copper/ aluminium sub main wiring including PVC conduit pipe of any size and any type complete all as specified and as directed by Engineer-in-charge.
440
-
-
M&L of Sub main wiring with two runs of single core PVC insulated and unsheathed multistranded, copper conductor (FRLSH) cable of size 6.0 sqmm LT, 1100V grade, down through and including PVC non metallic conduit of approprite dia with accessories and fittings and one run of 6.0 sqmm single core multi stranded copper conductor cable as earth continuity conductor complete all as specified and as directed by Engineer-in-charge.
440
-
-
M&L of Sub main wiring with two runs of single core PVC insulated and unsheathed multistranded, copper conductor (FRLSH) cable of size 10.0 sqmm LT, 1100V grade, down through and including PVC non metallic conduit of approprite dia with accessories and fittings and one run of 10.0 sqmm single core multi stranded copper conductor cable as earth continuity conductor complete all as specified and as directed by Engineer-in-charge.
85
-
-
Note for Srl Item no. 164.00 and 165.00:-
1. Two runs of cable, one run of earth wire and one run of PVC non metallic conduit shall be measured as one run length.
2. Cable required for connection to DBs shall deemed to be including and shall not be measured separately. 3. Earth wire shall run inside the conduit pipe complete all as specified.
-
-
-
S&F in repair LED security light fitting, 35 watt, 230 volts, outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp including bracket up to 1.5 metre length, with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and as directed by Engineer-in-charge.
6
-
-
Supply & fixing of 20/ 25 mm dia, rigid non metallic PVC conduit, 'ISI marked', inclusive of all fittings (such as junction boxes, bends, elbows, tees, reducers, bell mouth tube ends) and all fixing accessories such as couplers lock nuts, saddless, pipe hooks etc for wiring, complete all as specified and as directed by Engineer-in-Charge.
410
-
-
Cutting chases, pinning in, making good to facing where required and pointing in CM (1:3) to ends or edges of landings, steps, cills, sunsheds, shelves, lintel etc for concealed conduit wiring etc not exceeding 10 cm width or girth complete all as specified and as directed by Engineer-in-charge.
410
-
-
Supply and fixing of exhaust fan, made of sturdy Engineering plastic body complete with louvers/ shutter, voltage 230V, 50 Hz, 1200 RPM, Copper winding of sweep 300 mm complete all as specified and as directed by Engineer-in-charge.
42
-
-
Excavation in trenches not exceeding 1.5 meter wide and not exceeding 1.5 meter in deep getting out in any type of soil for stay assembly/ laying of cable/ erection of poles etc complete all as specified and as directed by Engineer-in-charge.
18.3
-
-
Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick complete all as specified and as directed by Engineer-in-charge.
8.5
-
-
Removing of excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by Engineer-in-charge.
9.8
-
-
M&L for Sand cushioning to UG cable 8cm thick before laying the cable and 15cm above the cable as specified in SSR to under ground cable including punning down of sand in layer complete all as specified and as directed by Engineer-in-charge. Note:(i) Consolidated/ Punned sand thickness shall be considered for purpose of payment.
(ii) Sand shall be same as specified for plastering work.
7.3
-
-
Supply and Laying of bricks well burnt sub class B (old size) laid flat for cable protection width equal to the length of bricks complete all as specified and directed by Engineer-in-Charge.
1.55
-
-
Supply, laying & testing of XLPE insulated, armoured, heavy duty LT cable, with stranded aluminium conductor, 1100 volts grade, of size 35 sqmm, 3.5 core, laid in trenches, sleeving through pipes or fixed on poles & walls or laid under floors including jointing with suitable size aluminium lugs including taking down existing unserviceable cable complete all as specified and directed by Engineer-in-Charge.
105
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%