Military Engineer Services Tender
If you want to inquire about any e-tender the Haryana government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Haryana tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Haryana etender you're looking for. Read further to learn how to search and bid for etender Haryana.
Costs
EMD
₹ 50,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_663386_1Bid Award Id
ViewTender No
GE/SRA/T-45/2024-25Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
M&L for laying pre-polished 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; incl taking out existing old paver blocks and removing from site complete all as specified and directed.
(NOTE: Sand cushioning shall be measured and paid separately)
300
-
-
... More
M&L sand filling under floors or in foundation incl watering and consolidation complete all as specified and directed.
7.5
-
-
... More
M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.
3
-
-
... More
M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) as in Coping, Bed Plates, Holdfast, Bed Block, Kerb Stones including necessary Formwork and weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.
1
-
-
... More
Demolition Brick work built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc. and removal of debris from site complete all as specified and directed.
3.42
-
-
... More
M&L for Brick Work with Fly-Ash Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.
6.21
-
-
... More
Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and directed.
180
-
-
... More
M&L for Rendering (Internal) 15mm thick in cement mortar 1:6 on Brick Walls or on Concrete Surfaces, Plastered Surfaces finished Even and Smooth without using Extra Cement complete all as specified and directed.
180
-
-
... More
M&L preparing new Plastered surfaces of Walls by applying 1.5mm Wall Putty including Rubbing down with Sand Paper to obtain a Smooth Finish Surface and applying Two Coats of Plastic Emulsion Paint (of approved tint) over a Coat of suitable Primer with rollers, complete all as specified and directed.
180
-
-
... More
M&L for 15 mm thick plastering in two layers, 10 mm + 5 mm in cement mortar 1:4, top layer of 5 mm thickness mixed with with water proofing compound (as per manufacturer's instructions) on brick/stone walls or concrete surfaces finished even and fair (upto any height) for external surfaces complete all as specified and directed.
Note : Water Proofing compound shall be measured and paid seperately as "Supply only".
18
-
-
... More
Supply only Liquid Water Proofing Compound, conforming to IS and/or as approved, complete all as specified.
0.67
-
-
... More
M&L for preparation of newly plastered surfaces and applying exterior wall putty 1.5 mm thick for smooth surface and finished with two coats of exterior acrylic emulsion paint (having anti-dust & anti-algae properties) duly mixed with stainer to achieve approved Tint/shade (in camouflage pattern) over a coat of suitable exterior primer, applied with rollers to new wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufactuirer's instructions, upto 4 storey height complete all as specified and directed.
18
-
-
... More
Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, snap grid etc complete all as specified and as directed.
982
-
-
... More
S&F 6mm thick HPSC cement fibre plain building boards, fixed to wall, including finishing with 1.5 mm thick wall putty complete all as specified and directed.
20
-
-
... More
S&F 12mm thick mineral fibre core ceiling board/tiles for insulation and accoustic purposes, 60x60 cm in size, fixed with GI Snap Grid Frame Work with Steel Screws, complete all as specified and directed.
462
-
-
... More
-ditto- but using serviceable ceilling board obtained from dismantling complete all as specified and directed by Engr-in-Charge.
500
-
-
... More
S&F false ceiling with powder coated exposed G.I. grid suspension system consisting of Main Runner 3600 mm long, Cross Tee 1200mm/600mm long and Wall Angle, wall angle fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300 mm c/c, Main Runners placed @ 1200mm, Cross Tee 1200mm inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm x 600mm and additional cross tees of 600 mm placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600mm x 600mm, grid of module size 600mm x 600mm shall be supported by 6 mm dia G.I. wire from purlins/soffit complete all as specified and directed. Note: Ceiling board will measured and paid seperately under appropriate item.
462
-
-
... More
-ditto- but using serviceable ceiling grid sections obtained from dismantling against Item No 16 here-in-before.
Note: Ceiling board will measured and paid seperately under appropriate item.
500
-
-
... More
Dismantling Floor, Paver Tiles, Hearth or Wall Tiling, etc. including Cement Mortar Bedding (but not backing) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed.
1116.8
-
-
... More
M&L Vitrified Coloured Tiles 9 to 10mm thick (Square/ Rectangular), Double Charge, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Tiles, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed.
NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.
50
-
-
... More
M&L Vitrified Coloured Tiles 9 to 10mm thick (Square/ Rectangular), Double Charge, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc. Set and Jointed in Neat Cement Slurry, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, including goruting of joints complete all as specified and directed.
NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate. Grouting shall be measured and paid seperately.
1000
-
-
... More
M&L for grouting joints of ceramic floor tiles, having 3mm joint width using epoxy grout mix of 0.70 Kg of organic coated filler of desired shade (0.10 Kg of hardener and 0.20 Kg of resin per Kg) including filling/grouting and finishing complete all as specified and directed.
1000
-
-
... More
M&L Vitrified Coloured Tiles 9 to 10mm thick (Square/ Rectangular) Double Charge, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Vertical Surface i.e. Dado, Skirting,etc., set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the Tiles, laid over and including 10mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed.
NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.
16.8
-
-
... More
M&L for providing outdoor ceramic Floor (Paver) Tiles, 400 x 400 x 9.0 to 10mm thick, highly abrasive, Anti-skid, Impact Resistant, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete including providing 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.
(NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.
50
-
-
... More
M&L for providing Coloured/Printed Glazed Ceramic Tiles, 450x300x6-7mm thick in Vertical Surfaces i.e. Dado, Skirting, etc., set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the Tiles, fixed over and including Screed or Screed Bed 10mm thick in Cement Mortar 1:3, complete all as specified and directed.
NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.
200
-
-
... More
Dismantling stone slabs and tiles, laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc incuding removal of debris from site complete all as specified and directed.
8
-
-
... More
M&L for Granite (of any type) work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including edge moulding, grinding and polishing, laid over and including 20mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed.
NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.
5
-
-
... More
M&L for providing Machine cut Kota Stone Slab 20-25mm thick in Flooring, laid over 20mm thick Screed base in Cement Mortar 1:4 laid and joined with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and as directed.
NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.
75
-
-
... More
Taking down existing bird proof net of any size complete all as specified and directed.
1000
-
-
... More
S&F bird proof netting UV stabilized made of 1mm dia HDPE/Nylon wire having mesh size n.exc 25mmx25mm, tightening/securing the joints by using stainless steel wire of suitable thickness complete all as specified and directed.
1000
-
-
... More
M&L for cleaning of existing bird proof net including necessary arrangement at a height 15mtr (Approx) complete all as specified and as direced by Engr-in-charge at site.
Note: Cleaning of bird proof net shall be done at least once in a quarter.
30000
-
-
... More
M&L for tightening / securing the joints of existing bird proofing with stainless steel wire of suitable thickness to prevent the enrty of birds complete all directed at site by Engr-in-Charge.
Note : Joints of net to be measured for payment.
2500
-
-
... More
NOTES FOR ITEM NO 32-35 :-
1) The work is required to be executed at a height of approx 15 metres. Contractor's quoted rate shall be deemed to included for cost of all machinery and safety gear required for execution of the work. No claim shall be admissible at a later stage.
-
-
-
... More
Demolition of Cement Concrete (Reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.
1.63
-
-
... More
M&L Reinforced Cement Concrete 1:2:4 type B1 (20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.
(NOTE: MS reinforcement & Formwork shall be measured and paid seperately)
9.36
-
-
... More
M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces complete all as specified and directed.
35
-
-
... More
M&L TMT Bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hoping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia or securing with Clips, complete all as specified and directed.
500
-
-
... More
M&L TMT Bars 06-08mm dia, cut to length bent to shape required including cranking, bending spirally for hoping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia or securing with Clips, complete all as specified and directed.
110
-
-
... More
Dismantling of plain or corrugated steel sheeting any gauge, thickness, including nainital or similar pattern roof covering & removing off the site complete all as specified and directed.
300
-
-
... More
Dismantling of fibreglass/polycarbonate roofing sheet (corrugated, semicorrugated, plain, etc.) sheets in roof/wall coverings and removal from site complete all as specified and directed.
90
-
-
... More
Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, in any position and removal from site complete all as specified and directed
210
-
-
... More
Dismantling structural steel work of any discription not otherwise provided for and removal from site complete all as specified and directed.
6.25
-
-
... More
Taking down roof trusses, coupled rafters or trussed beams, of clear span above 4 metres and upto 8 metres and removal from site complete all as specified and directed.
7
-
-
... More
M&L for steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed.
(NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)
2500
-
-
... More
M&L for Mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 30 cm long, dia exc 12 mm but not exc 20 mm complete all as specified and directed.
50
-
-
... More
M&L for preparing New or previously untreated Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and directed.
30
-
-
... More
S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.
300
-
-
... More
S&F 1.5mm thick Polycarbonate transparent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.
90
-
-
... More
S&F 5 mm thick plain acrylic sheet (any colour), fixed with coach screws and washers in steel frame work complete all as specified and directed.
22
-
-
... More
S&F in repairs circulator/ventilator wind driven turbine, 600 mm size with FRP base of size 32" x 24" to match roof sheet with polyster resin powder coated, top of ventilator turbine made out from aluminium with integrated and reinforced main bearing housing the shaft of stainless steel and varpitch from alumnium, rotation bearing will be twin ZZ ball bearing encased in single integrated bearing housing etc complete all as specified and directed. (MAKE : SVS, Model : Windy 24 Plus or equivalent model in Shrijee / Golden Engineers / Airier)
NOTES :- The work is required to be executed at a height of approx 20 metres. Contractor's quoted rate shall be deemed to included for cost of all machinery and safety gear required for execution of the work. No claim shall be admissible at a later stage.
8
-
-
... More
S&F in repair Rotational Moulded Polyethene Water Storage Tank, 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS, hoisted and fixed in Position complete all as specified and directed.
1
-
-
... More
S&F in repair Rotational Moulded Polyethene Water Storage Tank, 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS, hoisted and fixed in Position complete all as specified and directed.
1
-
-
... More
S&F in repair 20 mm bore Ball brass valves, high pressure, with HDPE float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.
(MAKE : PRAYAG, Cat No. B-152 or equivalent model in makes specified in tender)
2
-
-
... More
S&F in repair Looking Mirror 5.0mm thick of size 600x600mm, fixed with Chromium Plated Brass Spacers 25mm to 30mm in size (One Each Corner) including rounding the edges of the Mirror complete all as specified and directed.
2
-
-
... More
S&F in repair Brass Chromium Plated Tubular Towel Rail 20mm dia, 60 Cm long with Bracket complete all as specified and directed.
2
-
-
... More
S&F in repair Chromium Plated health faucet with 1mtr stainless steel tube indcluding necessary fitting and fixtures complete all as specified and directed.
5
-
-
... More
S&F in repair Vitreous china, white, half stall urinal flat back with grating and union for discharge pipe (excl flush pipe and flushing cistern and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe complete all as specified and directed.
(NOTE: Cost of CP waste coupling shall be deemed to be included in the quoted rate)
1
-
-
... More
S&F in repair Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), White, Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device and complete all as specified and directed.
NOTE: This item shall be measured for replacement of only seat cover on existing EWC.
1
-
-
... More
S&F in repair 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.
3
-
-
... More
S&F in repair 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.
3
-
-
... More
S&F in repair PVC (SWR) bends any 75mm bore complete all as specified and directed
2
-
-
... More
S&F in repair PVC (SWR) bends any 110mm bore complete all as specified and directed
2
-
-
... More
S&F in repair 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement
2
-
-
... More
Taking up or down Steel Tubing 15mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and directed.
5
-
-
... More
Taking up or down Steel Tubing 20mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and directed.
80
-
-
... More
Supply & laying Steel Water Tubing 15mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation, complete as all specified and directed.
4
-
-
... More
Refixing Old Steel Tubing 15mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No 67 here-in-before) in new or old position (Walls, Ceiling, Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of new GI Connections (as required ordered at Sites), complete all as specified and directed.
1
-
-
... More
Supply & laying Steel Water Tubing 20mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation, complete as all specified and directed.
70
-
-
... More
Refixing Old Steel Tubing 20mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 68 here-in-before) in new or old position (Walls, Ceiling, Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of new GI Connections (as required ordered at Sites), complete all as specified and directed.
10
-
-
... More
S&F in repair PVC Flushing Cistern 10 Litre capacity White, Low Level, Valve less, Syphonic action type with Inlet, Ball Valve, Float and Handle, PVC Waste Pipe 32mm bore (dia) of suitable Length, a pair of Cast Iron Bracket/ Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 complete all as specified and directed.
5
-
-
... More
S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm excluding taps,waste, chain and plug and porcelain stopper but including brackets cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete as all specified and directed. (NOTE: Cost of CP wate coupling and PVC waste pipe is deemed to be included in the quoted rates)
2
-
-
... More
S&F in repair Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, Long Body with Capstan Head, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and directed.
5
-
-
... More
S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, facny type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete as all specified and directed.
5
-
-
... More
S&F in repair Angle Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, screwed both Ends for Iron Pipe complete all as specified and directed.
5
-
-
... More
S&F in repairs for waste coupling chromium plated for sink /wash basin, suitable for 32mm dia waste pipe complete all as specified and directed.
(NOTE: This item shall only be measured for replacement in existing sinks, basins etc)
5
-
-
... More
S&F in repair PVC Waste Pipe 32mm bore (dia), 60-75 cm length (as required at Site), complete all as specified and directed.
(NOTE: This item shall only be measured for replacement in existing sinks, basins etc)
5
-
-
... More
S&F in repair PVC Connection Pipe 15mm size and 60 Cm in length with Adopter Nuts of PVC complete all as specified and directed.
10
-
-
... More
S&F in repair Jet Spray with Connection Pipe 15mm bore (dia), Brass Chromium Plated and suitable for Wash Down Water Closet Pan (Pedestal Pattern) , complete all as specified and as directed.
1
-
-
... More
Repair/Servicing of Urinal Sensor, any make or type including replacement of necessary washers, battery etc to ensure proper flow of water complete all as specified and directed.
NOTE: In the event of sensor becoming unserviceable after servicing, the contractor shall rectify the defect at his own cost.
6
-
-
... More
Taking down and refixing of Shutters of any description in same opening n exc 1sq. m each complete all as specified and directed.
4
-
-
... More
S&F in repairs Aluminium Handle 150mm long (weight not less than 120 Gram), Extruded Section, Fabricated type, anodised, complete all as specified and directed.
8
-
-
... More
S&F in repair Aluminium Barrel Tower Bolt 200mm long (weight not less than 210 Gram), Extruded Section, complete all as specified and directed.
4
-
-
... More
S&F Sheet Glass 4.0mm thick, Ordinary quality and glazing in steel windown shutter in Square exc. 0.50 Sqm in Each Pane of Windows, complete all as specified and directed.
10
-
-
... More
Hacking out old broken Glass (any thickness, size, quality or description) from Wooden or Metal Frames, glazed with putty or fixed with beads, complete all as specified and directed.
10
-
-
... More
Repairing of NCL Door, Windows, Ventilators Shutter Fixed/ Side Hang /Sliding Type including replacement of necessary Jointing Cleats, Glazing Clips, Rubber Neoprene Packing, Screws, etc. and repairing of Locking Arrangement if any, complete all as specified and directed.
NOTE : Cost of Materials required for smooth functioning of Shutter shall deem to be included in the Quoted Unit Rate.
5
-
-
... More
S&F in repair Platinum Polished, Stainless Steel Sliding Door Bolt, 250mm long having 16mm solid rod with Hasp Staple (Bolt type) and Fixing Clips of Sheet 3mm thickness complete all as specified and directed.
52
-
-
... More
S&F in repair Door Closer Aluminium (Die cast) body, hydraulically regulated, Designation No. 3, Universal type, suitable for Door Shutters of 851mm to 1000mm in width and of weight between 61.00 to 80.00 Kilogram , complete all as specified and directed.
5
-
-
... More
S&F in repair Double Action Floor Spring Hydraulically Regulated made up of minimum 1.25mm thick Aluminium alloy Sheet Foundation Box, Main Body with Stainless Steel Cover, Governing Pivot made of Brass, Other Parts made of Mild Steel heavy duty, complete all as specified and directed.
4
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements