Karnal Smart City Limited Tender

Supply & fixing of Square Type Rubber Flooring Tile’s with “ Color :Basic Black, Blue, Terracotta Red, Hunter Green,Supply of Square Type Rubber Flooring Tile’s with “Gray, Chocolate Color, Color”(Size 500 mm X500 mm) 15mm thick

Fine dressed and rubbed beige stone (from Agra) 40 mm thick, set in 12 mm thick cement coarse sand mortar. In cement coarse sand mortar 1:3 including pointing with cement motar 1:2 with an admixture of pigment to match the shade of stone.

On existing Cement Plaster wall,the surface will be cleaned to remove Dust & Dirt's before applying Water Base Cement Primer by Labourer's. After the wall dries completely sketches will be developed as specified ; with media of a Oikos/Spectrum/ Asian/ Berger/Dulux Emulsion of different colour shades by brush or paint Gun's to complete the Art work.

5’ x 5’ Security Guard Cabin OUTER STRUCTURE Base filling of MS tubular pipe of 80 mm x 40 mm, interconnecting MS pipe Top frame MS tube 80 mm X 40 mm x 2mm Pillar of MS square pipe 80mm X 40mm MS profiled sheet 1.5 mm outside on roof MS profiled sheet 1.2 mm outside on walls MS structure base frame C channel of size 3” Internal specification 5’ x5’ Guard Cabin 50 mm glass-wool insulation inside 6 mm laminated MDF board on walls and roof 18 mm commercial ply on floor Wooden batten grid framework inside for glass-wool Electrical conduit wiring ISI mark Modular switch socket 6 amp and 16 amp - 2 no. MCB and DP box for main connection LED light 18 W inside - 1 pc Ceiling fan - 1 no. Bulkhead light outside on door Male female adaptor 32amp MS Door with door closer, lock, handle - 1 no. Aluminium slider window - 3 no. AC provision - 1 no. Paint from outside as per client choice.

Back filling of good earth

Providing and fixing Nylon Carpet Tilescarpet tile flooring in all respect including all material , adhesive as per engineer includin floor level etc

Water proofing component doctor fixit

providing and fixing Stainless steel Letters over Signage board .

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of AryaBhatta in standing and propagating knowledge Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Maharshi Pingalacharya in Sukhasana Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Rishi Kanaad in standing, surrounded with physics equipments Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Maharshi Shusruta in performing operation of child on table Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Maharshi Patanjali in Surya namaskar pose Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Bhaskaracharya in Writing script on low height table in Sukhasana Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Baudhayan in Sukhasana Style upto 3 feet to 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Varahamihira in Writing script on low height table in Sukhasana Style upto 3 feet to 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Rishi Charak in grinding herbs in mortar-pestle in Sukhasana pose Style upto 3 feet to 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Mahaviracharya in Sukhasana Style upto 3 feet to 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Nagarjuna in Bending down on large vessel, working on melting something Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Bodhidharma in hand Fighting posture of kalaripayatu Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Maharshi Panini in Writing script on low height table in Sukhasana Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Rishi Agastya in Sukhasana and performing science expereiment Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of kautilya/ Chanakya in Teaching- standing and poitnig fingers Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Shivkar Bapuji Talpade in Seating- working on airplane model Style upto 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of Karna in Stretching bow and arrow in air Style to 6 feet visually interesting three-dimensional shape including 150mm thick base and dimention as per sculpture min 600x600mm ,painting & finishing of sculpture provding & instalation after final sample approval from Engineer-in-Charge

Molded/cast/carved Sculpture of FRP(Fibre Reinforced Plastic) of any precasted upto 3 Feet visually interesting three-dimensional shape ,painting & finishing of sculpture providing & installation after final sample approval from Engineer-in-Charge

Supply and fixing of jet spray for western water closet in all respect .

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Sand filling with compaction in wells complete as per level on drawing and technical specification as per clause 1209 of MoRT&H specification including all material, labour, machinery.

Constructing providing and fixing of pre-cast RCC M-40 grade circular Road Side Inspection Chamber including earthwork using sulphate resistant cement with following dia and depth cylindrical piece with 100mm wall thickness, 100mm base slab, inbuilt cover & frame on top, provision for 110mm OD in and out sewer connection with making proper in built benching and channel with PCC M-15 grade including providing cast-in-situ 100mm thick foundation of PCC M-10 grade, supplying and fixing circular precast SFRC Circular 300 mm dia manhole cover with frame - M.D. - 10, including steel reinforcement minimum @ 80kg/cum, testing for water tightness complete in all respect as per drawing, specification and the direction of the Engineer.@ every 20m

Providing and making connection to the manhole/ road side chamber/ property chamber by cutting hole in wall, making good the same with brick work/ stone masonry work in cement mortar 1:4, plaster in cement mortar 1:3, encasement of pipe at manhole with 75mm thick M15 grade concrete etc complete as directed by Engineer.

Providing, lowering, laying, aligning, fixing in position in pipe line, manually operated CI D/F Sluice valves of approved make (IS: 14846 amended upto date) PN 1.0 class of following dia complete (including jointing and jointing material) including all material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer. For 315 mm Dia HDPE pipe

Providing, lowering, laying, aligning, fixing in position at and jointing at all level/ depths ISI marked HDPE pipes of PE-100 grade and PN 6 for sewer application as per IS 14333-1996 (amended upto date) in trenches in complete including all material, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note : E/w to be measured and paid separately. 315mm dia PE 80

Automatic boom Barrier Providing & Instalation - Typically the tip of a boom gate rises in a vertical arc to a near vertical position. Boom gates are spring balanced so the pole is easily tipped. Electro-mechanical boom barriers can be operated continuously and in an intensive duty cycle. Automatic Boom Barriers offer efficient security at exit and entry points of factories, office complexes, condominiums, parking lots, toll plazas, or any roadway entry where medium to heavy traffic is expected. The boom barrier is aesthetically designed with sleek and modern looks. Its feature includes an optional anti-crush safety device, which suspends the motion of the boom, should it meet any obstruction. Optional beam sensor provides further protection to vehicles. Auto-close of the boom barrier can be programmed through the controller. Duration of fast and slow speeds is programmed at the time of installation, according to the length of the boom and frequency of traffic expected UHF Long Range Reader Two Door Reader Controller Vehicle Loop Detector Vehicle Wind Shied UHF Tag UHF RFID Hard Card Infrared safety sensor RFID Reader Software

Main LT Panel: Fabrication, supplying and installation of outdoor type cubical panel board of suitable size made out of GI sheet 2 mm thick (14 SWG) and powder coated thereafter, duly compartmentalised having door locking arrangement for protection from rain, dust, duly fixed on GI angle iron frame work of size 50 mm x 50 mm x 6 mm (NS) and having following accessories mounted inside the panel including connection, inter connection with aluminium thimbles, earthing with two nos. earth studs, duly powder coated complete etc. as required,Civil Foundation cost for the panel shall be inclusive. Cable gland plates shall be provided on bottom. 2 Nos. earthing terminals shall be provided. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. INCOMER: 400A FP MCCB, 415 V, 50 Hz. : 1 Nos Indication & digital metering BUS BARS: 400A TP + 2N Aluminium sectionalised BUS suitable for 1.1 K V with a fault level with-stand: 20 KA for 1 second. The Earth Bus shall be of AL & run contInuously throughout the width of the panel.OUTGOINGS : a) 415 V, 250 A, 4Pole, 50 Hz, MPCB : 1 Nos. b) 415 V, 63 A, 4Pole, 50 Hz, MCCB : 7 Nos. c) 415 V, 40 A, 4Pole, 50 Hz, MCB : 4 Nos. d) 20 A, DPPole, 50 Hz, MCB : 3 Nos. e) 63A TPN MCB with TVSS (Transient Voltage Surge Arrestor): 1 No.f) 40A,TP, MCB with 25KVAR AUTOMATIC CAPACITOR BANK - 1 No Indication lamps (RYB) with control MCB - 03 Sets Danger notice plate Make : As listed in UHBVNL

Smart Feeder Pillar for Lighting Control: S Supply and installation of Smart Feeder Pillar with wireless technology with Manual and Automatic ON/OFF of lights on Sunrise and Sunset time depending on the geographical location of Smart Feeder Pillar. And should enabled with facilities like Remote monitoring, Fault monitoring, System Protection, Battery back up (6hours), Energy meter etc enclosed in IP55 or above. SFP consists of following: Smart feeder panel Hardware Requirements – 1. Operating Voltage Range : 180 – 270 V 2. Smart feeder panel Capacity : 125A 3. Energy Meter : i) Smart feeder panel shall have Phase 4 Wire 10A-60A AC Energy Meter with IS:13779. ii) Energy Meter shall have built in Voltage and Current measurement sensor. No external sensors like CT or Shunts are permitted to use for Energy measurement iii) Energy Meter shall have RS232 interface to communicate with feeder communication unit (FCU) 4. Battery : 3.7 V / 0.65 Ah battery back up for RTU 5. Incomer: 1no. 125A TPN MCB & Outgoing : 5nos 25A TPN MCB 6. Contractor : 63 A Contractor 7. Street Light Gateway : Communication with server – GSM/GPRS Quad band: 850/900/1800/1900MHz; Communication method – TCP/IP Via GPRS Security - SSL ; SLG shall have built in astronomical clock for ON/OFF luminaires based on GPS locations SLG shall capable of adjusting Real Time clock based on server input and it can also support period sync based on predefined intervals. SLG Unit shall support 1 x Isolated digital output channels SLG Shall have on board Serial Communication: RS232

Control Panels for Pumps : Fabrication, supplying and installation of outdoor type cubical panel board of suitable size made out of GI sheet 2 mm thick (14 SWG) and powder coated thereafter, duly compartmentalised having door locking arrangement for protection from rain, dust, duly fixed on GI angle iron frame work of size 50 mm x 50 mm x 6 mm (NS) and having following accessories mounted inside the panel including connection, inter connection with aluminium thimbles, earthing with two nos. earth studs, duly powder coated complete etc. as required,Civil Foundation cost for the panel shall be inclusive. Cable gland plates shall be provided on bottom. 2 Nos. earthing terminals shall be provided. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Make : As listed in UHBVNL Incomer : 250A FP MPCB - 1NOS Outgoings : 125 TP Soft Indication lamps (RYB) with control MCB - 03 Sets STARTER- 4NOS Danger notice plate Make : As listed in UHBVNL

Supply & Installation of 4W LED STEP LIGHT having white powder coated cast aluminium body.Low power White LEDs (WH) covered with heat resistant frosted glass fixed to the housing with frame protection grill.LED Used shall be COB type CCT up to 5700K ±300K,IP54. An operating Voltage Range of 140 to 280V AC,PF90,50Hz. LED driver should be constant current type.The fixture should comply with the parameters as per IS10322. LUMINAIRE MAKE : Phillips / OSRAM / Wipro / Crompton / Bajaj / Havells /Surya /Keselec. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM.

Supply & Installation of 2.5W LED INGROUND UPLIGHTER having Die-cast aluminium housing with double powder coated outdoor grade and anti-UV with Specially designed fins for better heat dissipation.LED should be used of either CREE /NICHIA.System lumen of luminaire should be minimum 93lm ,CCT up to 3000K ±300K,CRI80. Luminaire should withstand having Impact resistence of IK 10 & IP 67 rating.Input voltage of DC 12V. Operating temperature range of ambient -30°C to +50°C & Lumen maintenance L70@50,000 hours at 25°C.The fixture should comply with the parameters as per S10322. LUMINAIRE MAKE : Phillips / OSRAM / Wipro / Crompton / Bajaj / Havells / Surya /Keselec. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM.

Supply & Installation 45W decorative LED Post Top having Spun aluminium powder coated finished canopy,having Die-cast aluminum graphite grey powder coated spigot & Opal acrylic diffuser provided at LED area to minimize glare.The LEDs should be Low power LED & it should be connected in series and parallel combination with better heat dissipation arrangement.LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level)=70lumens/watt,Minimum system Lumens 150 lm ±10%. CCT up to 3000K ±355K, CRI 70, PF 0.95,IP65. Luminaire is wired with inbuilt driver with 5kV surge protection and an operating Voltage Range of 140 to 280V C,50Hz. The driver should be specially designed to have high voltage, open and short circuit protection.Luminaire mounting should be Suitable for 60mm OD pipe entry with fixing bolts.The fixture should comply with the parameters as per IS10322, EMC / EMI compliance. LUMINAIRE MAKE : Phillips / OSRAM / Wipro / Crompton / Bajaj / Havells /Surya /Keselec. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM.Note:-Supply & Installation of LED fixtures. The fixtures shall be installed including supply and wiring between Weather Proof Junction Boxes to fixture with all required accessories, support clamps & interconnections etc.

Supply and installtion of 500mm length HDG 32mm dia single arm bracket suitable for 7mtr pole oct pole

Supply and installtion of 500mm length HDG 32mm dia double arm bracket suitable for 7mtr pole oct pole

Supply and installtion of 500mm length HDG 32mm dia triple arm bracket suitable for 7mtr pole oct pole

Supply & Installation of Supply of 9W LED BUSH LIGHT “SPYKZ” having Graphite grey powder coated integral aluminium housing.The Die-cast aluminium housing comprises Warm White (WW) COB LED and reflector.COB LED housing covered with die-cast aluminium ring with weatherproof gasket and toughened glass.LED Used shall be COB type CCT up to 3000K ±250K,IP65. Luminaire is wired with inbuilt driver with 5kV surge protection and an operating Voltage Range of 140 to 280V AC,PF90,50Hz.Adjustable mounting bracket with spike should be provided for easy to focus the object.2 nos., Ø8mm holes should also be provided on adjustable mounting bracket for surface mounting. LED driver should be constant current type.The fixture should comply with the parameters as per IS10322. LUMINAIRE MAKE : Phillips / OSRAM / Wipro / Crompton / Bajaj / Havells /Surya /Keselec. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM.Note:-The fixtures shall be connected with weatherproof junction box to suitable no. of luminaires as required

Supply and intallation of 30W LED flood light made of Pressure die-cast aluminium LED housing designed to act as heat sink for efficient dissipation of heat.,Heat resistant toughened glass should be provided with gasket and SS clips. LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level)=120lumens/watt, Minimum system Lumens 3,600 lm ±10%. Life of fixture 50000hrs@L70% Lumen maintenance, CCT up to 5700K ±355K, CRI 70, PF 0.95,THD10%,Operating Temperature Range-10 deg C to +45deg C, IP66 & Impact resistence of IK07. Luminaire should have built in Surge Protection of 4KV and an operating Voltage Range of 120 to 277V AC,50Hz. The driver should be specially designed to have built-in surge voltage, open/short circuit protections.Luminaire is provided with a MS mounting bracket fixed on pressure die-cast aluminium housing for aiming adjustment.The fixture should comply with the parameters as per IS10322 and IEC60598, EMC /EMI compliance. LUMINAIRE MAKE : Phillips / OSRAM / Wipro / Crompton / Bajaj / Havells /Surya /Keselec. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM.

Supply and intallation of 60W LED flood light made of Pressure die-cast aluminium LED housing designed to act as heat sink for efficient dissipation of heat.,Heat resistant toughened glass should be provided with gasket and SS clips. LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level)=120lumens/watt, Minimum system Lumens 3,600 lm ±10%. Life of fixture 50000hrs@L70% Lumen maintenance, CCT up to 5700K ±355K, CRI 70, PF 0.95,THD10%,Operating Temperature Range-10 deg C to +45deg C, IP66 & Impact resistence of IK07. Luminaire should have built in Surge Protection of 4KV and an operating Voltage Range of 120 to 277V AC,50Hz. The driver should be specially designed to have built-in surge voltage, open/short circuit protections.Luminaire is provided with a MS mounting bracket fixed on pressure die-cast aluminium housing for aiming adjustment.The fixture should comply with the parameters as per IS10322 and IEC60598, EMC /EMI compliance. LUMINAIRE MAKE : Phillips / OSRAM / Wipro / Crompton / Bajaj / Havells /Surya /Keselec. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM.

Supply and installtion of 60W Streetlight to be mounted on 7mtr poles having Epoxy powder coated pressure die‐cast aluminium housing, Weatherproof gaskets should be provided for LEDs and control gear compartments. Luminaire should be suitable for Side entry mounting for max. 38mm OD pipe bracket. The LED driver access should be from top for easy maintenance. LEDs should be provided with non‐yellowing modular secondary lens optics .LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level)=120lumens/watt, Minimum system Lumens 7200 lm ±10%. Life of fixture 50000hrs@L70% Lumen maintenance, CCT up to 5665K ±355K, CRI=70, PF=0.9,THD10%, and Operating Temperature Range-5 deg C to +45deg C, IP66. Built in Surge Protection of 4KV & external surge protection of 10kVand an operating Voltage Range of 140 to 270V AC,50Hz.Luminaire Weight should not exceed 1.5kg.The driver used is specially designed to have built‐in surge voltage, open/short circuit protections. The fixture should comply with the parameters as per IS10322 and IEC60598, EMC / EMI compliance. Bajaj Cat. Ref.ENXT P 72L WH CR PC SD or Equivalent.

Supply & Installation of 20W LED batten lights (Control room) LUMINAIRE MAKE : Phillips / OSRAM / Wipro / Crompton / Bajaj / Havells / Jaquar /Surya /Keselec. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM.

Supply and installation of 1200mm sweep ceiling fan with step electronic regulator(Make: Crompton Greaves / Bajaj/ Usha)

Weather proof Cable Junction Boxes IP 66/67 : Thermoplastics polycarbonate enclosure, shock proof, IP67 ( weather proof), rust proof, dust proof, water proof, internally embedded gasket with provision for all side cable entry through glands(IP-68) . Size of enclosure: 205 x 255 x 112 mm with suitable connecters for 3Ph/1Ph loop in loop out and branch out vibration proof connections. (KF 2525 G) with terminals. Make: Hensel/Siemens/GE Power/Rittal/ Schneider/ABB.

Air Conditioning Unit for Control room SITC 2T split AC with outdoor unit (Min 4 star rating) and stabliser Make : Hitachi / Samsung / LG/voltas

Supply and installtion of 65W LED Luminaire to be mounted on existing 5m height decorative pole. LED luminaire should be TEAR DROP model post top with spun aluminium decorative housing and clear polycarbonate diffuser with IP 65 protection. having Epoxy powder coated pressure die‐cast aluminium housing,Weatherproof gaskets should be provided for LEDs and control gear compartments.Luminaire should be suitable for cable entry and mounting on existing pole .The LED driver acces should be from top for easy maintenance.LEDs should be provided with non‐yellowing modular secondary lens optics.LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level)=120lumens/watt, Minimum system Lumens 5400 lm ±10%. Life of fixture 50000hrs@L70% Lumen maintenance, CCT up to 5665K ±355K, CRI=70, PF=0.9, THD10%, and Operating Temperature Range-5 deg C to +45deg C, IP66. Built in Surge Protection of 4KV & external surge protection of 10kVand an operating Voltage Range of 140 to 270V AC,50Hz.Luminaire Weight should not exceed 1.5kg.The driver used is specially designed to have built‐in surge voltage, open/short circuit protections.The fixture should comply with the parameters as per IS10322 and IEC60598, EMC / EMI compliance. Bajaj Cat. Ref. BNRRL 65W LED LUMINAIRE MAKE : Phillips / OSRAM / Wipro / Crompton / Bajaj / Havells /Surya /Keselec. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM.

Cleaning and PU painitng black colur on existing 5mtr decorative single arm street light column and dismantling of existing luminaire. Including replacing of damaged control cable, MCB etc make proper connection and conceal all external wire from the light coloumn.

Supply and installaion of decorative round ceiling mounted type 15W LED suspended type fixture suitable for Gazebo