Haryana State Roads And Bridges Development Corporation Limited Tender
If you want to inquire about any e-tender the Haryana government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Haryana tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Haryana etender you're looking for. Read further to learn how to search and bid for etender Haryana.
Costs
EMD
₹ 35,85,000Document Cost
₹ 20,000Tender Fee
₹ 1,180
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2021_HBC_188332_1Bid Award Id
ViewTender No
Const.of 3 lane ROB at Village Jharli LC No.27-SPLTender Authority
Haryana State Roads And Bridges Development Corporation Limited ViewPurchaser Address
-Website
http://https://haryana.gov.in/boards-and-corporations/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means as per technical clause 502 of MORT&H specifications HSR 17.25
3665
-
-
... More
Providing and applying tack coat with bitumen VG-10 using bitumen pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom as per technical clause 503 of MORT&H specifications.
HSR 17.26.1
7865
-
-
... More
Providing and laying 125 mm thick dense graded bituminous macadam (in two layers) with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG -40 @ 4.5% by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete, as per technical clause No. 505 of MORT&H specifications HSR 17.30.2
492
-
-
... More
Providing and laying 40mm thick bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG - 40 @ 5.4% per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete as per technical clause 507 of per MORTH specifications HSR 17.31.2
157
-
-
... More
Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material as per clause 304 of MORT&H specifications
HSR 15.1.2.1
1382
-
-
... More
Plain cement concrete M20 in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days as per clause 2100 of MORT&H specifications
HSR 15.8.2
91
-
-
... More
Plain cement concrete M15 in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days as per clause 2100 of MORT&H specifications
HSR 15.8.1
23
-
-
... More
Construction of Embankment with approved material obtained from borrow pits, including compensation of earth, with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2, as per technical clause 305 of MORT&H specifications. (HSR 17.6) Note:- Compensation of earth will vary from place to place and will have to be assessed realistically as per particular ground situation. In case earth is available from Govt. land, compensation for earth will not be required. The position is required to be clearly stated in the cost estimate.
1. If soil of CBR 8% is not available then the agency will do appropriate stabilization as per IRC-SP-89-2010 as approved by SE-in-Charge and nothing extra shall be paid on this account and it will be incident to work. No earth work will be allowed from PWD land.
10426
-
-
... More
Providing and fixing Reinforcement Earth retaining structure using M 40 R.C.C. precast concrete panel facing of approved design,colour and pattern and galvanised metallic strips/Geogrid in accordance with Section 3100 of Technical Specifications as per the approved suppliers design and drawing which shall be approved by the department before execution of work. The work should be executed by the expert agency under expert supervision approved by the Engineer.(Including cost of reinforcement and dowels etc)
2530
-
-
... More
Providing and laying Cement Concrete of Grade M35 in RCC Retaining Walls including centering and shuttering etc. as per Technical Specifications Section 1500,1700, 2100 and 2200
HSR 27.12.1.1
149
-
-
... More
Providing and laying Plain Cement concrete M-15 grade leveling course below approach slab as per Technical Specification Section 1500 &1700
HSR 27.45
9
-
-
... More
Providing and laying Reinforced Cement Concrete M-35 grade for approach slabs including reinforcement complete as per Technical Specifications Section 1500, 1700 and Clause 2704.
HSR 27.46
26
-
-
... More
Providing and constructing RCC crash barrier in M 40 grade including cost of centering, shuttering and Reinforcement as per Technical Specifications Clause 809 and as per IRC-6.
HSR 34.31
715
-
-
... More
Providing and constructing RCC friction slab for RE walls in M 35 grade concrete including cost of centering, shuttering as per Technical Specifications Clause 1500, 1700
HSR 27.12.1.1
329
-
-
... More
Supplying, fitting and placing HYSD bar reinforcement in sub-structure complete as per drawing and MoRT&H Specifications
HSR 27.13
42.33
-
-
... More
All Weathered Exterior Paints two coats after filling the surface with synthetic enamel paint in all shades and pattern on new concrete on exposed surfaces of Crash Barrier of ROB as per MORTH specification 803 .
857.96
-
-
... More
Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces HSR 34.49
787
-
-
... More
Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying and the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and MoRT&H Specification.
HSR 27.17
1519
-
-
... More
Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1 V :20H towards drawing force. Complete as per drawing and MoRT&H Specifications
HSR 27.15
210
-
-
... More
Service Road Providing & laying 200mm thick granular sub-base(in two layers) by providing 401 Material as per Grading Ill (Table 400-1 of MORT&H 5th revision) mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per technical clause 401 of MORT&H specifications
HSR 17.14.3
2278
-
-
... More
Providing & laying, spreading and compacting 250mm thick graded stone aggregate to wet mix macadam (in two layers) specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per technical clause 406 of MORT&H specifications
HSR 17.24
2739
-
-
... More
Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means as per technical clause 502 of MORT&H specifications HSR 17.25
10955
-
-
... More
Providing and applying tack coat with bitumen VG-10 emulsion using pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom as per technical clause 503 of MORT&H specifications.
HSR 17.26.1
21910
-
-
... More
Providing and laying 60mm thick dense graded bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG 40 @ 4.5% by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete, as per technical clause No. 505 of MORT&H specifications HSR 17.30.2
658
-
-
... More
Providing and laying 40mm thick bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG - 40 @ 5.4% per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete as per technical clause 507 of per MORTH specifications HSR 17.31.2
439
-
-
... More
Earthwork in excavation for structures of Drain complete as per Technical Specifications Clause 304 including all leads and lifts
HSR 15.1.2.1
2046
-
-
... More
Plain Cement concrete M-15 grade leveling course below drain as per Technical Specification Section 1500 &1700
HSR 15.8.1
137
-
-
... More
Reinforced cement Concrete M 35 grade for drain along service road including cost of centering, shuttering excluding reinforcement complete as per Technical Specifications Section 2700.
HSR 15.8.8.2
676
-
-
... More
Supplying, fitting and placing HYSD bar reinforcement in sub-structure complete as per drawing and MoRT&H Specifications
HSR 27.13
74
-
-
... More
Providing and laying M20 cement kerb all complete as per Technical Specifications in Kerbs
HSR 34.2.2
1240
-
-
... More
Viaduct (Bridge) Portion Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material as per clause 304 of MORT&H specifications
HSR 15.1
924
-
-
... More
Bored cast-in-situ M35 grade R.C.C. Pile 1000mm & using Hydraulic Rig excluding reinforcement complete as per Drawing and Technical Specifications and removal of excavated earth with all lifts and lead up to 1000 m MORT&H clause 1100 & 1700
HSR 15.29
930
-
-
... More
PCC M15 levelling course 100mm thick below the pile cap MORT&H clause 1100 & 1700
HSR 15.44
34
-
-
... More
Cement Concrete for Reinforced Concrete M-35 in Pile Cap complete as per Drawing and Technical Specification MORT&H clause 1100, 1500 & 1700
HSR 15.43
471
-
-
... More
Rcc In Sub Structure Reinforced cement concrete in sub- structure complete as per drawing and & 2200 MORT&H MoRT&H Specifications 1500,1700 and 2200. HSR 27.12.1.1
637
-
-
... More
Cement Concrete of Grade M40 in Pedestals & seismic arrester including centering and shuttering etc. as per Technical Specifications Section 1500,1700, 2100 and 2201
HSR 27.34.1.1
25
-
-
... More
Reinforcement in Substructures & Foundations
Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications MORT&H clause 1600.
HSR 15.45
148
-
-
... More
Supplying, fitting and placing HYSD bar reinforcement in sub-structure complete as per drawing and MoRT&H Specifications.
HSR 27.13
97
-
-
... More
PSC Girder And Cast In situ Deck slab
Providing, Casting, Stacking, Transporting and erecting Precast post tensioned PSC beams in Concrete Grade M45 for Super structure including shuttering excluding Prestressing and reinforcement complete as per Technical Specifications Section 1500, 1700 & 2300. All values for mix from batching plant
HSR 27.35.2.2
843
-
-
... More
Providing and laying Reinforced Cement Concrete of Grade M40 in deck slab, diaphragms including shuttering and staging complete as per Technical Specifications Section 1500, 1700 & 2300.(Excluding cost of steel). All values for mix from batching plant
HSR 27.33.2.2
827
-
-
... More
Supplying, fitting and placing HYSD bar reinforcement in super-structure complete as per drawing and MoRT&H specifications
HSR 27.38
247
-
-
... More
High tensile steel wires/strands including all accessories for stressing, stressing operations and grouting complete as per drawing and MoRT&H Specifications
HSR 27.39
47
-
-
... More
Providing and constructing RCC crash barrier in M 40 grade including cost of centering, shuttering and reinforcement as per Technical Specifications Clause 809 and as per IRC-6.
HSR 34.31
500
-
-
... More
Providing And laying stone matrix asphalt (SMA) 50mm thick using stablizing addatives @ 0.3% by weight of mix, hydrented lime @10% using stone aggregate 20m, 10mm with drum/batch mix plant as per standard job mix formula including additional aggregate of size 1 to 3 mm applied over the hot surface @ 1 to 2 kg/m2, immediatly after compaction and density 2.3 gm/cc and bitumen grade CRMB55 @ 5.8% by rate.Clause 515 Page 219
HSR 17.38
138
-
-
... More
Providing and laying of a strip seal expansion joint catering to maximum horizontal movement up to 70 mm, complete as per approved drawings and standard specifications to be installed by the manufacturer/supplier or their authorised representative ensuring compliance to the manufacturer's instructions for installation as per clause 2606 of MoRTH Specification (5th Revision, 2013).
HSR 27.55
144
-
-
... More
Providing Drainage Spouts as per MoRT&H specification clause 2705 with 6 meter long GI 100 mm dia drainage GI light grade pipe (For Bridges)
HSR 27.44.2
204
-
-
... More
Supplying and fixing of POT PTFE bearings complete as per Technical Specifications 2006 and IRC:83 (Part III) - 2002. The design and the supplier of the bearings shall be pre-approved by the Engineer
HSR 27.23
150 t Capacity:
Free bearing permitting sliding in both direction for Vertical Load capacity of 150 t
3000
-
-
... More
Guided bearing permitting sliding in mono directions for Vertical Load capacity of 150 t
6000
-
-
... More
Fixed bearing for Vertical Load Capacity of 150 t
3000
-
-
... More
All Weathered Exterior Paints two coats after filling the surface with synthetic enamel paint in all shades and pattern on new concrete on exposed surfaces of Crash Barrier of ROB as per MORTH specification 803 .
6531
-
-
... More
Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces HSR 34.49
550
-
-
... More
LHS
Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material as per clause 304 of MORT&H specifications
HSR 15.1.2.1
2972
-
-
... More
PCC Below Structures
Plain cement concrete M15 in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days as per clause 2100 of MORT&H specifications
HSR 15.8.1
78
-
-
... More
Plain cement concrete M20 in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days as per clause 2100 of MORT&H specifications
HSR 15.8.2
291
-
-
... More
Reinforced cement concrete in sub- structure complete as per drawing and & 2200 MORT&H MoRT&H Specifications 1500,1700and 2200.
4.32
-
-
... More
Providing and constructing RCC crash barrier in M 40 grade including cost of centering, shuttering and Reinforcement as per Technical Specifications Clause 809 and as per IRC-6.
HSR 34.31
281.81
-
-
... More
Supplying, fitting and placing HYSD bar reinforcement in sub-structure complete as per drawing and MoRT&H Specifications.
HSR 23.13
64
-
-
... More
Providing and laying M30 cement concrete wearing Course laid to required level and slope after cleaning the surface, all complete as per Technical Specifications in Underpass portion as per MORTH specification 1500,1700 and 2100.
HSR 15.8.6.1
46
-
-
... More
Providing and laying mozaic tiles on inside face of LHS to form a pattern as per approved design and colours as per instructions and satisfaction of Engineer-in-Charge confirning to IS-15477.
617
-
-
... More
All Weathered Exterior Paints two coats after filling the surface with synthetic enamel paint in all shades and pattern on new concrete on exposed surfaces of Crash Barrier of LHS as per MORTH specification 803 .
364
-
-
... More
Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces HSR 34.49
310
-
-
... More
Supplying, erection, testing and commissioning of Submersible motor pumping set non clog for sewerage having head 20.00 m as per the indicated requirements of discharge in LPM and power capacity in BHP Make: KSB, CRI, Kirlosker, Crompton Greeve, Lubi)
HSR 21.108.34
2
-
-
... More
Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire
satisfaction of Engineer- in-Charge.
HSR 24.5.1.4
200
-
-
... More
Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire
satisfaction of Engineer- in-Charge.
HSR 24.5.1
200
-
-
... More
Providing and fixing of 20 HP submersible control panel 3 conductor, volt meter, Amp. Meter, MCV, rotary switch, indicator, overload relay timer fully automotive level indicator complete in all respect.
3
-
-
... More
Design, manufacture, testing, supply, installation and commissioning of 100 KVA, 415V, 50 c/s at 0.8 PF DG set of approved make , mounted on common base frame with AMF panel, cabling, earthing with change over switch, battery including supply of battery charger with accessories and as per requirement & as per satisfaction of Engineer -in –Charge.
1
-
-
... More
Providing and constructing rain water harvesting system including earth work, C.C. works, DPC, brick work, plaster, cement rendering, steel, providing and laying of filter media (in four layers) drilling 300 mm dia bore with DTH / collax rig upto GWT of that area), Supply & lowering of 216 mm o/d ERW steel (200 mm i/d pipe), supply and lowering 166 mm o/d ERW slotted steel pipe as per IS : 4270 : 1992 & as per site requirement, supply & plowing graded MS clamp, SFRC manhole cover, plastic steps and all other works as per drawing attached & as per satisfaction of Engineer -in –Charge.
5
-
-
... More
Providing and laying 300 mm dia Class 2 UPVC pipes for drainage conforming to IS 4985 all complete as per approval and direction of Engineer .
350
-
-
... More
Providing and laying 150 mm dia Class 2 UPVC pipes for drainage conforming to IS 4985 all complete as per approval and direction of Engineer .
200
-
-
... More
Providing and fixing manhole covers in sump room with all accessories complete as per direction of Engineer as per IS 12592 : 2002
6
-
-
... More
Providing and Fixing Steel Door of size 1750mm X 750mm at Sump Room with all accessories complete as per direction of Engineer as per IS 4351
2
-
-
... More
Providing and laying 450 mm dia Class 2 UPVC pipes for drainage conforming to IS 4985 all complete as per approval and direction of Engineer .
150
-
-
... More
Providing and laying M20 cement kerb all complete as per Technical Specifications in Kerbs
HSR 34.2.2
276.91
-
-
... More
Diversion Road
Construction of Embankment, Sub- grade and earthen shoulder with material obtained from borrow pits, Construction of Embankment with approved material obtained from borrow pits, including compensation of earth, with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2, as per technical clause 305 of MORT&H specifications. (HSR 17.6) Note:- Compensation of earth will vary from place to place and will have to be assessed realistically as per particular ground situation. In case earth is available from Govt. land, compensation for earth will not be required. The position is required to be clearly stated in the cost estimate.
2. If soil of CBR 8% is not available then the agency will do appropriate stabilization as per IRC-SP-89-2010 as approved by SE-in-Charge and nothing extra shall be paid on this account and it will be incident to work. No earth work will be allowed from PWD land.
20812
-
-
... More
Providing and laying 200mm thick (in two layers) granular sub-base by providing 401 Material as per Grading Ill (Table 400-1 of MORT&H 5th revision) mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per technical clause 401 of MORT&H specifications
HSR 17.4.3
3327
-
-
... More
Providing, laying, spreading and compacting 250mm thick (in two layers) graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per technical clause 406 of MORT&H specifications
HSR 17.24
3663
-
-
... More
Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means as per technical clause 502 of MORT&H specifications HSR 17.25
14652
-
-
... More
Providing and applying tack coat with bitumen VG-10 using bitumen pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom as per technical clause 503 of MORT&H specifications.
HSR 17.26.1
29304
-
-
... More
Providing and laying 115 mm thick (in two layers) dense graded bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG 40 @ 4.5% by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete, as per technical clause No. 505 of MORT&H specifications HSR 17.30.2
1501
-
-
... More
Providing and laying 50 mm thick bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG - 40 @ 5.2% per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete as per technical clause 507 of per MORTH specifications HSR 17.31.2
605
-
-
... More
Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide Technical Specifications clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel/GI Post sections firmly fixed to the ground by means of properly designed foundation with M20 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per direction of Engineer.
60 cm equilateral triangle
2
-
-
... More
60 cm circular
2
-
-
... More
60 cm x 45 cm rectangular
2
-
-
... More
60 cm x 60 cm square
2
-
-
... More
Providing and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area about 2.5 sqm supported on a mild steel angle iron post 100 mm x 100 mm x 10 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 20 grade cement concrete 60 cm x 60 cm x 60 cm, 60 cm below ground level as per approved drawing
2
-
-
... More
Miscellaneous
Providing 100 mm dia PVC service pipe of approved quality as per IS 5831
1320
-
-
... More
Providing and laying of hot applied thermoplastic compound 2.5 mm thick including Reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. HSR 34.26
524
-
-
... More
Providing and fixing of road stud 100x 100 mm, die-cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973
220
-
-
... More
Providing and fixing of standard Metal Delineator as per IRC 79:2019 consisting of retro reflective area in white colour using Microprismatic retro reflective sheeting on each side conforming with IRC 67-2012 and meeting the coefficient of retro reflection values as per Class C table specification. The delineator shall be painted with only black colour powder coat of minimum 40 microns thickness, on top of retro reflective sheeting only in white colour shall be pasted on both sides. The structure shall have height not less than 800 mm above ground, width not less than 100 mm and shall extend not more than 300 mm below ground while being installed. The delineator shall have grooves across the length to make the reflective sheet vandal proof. The delineator is meant for application on gaps in median, traffic islands, dangerous bends, roundabouts, narrow bridges etc or as desired by site engineer. The product shall be providedwith 3 year outdoor warranty report tested inIndia condition as per IRC 67: 2012 requirement.
HSR 34.27
100
-
-
... More
Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide Technical Specifications clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel/GI Post sections firmly fixed to the ground by means of properly designed foundation with M20 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per direction of Engineer.
60 cm equilateral triangle
4
-
-
... More
60 cm circular
8
-
-
... More
60 cm x 45 cm rectangular
4
-
-
... More
60 cm x 60 cm square
4
-
-
... More
Providing and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area about 2.5 sqm supported on a mild steel angle iron post 100 mm x 100 mm x 10 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 20 grade cement concrete 60 cm x 60 cm x 60 cm, 60 cm below ground level as per approved drawing
4
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements