Government Of Haryana Tender

12 mm thick cement plaster 1:4

Conglomerate floor 40 mm thick cement concrete topping 1:2:4

Precast cement concrete 1:2:4 with stone aggregate 20 mm nominal size in Kerbs and the like items, finished smooth with 6 mm thick cement plaster 1:3 on exposed surface including from work, placing and fixing in position, complete at the ground level or in first storey.

Precast chequered tiles of 20 mm thickness in ordinary grey cement without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps and landings.

Providing & laying of 80mm thick vibratory table paver block of ISI Mark of all shapes and colour in design mix cement M-40 over a bed to 30mm thick fine sand complete in all respect

C.Conc. 1:2:4 with stone aggregate 20mm N/Size in F&P

Air Walker: Air-Walker of size 100 x 550 x 1480mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick made up of hot rolled tubular steel and hot dipped galvanized, and powder coated 80-120 micron thick usin Akzo Nobel or equivalent in desired shade and colour. All welding joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Foothold are with rounded edge to prevent impact and injury. Maintenance free bearings are used in equipment manufactured by reputed company duly sealed and self-lubricated. Equipment are fitted with inbuilt limiters. The equipment should be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover.

Air Swing: Air-Swinging p air of size 1150 x900 x1250 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are arc welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all welding points prior to finishing. Bearing used are maintained free, duly oiled, sealed and self lubricated made by reputed company. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Horse Rider Station: Horse rider station of size 1000 x 600 x 1100 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are arc welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all welding points prior to finishing. Bearings used are maintenance free, duly oiled sealed and self lubricated made by reputed. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be covered by caps for user safety.The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Stair Stepper: Stair stepper in a combination of pair and a single step of size 1000 x 800 x 1400 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are arc welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all welding points prior to finishing. Bearing used are maintenance free, duly oiled, sealed and self lubricated made by reputed company. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be covered by caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Leg Press: Leg press of size 2000 X 550 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are arc welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all welding points prior to finishing. Bearing used are maintenance free, duly oiled, sealed and self lubricated made by reputed company. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be covered by caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Double Pull Chair: Double Pull pair of size 2500 X 800 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are arc welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all welding points prior to finishing. Bearing used are maintenance free, duly oiled, sealed and self lubricated made by reputed company. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Seated Chest Press :- Seated Chest Press or Push chair of size 1800 X 700 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm

dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are arc welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all welding points prior to finishing. Bearing used are maintenance free, duly oiled sealed and self lubricated made by reputed company. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be covered by caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Arm Wheel :- Arm Wheel in a pair of size 850 X 800 X 1800 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are arc welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all welding points prior to finishing. Bearing used are maintenance free, duly oiled sealed and self lubricated made by reputed company. Equipment to be fitted within built limiters to prevent unwanted movements.

All open ends of pipe to be coloured by caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Elliptical Exerciser :- Elliptical Exerciser of size 1200 X 540 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm

thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are arc welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all welding points prior to finishing. Bearing used are shall be maintenance free, duly oiled sealed and self lubricated made by reputed company. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be covered by caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Double Cross Walker :- Double Cross Walker of size 1600 X 600 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are arc welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all welding points prior to finishing. Bearing used are maintenance free, duly oiled sealed and self lubricated made by reputed company. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Twister :- Twister of size 1700 X 1300 X 1300 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80- 120 micron thick. All welding joints of pipe are arc welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all welding points prior to finishing. Bearing

used are maintenance free, duly oiled sealed and self- lubricated. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be covered by caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Rowing Machine:- Rowing Machine of size 1280 X 800 X 1500 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are arc welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all welding points prior to finishing. Bearing used are maintenance free, duly oiled sealed and self lubricated made by reputed company. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover