Government Of Haryana Tender

31.22 Earthing. 31.22(i) Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. as required .

31.22(ii) Extra for using salt and charcoal / coke for pipe earth electrode as required.

31.22(xii) Pdg. and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required .

31.26 Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections . 31.26 (xxv) Ard. 25 Sq. mm 3.5 Core Cable .

31.26 (xI) Ard. 16 Sq. mm 4 Core Cable .

Pedestal . 31.33 Supply and erection of Godrej Almirah typeM.S.pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S.sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 31.33 (ii) M.S.pedestal of size 750 mm wide , 900 mm high , 300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster , having a base of size 1050 mm x 600 mm x 250 mm below ground level .

31.40 Supply and erection of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe. 31.40 (i) Size 1.5 sqmm ( 3/0.81 )

31.41 Supply and erection of Double door sheet steel enclosure distribution boards suitable for MCB's & ELCB's recessed in wall including bonding to earth complete with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 31.41 (v) 4-way , TP&N ( Horizontal) (8+12)

31.67 Supply and erection of mark double walled corrugated (DWC) HDPE pipe laid 1Mtr. Below ground level including diging and refilling of earth including cost of sutiable size socket/cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work. (i) HDPE pipe 63/50 mm outer dia/inner dia.

HIGH MAST POLE 31.83 (ii) Supply, installation, Testing and commissioning of 12.5 Mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 6 Nos. Luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer-in-Charge. Thickness of Top Section = 3mm (Minimum) Bottom Section =3mm (Minimum) Top Dia = 150mm Bottom Dia = 360mm Thickness of Galvanization Top = 65micron (Min.) Bottom = 85micron (Min.)

M.R. items NS-1 Supply and Erection of LED flood light fitting Crompton make LFLN-150-CDL/60 or its equivalent model of Philips BVP122 LED 146 CW FLNB FG XTFC / Bajaj BJFL 150 W / JETAPRO PLUS FL150 of Havells make with pressure dia cast alluminium housing, IP-65/66 reflector and enclosed with toughened glass with all accessories as supplied by the manufacturer including cost of all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work.

NS-2 Supply and erection of 0.3 KVA capacity inverter with SMF battery for aviation light in existing panel including the cost of labour charges and connections and petty material etc. for complete in all respect upto the entire satisfaction of Engineer-in-charge of work. Make of Invertor :- Lumineous / Microtek / Sukam - Make of Battery: Exide / Amron.

NS-3 Supply and erection of 4 way double door, sheet steel enclosure vertical type distribution board (Suitable for MCCB as incommer & MCB for out going circuit but with out cost of MCCB / MCB etc. The distribution board duly recessed in wall / surface mounting necessary connections with all labour & material required to complete the job in all respect upto the entire satisfaction of Engineer-in-charge of work.