Western Railway Tender

Providing plug point 16 Amp in concealed manner on separate board with modular accessories - The price shall cover for providing power plug point with modular type universal socket and switch, 16 Amp, 230 Volt, AC on separate board with modular accessories. The accessories shall be of 4 modular type of C&S/MK/North West/L&T/Crabtree/Siemens/Anchor/Legrand/Havells/Luminous make. The price shall also cover for concealed wiring of plug point with 2.5 sq. mm, PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 with 1.5 sq. mm, PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 as earthing wire with all accessories in concealed type of wiring in medium grade PVC conduit and accessories of Precision/Modi/Prestoplast/Gerard make.

Providing board with two switches and two sockets, 6 Amp in concealed manner with modular accessories - The price shall cover for providing multi-plug point board (switch, 6 Amp - 2 Nos and universal socket, 6 Amp - 2 Nos) with modular type universal five-pin socket and switch, 6 5 Amp, 230 Volt, AC with modular accessories. The accessories shall be of modular type of C&S/MK/North West/L&T/Crabtree/Siemens/Anchor/Legrand/Havells/Luminous make. The price shall also cover for concealed wiring of board with 1.5 sq. mm, PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 with 1.0 sq. mm, PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 as earthing wire with all accessories in concealed type of wiring in medium grade PVC conduit and accessories of Precision/Modi/ Prestoplast/Gerard make.

Concealed wiring of sub-main with 2.5 sq. mm in PVC conduit - The price shall cover for concealed wiring of sub main with two-wire single 6 core 2.5 sq. mm PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 and one wire of 1.5 sq. mm PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 in concealed manner as per site requirement in PVC conduit.

Concealed wiring of sub-main with 4.0 sq. mm in PVC conduit - The price shall cover for concealed wiring of sub main with two-wire single 7 core 4.0 sq. mm PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 and one wire of 2.5 sq. mm PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 in concealed manner as per site requirement in PVC conduit.

Wiring of light/fan/exhaust fan points in PVC casing-capping/conduit - The price shall cover for wiring of light/fan/exhaust fan point with 1.5 sq. mm, multi-stranded, PVC insulated, unsheathed FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to relevant and latest IS and 1.0 8 sq. mm, single-core, multi-stranded, PVC insulated, unsheathed FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to relevant and latest IS in medium grade PVC casing-capping double lock type, ISI marked of make Modi/Precision/Gerard/Prestoplast or medium grade PVC conduit of not less than 19 mm diameter, ISI marked of make Prestoplast/Precision/Modi/Gerard as per site conditions with surface mounted molded polypropylene switch board with modular cover plate of suitable size including switches/angular holders/ceiling rose. Space shall be kept on board to accommodate modular electronic fan regulator. Molded polypropylene switch board shall be as per IS: 14772.

Providing board with two switches and two socket, 6 Amp - The price shall cover for wiring of multi-plug point (switch, 6 Amp - 2 nos and socket, 6 Amp - 2 nos) on separate surface mounted polypropylene switch board with modular cover plate of suitable module with 2.5 sq. mm PVC 9 insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 and 1.5 sq. mm PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 as earthing wire in medium grade PVC casing capping, double lock type, ISI marked of Modi/Precision/Gerard/Prestoplast make or medium grade PVC conduit of not less than 19 mm diameter, ISI marked of make Prestoplast/Precision/Modi/Gerard as per site conditions at an approximate distance up to 3.0 meter or as per site requirement. PVC box shall be as per IS: 14772.

Wiring of sub-main with copper wire, single-core 2.5 sq. mm in PVC casing-capping/ conduit - The price shall cover for wiring of two wire 10 sub-main with 2.5 sq. mm PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 with one wire of 1.5 sq. mm PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 in medium grade PVC casing capping of not less than 25 mm size, double lock type, ISI marked of make Prestoplast/Precision/Modi/Gerard or medium grade PVC conduit of not less than 19 mm diameter, ISI marked of make Prestoplast/Precision/Modi/Gerard as per site conditions.

Tapping of light/fan point with 1.5 sq. mm copper wire with connector from existing catenary/PVC trunking - The price shall cover for 11 tapping of light/fan point with 1.5 sq. mm, PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 and one wire of 1.0 sq. mm, PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 in green colour as earthing wire in PVC flexible/rigid conduit of appropriate size from existing catenary/PVC trunking with heavy duty connector.

Wiring of sub-main with copper wire, single-core, 4.0 sq. mm - 5 Nos and 2.5 sq. mm - 1 No in PVC conduit with junction box - The price shall cover for wiring of five wire sub-main with 4.0 sq mm PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI 12 marked, conforming to IS: 694/1990 with five wires of 4.0 sq. mm PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 and one wire of 2.5 sq. mm, PVC insulated, unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 in green colour as earthing wire in medium grade PVC casing capping of not less than 25 mm size, double lock type, ISI marked of make Prestoplast/Precision/Modi/Gerard or medium grade PVC conduit of not less than 19 mm diameter, ISI marked of make Prestoplast/Precision/Modi/Gerard with heavy duty PVC junction box as per site conditions.

Providing ceiling rose with PVC junction box in existing sub-main - The price shall cover for supply and fixing of ceiling rose with PVC 13 junction box of reputed make and quality, ISI marked in existing sub-main and its connection from existing sub-main with 1.5 sq. mm multi-stranded, PVC insulated, unsheathed FRLS copper conductor and 1.0 sq. mm multi-stranded, PVC insulated, unsheathed FRLS copper conductor in green colour as earthing wire of 1100 Volt grade, ISI marked, conforming to relevant and latest IS.

Fixing, testing and commissioning of ceiling fan - The price shall cover for fixing, testing and commissioning of ceiling fan on existing hook 14 and its connection by FRPVC insulated, flexible copper cord, 1100Volt grade, 24/0.20mm from existing ceiling rose with earth connection. A suitable suspension clamp made from G.I. flat of 40 x 6 mm with MS 'S' shaped hook of diameter not less than 10 mm shall be provided as per site requirement if fan hook is not available and this is included in the scope of work. The ceiling fans shall be supplied by railways at site engineer's office/store.

Providing Exhaust fan 300 mm sweep/heavy duty with louver/bird guard - The price shall cover for supply of heavy duty, industrial Exhaust 15 Fan of metal body, 300 mm sweep with bird guard operating on 230 Volt, 50 Hz AC supply complete with all accessories of make Crompton Greaves/GEC/ Almonard/Usha/Bajaj. The price shall also cover for fixing, testing and commissioning of the Exhaust Fan on existing pocket with rake bolts/Anchor fasteners of suitable size as per site condition, and its connection from existing ceiling rose with three-core, 24/0.20 mm size, FRPVC insulated, flexible copper wire of 1100 Volt grade.

Providing PVC junction box with eight-way connector - The price shall cover for supply and fixing of PVC junction box with eight way 16 connector of reputed make and quality, ISI marked in existing sub-main and its connection from existing sub-main with 1.5 sq. mm multi-stranded, PVC insulated, unsheathed FRLS copper conductor and 1.0 sq. mm multi-stranded, PVC insulated, unsheathed FRLS copper conductor in green colour as earthing wire of 1100 Volt grade, ISI marked, conforming to relevant and latest IS.

Providing 20 Amp ray roll plug and socket with MCB DP, 16/20 Amp in weather proof box - The price shall cover for supply, erection, 17 testing and commissioning of power plug board with one MCB DP 16/20 Amp, ray-roll socket 16/20 Amp and LED indication lamp in weather proof MS enclosure. The MCB shall be of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/CGL/Schneider make. The colour of MS enclosure should be in sync with the decor of the room and as decided by site engineer. The MS enclosure shall be properly earthed.

Providing Distribution Board with incomer MCB DP, 16/32 Amp - 1 No, RCBO, 25 Amp - 1 No and outgoing MCB SP, 6/10/16 Amp - 2 Nos - The price shall cover for supply, fixing, testing and commissioning of pre-fabricated, double door, MCB distribution board fabricated from CRCA sheet steel, powder coated with grey finish, dust and vermin proof, water resistant with metallic door complete with MCBs of 10 KA breaking capacity. The 18 Distribution Board shall be equipped with incomer MCB DP, 16/32 Amp - 1 No, RCBO, two-pole, 30 mA sensitivity, 25 Amp - 1 No and outgoing MCB SP, 6/10/16 Amp - 2 Nos. The MCBs/RCBOs shall be of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/ Schneider/CGL/Havells make. The board shall be completely wired with multi-stranded copper wire of suitable capacity and shall be provided with heavy duty connectors of suitable capacity for termination of incoming and outgoing wires and shall be provided with two nos of earthing terminals on each side of the board and riveted metallic caution board in three languages. The Distribution Board shall be suitable for surface/recessed mounting as per site requirement.

Providing lighting control board with MCB DP, 32 Amp - 1 No, Time Switch, 16 Amp - 1 No and Single Phase Contactor, 32 Amp - 1 No - The price shall cover for supply, fixing, testing and commissioning of lighting control board fabricated from CRCA sheet steel, powder coated with grey finish, dust and vermin proof, water resistant with metallic door complete with MCBs of 10 KA breaking capacity. The board shall be equipped with MCB DP, 10 19 KA breaking capacity, 32 Amp rating - 1 No, Time switch, 16 Amp - 1 No and Single phase contactor of rating 32 Amp - 1 No. The MCB shall be of ABB/L&T (Hagar)/ HPL/GE/MDS/Siemens/BCH/C&S/Schneider/CGL/Havells make, the contactor shall be of L&T/BCH/C&S/ CGL/Schneider/Siemens make and Digital Time Switch "CRONO" of L&T make or similar of Siemens/Minilec make. The board shall be completely wired with multi-stranded copper wire of suitable capacity and shall be provided with heavy duty connectors of suitable capacity for termination of incoming and outgoing wires and shall be provided with two nos of earthing terminals on each side of the board and riveted metallic caution board in three languages.

Providing lighting control board with MCB DP 32 Amp - 2 Nos, Time switch, 16 Amp - 2 Nos and single-phase contactor, 32 Amp - 2 Nos - The price shall cover for supply, fixing, testing and commissioning of lighting control board fabricated from CRCA sheet steel, powder coated with grey finish, dust and vermin proof, water resistant with metallic door complete with MCBs of 10 KA breaking capacity. The board shall be equipped with MCB 20 DP, 10 KA breaking capacity, 32 Amp rating - 2 Nos, Time switch, 16 Amp - 2 Nos and single-phase contactor of rating 32 Amp - 2 Nos. The MCB shall be of ABB/L&T (Hagar)/ HPL/GE/MDS/Siemens/BCH/C&S/Schneider/CGL/Havells make, the contactor shall be of L&T/BCH/C&S/ CGL/Schneider/Siemens make and Digital Time Switch "CRONO" of L&T make or similar of Siemens/Minilec make. The board shall be completely wired with multi-stranded copper wire of suitable capacity and shall be provided with heavy duty connectors of suitable capacity for termination of incoming and outgoing wires and shall be provided with two nos of earthing terminals on each side of the board and riveted metallic caution board in three languages.

Providing Distribution Board with incomer MCB DP, 16/32 Amp - 1 No, RCBO, 25 Amp - 1 No and outgoing MCB DP, 6/10/16 Amp - 4 Nos - The price shall cover for supply, fixing, testing and commissioning of pre-fabricated, double door, MCB distribution board fabricated from CRCA sheet steel, powder coated with grey finish, dust and vermin proof, water resistant with metallic door complete with MCBs of 10 KA breaking capacity. The 21 Distribution Board shall be equipped with incomer MCB DP, 16/32 Amp - 1 No, RCBO, two-pole, 30 mA sensitivity, 25 Amp - 1 No and outgoing MCB DP, 6/10/16 Amp - 4 Nos. The MCBs/RCBOs shall be of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/Schneider/CGL/Havells make. The board shall be completely wired with multi-stranded copper wire of suitable capacity and shall be provided with heavy duty connectors of suitable capacity for termination of incoming and outgoing wires and shall be provided with two nos of earthing terminals on each side of the board and riveted metallic caution board in three languages. The Distribution Board shall be suitable for surface/recessed mounting as per site requirement.

Providing lighting control board with incomer MCB TPN, 32 Amp - 1 No, outgoing MCB DP, 16/20/32 Amp - 4 Nos, Time switch, 16 Amp - 3 Nos and Single-phase contactor, 32 Amp - 3 Nos - The price shall cover for supply, fixing, testing and commissioning of lighting control board fabricated from CRCA sheet steel, powder coated with grey finish, dust and vermin proof, water resistant with metallic door complete with MCBs of 10 KA breaking 22 capacity. The board shall be equipped with incomer MCB TPN, 10 KA breaking capacity, 32 Amp rating - 1 No, Time switch, 16 Amp - 3 Nos, Single-phase contactor of rating 32 Amp - 3 Nos and outgoing MCB DP, 16/20/32 Amp - 4 Nos. The MCBs shall be of ABB/L&T (Hagar)/HPL/ GE/MDS/Siemens/BCH/C&S/Schneider/CGL/Havells make, the contactor shall be of L&T/BCH/C&S/CGL/ Schneider/Siemens make and Digital Time Switch "CRONO" of L&T make or similar of Siemens/Minilec make. The board shall be completely wired with multi-stranded copper wire of suitable capacity and shall be provided with heavy duty connectors of suitable capacity for termination of incoming and outgoing wires and shall be provided with two nos of earthing terminals on each side of the board and riveted metallic caution board in three languages.

Providing Distribution Board wall mounted with incomer MCB, TPN, 63 Amp - 1 No and outgoing MCB DP, 16/20/32 Amp - 6 Nos with Time Switch, 16 Amp - 1 No and single-phase contactor, 16 Amp - 1 No - The price shall cover for supply, fixing, testing and commissioning of Distribution Board fabricated from CRCA sheet steel, powder coated with grey finish, dust and vermin proof, water resistant with metallic door complete with MCBs of 23 10 KA breaking capacity. The board shall be equipped with incomer MCB TPN, 10 KA breaking capacity, 63 Amp rating - 1 No and outgoing MCB DP, 16/20/32 Amp - 6 Nos, Time switch, 16 Amp - 1 No and single-phase contactor of rating 16 Amp - 1 No. The MCBs shall be of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/Schneider/CGL/Havells make. The Single-phase contactor shall be of L&T/BCH/C&S/CGL/Schneider/Siemens make and Digital Time Switch "CRONO" of L&T make or similar of Siemens/Minilec make. The board shall be completely wired with multi-stranded copper wire of suitable capacity and shall be provided with heavy duty connectors of suitable capacity for termination of incoming and outgoing wires and shall be provided with two nos of earthing terminals on each side of the board and riveted metallic caution board in three languages.

Providing Distribution Board with incomer MCB TPN, 63 Amp - 1 No and outgoing MCB DP, 16/20/32 Amp - 6 Nos with Time Switch, 16 Amp 24 - 2 Nos and Single Phase Contactor, 32 Amp - 2 Nos - The price shall cover for supply, fixing, testing and commissioning of Distribution Board fabricated from CRCA sheet steel, powder coated with grey finish, dust and vermin proof, water resistant with metallic door complete with MCBs of 10 KA breaking capacity. The board shall be equipped with incomer MCB TPN, 10 KA breaking capacity, 63 Amp rating - 1 No, Time switch, 16 Amp - 2 Nos and Single- phase contactor of rating 16 Amp - 2 Nos. The MCBs shall be of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/Schneider /CGL/Havells make. The single-phase contactor shall be of L&T/BCH/C&S/CGL/Schneider/Siemens make and Digital Time Switch "CRONO" of L&T make or similar of Siemens/Minilec make. The board shall be completely wired with multi-stranded copper wire of suitable capacity and shall be provided with heavy duty connectors of suitable capacity for termination of incoming and outgoing wires and shall be provided with two nos of earthing terminals on each side of the board and riveted metallic caution board in three languages.

Providing Distribution Board, double-door, with incomer MCCB, four-pole, 63 Amp - 1 No and outgoing MCB DP, 20/32 Amp - 10 Nos - The price shall cover for fabrication, supply, fixing, testing and commissioning of outdoor type LT distribution board fabricated from 18 SWG CRCA sheet steel, powder coated with grey enamel, double door, wall/floor mounted, dust and vermin proof, water resistant type confirming to relevant IS and complete with MCCBs and MCBs. The board shall be fabricated for three-phase, four-wire, 440 Volt AC, 50 Hz supply system and shall consist of the following switchgears/ accessories - (a) Incomer - MCCB, four-pole, 63 Amp with thermal-magnetic release range 50 - 63 Amp, Ics = 100% Icu having 35 KA breaking capacity and conforming to IS/IEC 60947-2 with adjustable overload and short circuit settings and inbuilt instantaneous protection of 25 ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/ Schneider/CGL/Havells make. The MCCB shall be supplied with spreader terminals and rotary handle --- 1 No RCBO, four-pole, 40 Amp, 30 mA sensitivity conforming to IS 12640 (Part 1)/IEC 61008-1 of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/Schneider/CGL/Havells make --- 1 No (b) Outgoing - MCB DP, 10 KA breaking capacity, 20/32 Amp of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/ Schneider/CGL/Havells make --- 10 Nos (c) Bus bar for main circuit and neutral shall have uniform cross section and made from electrolytic tinned copper as per relevant standards with colour coded, heat shrinkable, PVC insulated and having current density of 1.6 Amp/sq. mm cross sectional area --- 1 set (d) Multi LED type indication lamp for three-phases (Red, Yellow and Blue) with protection fuses of L&T/ C&S/BCH/Schneider/Siemens make --- 1 Set (e) Cable glands and cable lugs of required sizes --- LOT (f) Two earth terminals of 12 mm diameter G.I. nut/bolt with washers shall be provided in the LT panel and all sheet steel section shall be electrically connected with a separate G.I. earth strip of 50 x 6 mm size across the panel at bottom. (g) Metallic Caution Board in three languages riveted to the panel board --- 2 Nos

Providing Distribution Board with incomer MCCB, four-pole, 63 Amp - 1 No, RCBO, four-pole, 40 Amp - 1 No and outgoing MCB TPN, 32 Amp - 2 and MCB DP, 16/32 - 6 Nos - The price shall cover for fabrication, supply, fixing, testing and commissioning of outdoor type LT distribution board fabricated from 18 SWG CRCA sheet steel, powder coated with grey enamel, double door, wall/floor mounted, dust and vermin proof, water resistant type confirming to relevant IS and complete with MCCBs and MCBs. The board shall be fabricated for three-phase, four-wire, 440 Volt AC, 50 Hz supply system and shall consist of the following switchgears/accessories - (a) Incomer - MCCB, four-pole, 63 Amp with thermal-magnetic release range 50 - 63 Amp, Ics = 100% Icu having 35 KA breaking capacity and conforming to IS/IEC 60947-2 with adjustable overload and short circuit settings and inbuilt instantaneous protection of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/ Schneider/CGL/Havells make. The MCCB shall be supplied with spreader 26 terminals and rotary handle --- 1 No RCBO, four-pole, 40 Amp, 30 mA sensitivity conforming to IS 12640 (Part 1)/IEC 61008-1 of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/ C&S/CGL/Schneider/Havells make --- 1 No (b) Outgoing - MCB TPN, 10 KA breaking capacity, 32 Amp of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/ Schneider/CGL/Havells make --- 2 Nos MCB DP, 10 KA breaking capacity, 16/32 Amp of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/ Schneider/CGL/Havells make --- 6 Nos (c) Bus bar for main circuit and neutral shall have uniform cross section and made from electrolytic tinned copper as per relevant standards with colour coded, heat shrinkable, PVC insulated and having current density of 1.6 Amp/sq. mm cross sectional area --- 1 set (d) Multi LED type indication lamp for three-phases (Red, Yellow and Blue) with protection fuses of L&T/ C&S/BCH/Schneider/Siemens make --- 1 Set (e) Cable glands and cable lugs of required sizes --- LOT (f) Two earth terminals of 12 mm diameter G.I. nut/bolt with washers shall be provided in the LT panel and all sheet steel section shall be electrically connected with a separate G.I. earth strip of 50 x 6 mm size across the panel at bottom. (g) Metallic Caution Board in three languages riveted to the panel board --- 2 Nos

Providing Distribution Board with incomer MCB TPN, 32 Amp - 1 No and outgoing MCB DP, 16 Amp - 8 Nos with Single Phase Contactor, 16 Amp - 4 Nos and Time Switch, 16 Amp - 4 Nos for 30% and 70% lighting control - The price shall cover for supply, fixing, testing and commissioning of Distribution Board fabricated from CRCA sheet steel, powder coated with grey finish, dust and vermin proof, water resistant with metallic door complete 27 with MCBs of 10 KA breaking capacity. The board shall be equipped with incomer MCB TPN, 10 KA breaking capacity, 32 Amp rating - 1 No and outgoing MCB DP, 16 Amp - 8 Nos, Time switch, 16 Amp - 4 Nos and Single-phase contactor of rating 16 Amp - 4 Nos. The MCBs shall be of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/Schneider/CGL/Havells make. The single-phase contactor shall be of L&T/BCH/C&S/CGL/Schneider/Siemens make and Digital Time Switch "CRONO" of L&T make or similar of Siemens/Minilec make. The board shall be completely wired with multi-stranded copper wire of suitable capacity and shall be provided with heavy duty connectors of suitable capacity for termination of incoming and outgoing wires and shall be provided with two nos of earthing terminals on each side of the board and riveted metallic caution board in three languages.

Providing outdoor type, double-door, Distribution Board with incomer MCCB, four-pole, 63 Amp - 1 No, RCBO, four-pole, 63 Amp - 1 No and outgoing MCB DP, 16/20/32 Amp - 8 Nos - The price shall cover for fabrication, supply, fixing, testing and commissioning of outdoor type, double-door, Distribution Board fabricated from 18 SWG CRCA sheet steel, powder coated with grey enamel, double door, wall/floor mounted, dust and vermin proof, water resistant confirming to relevant IS and complete with MCCBs and MCBs. The board shall be fabricated for three-phase, four-wire, 440 Volt AC, 50 Hz supply system and shall consist of the following switchgears/accessories - (a) Incomer - MCCB, four-pole, 63 Amp with thermal-magnetic release range 50 - 63 Amp, Ics = 100% Icu having 35 KA breaking capacity and conforming to IS/IEC 60947-2 with adjustable overload and short circuit settings and 28 inbuilt instantaneous protection. The MCCB shall be supplied with spreader terminals and rotary handle. The MCCB shall be of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/Schneider/ CGL/Havells make --- 1 No RCBO, four-pole, 63 Amp, 30 mA sensitivity conforming to IS 12640 (Part 1)/IEC 61008-1 of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/Schneider/CGL/Havells make --- 1 No (b) Outgoing - MCB DP, 10 KA breaking capacity, 16/20/32 Amp of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/ C&S/Schneider/CGL/Havells make --- 8 Nos (c) Bus bar for main circuit and neutral shall have uniform cross section and made from electrolytic tinned copper as per relevant standards with colour coded, heat shrinkable, PVC insulated and having current density of 1.6 Amp/mm2 cross sectional area --- 1 set (d) Multi LED type indication lamp for three-phases (Red, Yellow and Blue) with protection fuses of L&T/ C&S/BCH/Schneider/Siemens make --- 1 Set (e) Cable glands and cable lugs of required sizes --- LOT (f) Two earth terminals of 12 mm diameter G.I. nut/bolt with washers shall be provided in the LT panel and all sheet steel section shall be electrically connected with a separate G.I. earth strip of 50 x 6 mm size across the panel at bottom. (g) Metallic Caution Board in three languages riveted to the panel board --- 2 Nos

Providing Distribution Board, double-door, wall/floor mounted with incomer MCCB, four-pole, 100 Amp - 1 No and outgoing MCB TPN, 63 Amp - 2 Nos, MCB DP, 63 Amp - 2 Nos and MCB DP, 16/20 Amp - 6 Nos - The price shall cover for fabrication, supply, fixing, testing and commissioning of Distribution Board fabricated from 18 SWG CRCA sheet steel, powder coated with grey enamel, double door, wall/floor mounted, dust and vermin proof, water resistant confirming to relevant IS and complete with MCCBs and MCBs. The board shall be fabricated for three-phase, four-wire, 440 Volt AC, 50 Hz supply system and shall consist of the following switchgears/accessories - (a) Incomer - MCCB, four-pole, 100 Amp with thermal-magnetic release range 80 - 100 Amp, Ics = 100% Icu having 35 KA breaking capacity and conforming to IS/IEC 60947-2 with adjustable overload and short circuit settings 29 and inbuilt instantaneous protection. The MCCB shall be supplied with spreader terminals and rotary handle. The MCCB shall be of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/Schneider/ CGL/Havells make --- 1 No (b) Outgoing - MCB TPN, 10 KA breaking capacity, 32/40 Amp of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/ C&S/Schneider/ CGL/Havells make --- 2 Nos MCB DP, 10 KA breaking capacity, 25/32 Amp of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/ C&S/Schneider/ CGL/Havells make --- 6 Nos (c) Bus bar for main circuit and neutral shall have uniform cross section and made from electrolytic tinned copper as per relevant standards with colour coded, heat shrinkable, PVC insulated and having current density of 1.6 Amp/sq mm cross sectional area --- 1 set (d) Multi LED type indication lamp for three-phases (Red, Yellow and Blue) with protection fuses of L&T/ C&S/BCH/Schneider/Siemens make --- 1 Set (e) Cable glands and cable lugs required sizes --- LOT (f) Two earth terminals of 12 mm diameter G.I. nut/bolt with washers shall be provided in the LT panel and all sheet steel section shall be electrically connected with a separate G.I. earth strip of 50 x 6 mm size across the panel at bottom. (g) Metallic Caution Board in three languages riveted to the panel board --- 2 Nos

Providing Distribution Board with incomer MCCB, four-pole, 100 Amp - 1 No and outgoing MCCB, four-pole, 63 Amp - 2 Nos and MCB TPN, 32 Amp - 2 Nos - The price shall cover for fabrication, supply, fixing, testing and commissioning of Distribution Board fabricated from 18 SWG CRCA sheet steel, powder coated with grey enamel, wall/floor mounted, dust and vermin proof, water resistant confirming to relevant IS and complete with MCCBs and MCBs. The board shall be fabricated for three-phase, four-wire, 440 Volt AC, 50 Hz supply system and shall consist of the following switchgears/ accessories - (a) Incomer - MCCB, four-pole, 100 Amp with thermal-magnetic release range 80 - 100 Amp, Ics = 100% Icu having 35 KA breaking capacity and conforming to IS/IEC 60947-2 with adjustable overload and short circuit settings and inbuilt instantaneous protection. The MCCB shall be supplied with spreader terminals and rotary handle. The MCCB shall be of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/Schneider/ CGL/Havells make --- 1 No 30 (b) Outgoing - MCCB, four-pole, 63 Amp with thermal-magnetic release range 50 - 63 Amp, Ics = 100% Icu having 35 KA breaking capacity and conforming to IS/IEC 60947-2 with adjustable overload and short circuit settings and inbuilt instantaneous protection. The MCCB shall be supplied with spreader terminals and rotary handle. The MCCB shall be of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/Schneider/ CGL/Havells make --- 2 Nos MCB TPN, 10 KA breaking capacity, 32 Amp of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/ Schneider/CGL/Havells make --- 2 Nos (c) Bus bar for main circuit and neutral shall have uniform cross section and made from electrolytic tinned copper as per relevant standards with colour coded, heat shrinkable, PVC insulated and having current density of 1.6 Amp/sq mm cross sectional area --- 1 set (d) Multi LED type indication lamp for three-phases (Red, Yellow and Blue) with protection fuses of L&T/ C&S/BCH/Schneider/Siemens make --- 1 Set (e) Cable glands and cable lugs required sizes --- LOT (f) Two earth terminals of 12 mm diameter G.I. nut/bolt with washers shall be provided in the LT panel and all sheet steel section shall be electrically connected with a separate G.I. earth strip of 50 x 6 mm size across the panel at bottom. (g) Metallic Caution Board in three languages riveted to the panel board --- 2 Nos

Providing Distribution Board, outdoor type, double-door, wall/floor mounted with incomer MCCB, four-pole, 100 Amp - 2 Nos and outgoing MCB TPN, 32/40 Amp - 2 Nos, MCB DP, 25/32 Amp - 8 Nos with Time Switch, 16 Amp - 2 Nos and single-phase contactor, 16 Amp - 2 Nos - The price shall cover for fabrication, supply, fixing, testing and commissioning of outdoor type, double-door, Distribution Board fabricated from 18 SWG CRCA sheet steel, powder coated with grey enamel, wall/floor mounted, dust and vermin proof, water resistant confirming to relevant IS and complete with MCCBs and MCBs. The board shall be fabricated for three-phase, four-wire, 440 Volt AC, 50 Hz supply system and shall consist of the following switchgears/accessories - (a) Incomer - MCCB, four-pole, 100 Amp with thermal-magnetic release range 80 - 100 Amp, Ics = 100% Icu having 35 KA 31 breaking capacity and conforming to IS/IEC 60947-2 with adjustable overload and short circuit settings and inbuilt instantaneous protection. The MCCBshall be supplied with spreader terminals and rotary handle. The MCCB shall be of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/C&S/Schneider/ CGL/Havells make --- 2 Nos (b) Outgoing - MCB TPN, 10 KA breaking capacity, 32/40 Amp of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/ C&S/CGL/Schneider/Havells make --- 2 Nos MCB DP, 10 KA breaking capacity, 25/32 Amp of ABB/L&T (Hagar)/HPL/GE/MDS/Siemens/BCH/ C&S/CGL/Schneider/Havells make --- 8 Nos (c) Single phase contactor of rating 16 Amp of L&T/Siemens/Minilec make --- 2 Nos (d) Digital time switch, daily dial type, 16 Amp model "CRONO" of L&T make or similar of Siemens/Minilec make --- 2 Nos (e) Bus bar for main circuit and neutral shall have uniform cross section and made from electrolytic tinned copper as per relevant standards with colour coded, heat shrinkable, PVC insulated and having current density of 1.6 Amp/sq. mm cross sectional area --- 1 set (f) Multi LED type indication lamp for three-phases (Red, Yellow and Blue) with protection fuses of L&T/ C&S/BCH/Schneider/Siemens make --- 1 Set (g) Cable glands and cable lugs required sizes --- LOT (h) Two earth terminals of 12 mm diameter G.I. nut/bolt with washers shall be provided in the LT panel and all sheet steel section shall be electrically connected with a separate G.I. earth strip of 50 x 6 mm size across the panel at bottom. (i) Metallic Caution Board in three languages riveted to the panel board --- 2 Nos

Digging of cable trench 450/600 mm wide and 900 mm deep in all types of soil including hard, rocky etc. - The price shall cover for digging of 450/600 mm wide and 900 mm deep trench in all types of soil including soft, rocky as per cable route plan and filling back the trench after laying of cables. This also includes clearing of roots of trees and bushes and other temporary obstructions on the selected route.

Digging of cable trench 100 mm wide and 200 mm deep in concrete/tar road/platform and refilling to its original position after laying of 33 cable in HDPE pipe, 50 mm diameter - The price shall cover for digging of cable trench of size 100 x 200 mm deep in concrete/tar road/platform surface and its refilling/plastering after laying of cable in 50 mm diameter HDPE pipe of Tijaria/Himalyan/Koncept/Poddar/ Unique/Dutron/Reliance/Baba/Shivam make in existing trench. Supply and laying of HDPE pipe, 50 mm diameter is included in the scope of work.

Digging of cable trench 200 mm wide and 200 mm deep in concrete/tar road/platform and refilling to its original position after laying of 34 cable in HDPE pipe, 110 mm diameter - The price shall cover for digging of cable trench of size 200 x 200 mm deep in concrete/tar road/platform surface and its refilling/plastering after laying of cable in 110 mm diameter HDPE pipe of Tijaria/Himalyan/Koncept/ Poddar/Unique/Dutron/Reliance/Baba/Shivam make in existing trench. Supply and laying of HDPE pipe, 110 mm diameter is included in the scope of work.

Supply and laying of RCC half round pipe, 100 mm diameter - The price shall cover for supply of half round RCC pipes of 100 mm inner 35 diameter and 1.0 meter in length as per description given in Annexure-XX of tender document. The internal surface shall have a smooth finish without any bulge or projections to avoid damage to the cable. The price shall also cover for laying of half round RCC pipes above the cables for mechanical protection on laid cables in the existing trench. After laying of RCC half round pipe, the trench shall be filled up with soil available thereby.

Supply and laying of RCC half round pipe, 150 mm diameter - The price shall cover for supply of half round RCC pipes of 150 mm inner 36 diameter and 1.0 meter in length as per description given in Annexure-XX of tender document. The internal surface shall have a smooth finish without any bulge or projections to avoid damage to the cable. The price shall also cover for laying of half round RCC pipes above the cables for mechanical protection on laid cables in the existing trench. After laying of RCC half round pipe, the trench shall be filled up with soil available thereby.

Supply and laying of DWC pipe, 63 mm diameter - The price shall cover for supply of Double Wall Corrugated (DWC) HDPE pipe of 63 mm 37 diameter. DWC HDPE pipe shall have corrugation on outer wall but inner wall shall be plain conforming to IS: 14930 Part I and II amended from time to time. The pipes shall be "ISI" marked. Accessories like HDPE snap fit coupler with neoprene 'O' ring shall be part of supply to make the joints water/damp proof. The strength and stiffness class of the pipe shall be SN4 and SN8 respectively. The DWC pipe shall be of SUPREME/ASTRAL/DUTRON make or any other make approved by Sr. DEE (Power) Vadodara as per IS mentioned above. The price shall also cover for laying the DWC pipes in existing trench.

Supply and laying of DWC pipe, 120 mm diameter - The price shall cover for supply of Double Wall Corrugated (DWC) HDPE pipe of 120 mm diameter. DWC HDPE pipe shall have corrugation on outer wall but inner wall shall be plain conforming to IS: 14930 Part I and II amended from time 38 to time. The pipes shall be "ISI" marked. Accessories like HDPE snap fit coupler with neoprene 'O' ring shall be part of supply to make the joints water/damp proof. The strength and stiffness class of the pipe shall be SN4 and SN8 respectively. The DWC pipe shall be of SUPREME/ASTRAL/DUTRON make or any other make approved by Sr. DEE (Power) Vadodara as per IS mentioned above. The price shall also cover for laying the DWC pipes in existing trench.

Providing uPVC pipe, 50 mm diameter - The price shall cover for supply of uPVC pipe of 50 mm nominal bore diameter and working pressure of 14 kg/sq. cm along with coupling, elbow, tee etc for protection of cable. The upright cable shall be encased in uPVC pipes for mechanical 39 protection. The pipe shall be clamped with flat MS clamp at each location on upright cable length. uPVC Pipe shall be as per ASTM-D: 1785, Sch-80 of PARIXIT/SWASTIK/ASHIRWAD/ASTRAL/DOLPHIN/POLYTECH/DUKE/FALCON make. The price shall also cover for laying the uPVC pipes in ground/road and under the track by digging open trench method. Each length of the pipes shall be joined together using proper size of uPVC coupler and properly aligned in a straight line, keeping an inclination to facilitate the draining of water.

Supply and laying of HDPE pipe, 110 mm diameter by pushing method under track/road - The price shall cover for supply of HDPE (High Density Polyethylene) pipe of 110 mm nominal diameter as per IS 4984-1995 of make Tijaria/Himalyan/Koncept/Poddar/Unique/Dutron/Reliance/Baba/Shivam with accessories required for laying such as coupler, bend etc. as per description 40 given in Annexure-XX of tender document. The price shall also cover for laying the HDPE pipes in the ground below the tracks/road by push through method at a depth below the formation level as indicated in the drawing supplied by railway. The term "formation" level means the earth surface just below the bedding of the ballast. In case of any hard/stony soil, contractor should adopt new technology method in push through method. Each length of the pipes shall be joined together properly using proper size of socket and aligned in a straight line, keeping an inclination to facilitate the draining of water.

Providing G.I. perforated cable tray of size 150 mm x 100 mm x 100 mm on MS frame with cover - The price shall cover for fabrication, supply and fixing of M.S. perforated cable tray, hot dip galvanized as per latest ISS/BSS of size 150 x 100 x 100 mm and 2.0 mm approximate thickness 41 with appropriate cover of thickness 1.6 mm. The cable tray shall be fixed horizontally or vertically at site and the existing LT cables shall be laid/shifted in the cable tray by disconnecting from the panel/switch end and reconnecting as per site requirement duly tied with suitable clamps with GI nuts, bolts and washers in a safe and secure manner. The fixing clamps shall be fabricated from 50 x 50 x 6 mm MS angle or 50 x 6 mm MS flat duly painted and fixed at approximate distance of 1.5 to 2.0 meter apart with 2" long dowel/fisher rack bolts. The tray shall be fabricated in lengths of 2.0 m and couplers shall be provided at joints. The cable tray cover shall be fixed with GI screws.

Laying of cable in trench - The price shall cover for laying, testing and commissioning of LTUG armoured cable in existing trench/pipe and 42 its connection at both ends. The cable shall be tested with 500 Volt Megger earth tester before laying it in the trench. The cable cores shall be tested for continuity, absence of cross phasing, Insulation Resistance between conductors to earth/armour and between conductors. The results should be recorded in presence of railways' representative. A composite cable layout plan on ferro-print or computerized print duly laminated in A-4 size should be submitted by the contractor to this office as well as site in-charge after laying of cable. Cables shall be supplied by railways at site engineer's stores.

Laying of cable on wall/cover shed/existing tray with MS clamp - The price shall cover for laying, testing and commissioning of LTUG 43 armoured cable on wall/cover shed/in existing tray and its connection at both ends. The cable shall be tested with 500 Volt Megger before laying it in the tray. The cable cores shall be tested for continuity, absence of cross phasing, Insulation Resistance between conductors to earth/armour and between conductors. The results should be recorded in presence of railways' representative. A composite cable layout plan on ferro-print or computerized print duly laminated in A-4 size should be submitted by the contractor to site engineer and Divisional Office after laying of cable.

Supply, fixing, testing and commissioning of 5.0 meter height G.I. street light octagonal pole, single arm complete with all accessories and foundation - The price shall cover for supply, erection and commissioning of 5.0 meter height single arm, G.I. street light octagonal pole as per the below 44 mentioned specifications. G.I. Octagonal pole of 5.0 meter height, Top - 70 mm diameter, Bottom - 130 mm diameter and 3 mm thickness sheet. Base plate of minimum dimension 200 x 200 x 12 mm, foundation bolts (4 Nos with 3 Nos of nuts and washers in each), single arm bracket for mounting the light fittings, Bakelite sheet with one MCB SP, 6 Amp and 16 sq. mm stud type connector (4 Nos) inside the pole at door opening for cable connection, common templates minimum for 15 poles. Detailed specifications of Galvanized Octagonal poles are given in Annexure-XX of tender document.

Supply, fixing, testing and commissioning of 5.0 meter height G.I. street light octagonal pole, double arm complete with all accessoriesand foundation - The price shall cover for supply, erection and commissioning of 5.0 meter height double arm, G.I. street light octagonal pole as per the below mentioned specifications. G.I. Octagonal pole of 5.0 meter height, Top - 70 mm diameter, Bottom - 130 mm diameter and 3 mm thickness sheet. Base plate of minimum dimension 200 x 200 x 12 mm, foundation bolts (4 Nos with 3 Nos of nuts and washers in each), single arm bracket for mounting the light fittings, Bakelite sheet with one MCB SP, 6 Amp and 16 sq. mm stud type connector (4 Nos) inside the pole at door opening for cable connection, common templates minimum for 15 poles. Detailed specifications of Galvanized Octagonal poles are given in Annexure-XX of tender document.

Providing PVC insulated and sheathed, single core, multi-stranded, Aluminium conductor cable, 10.0 sq. mm - The price shall cover for 46 supply and laying of single core, PVC insulated, stranded, Aluminium conductor of 10 sq. mm cross sectional area conforming to IS 1554 - Part-1. The cable shall be flame retardant, should not support combustion and shall be self-extinguishing and shall be of Johnson/Neo-cab/Nicco/Finolex/R.R. Kabel/Asian/Ecotek/L&T/Havells/Polycab/Avocab make.

Providing G.I. Earth Wire, 8 SWG in PVC sleeve along with cable - The price shall cover for supply and laying of soft G.I. wire of 8 SWG covered with black coloured PVC sleeve of superior quality and laid along with PVC LTUG cable properly fixed and connecting earthing terminals of each panel.

Providing GI earthing strip, 25 x 4 mm with PVC sleeve - The price shall cover for supply and laying of G.I. earthing strip of 25 x 4 mm size covered with black coloured PVC sleeve of super quality from earth pit to control/distribution panel board. The earthing strip when laid on wall, shall be fixed by means of suitable size of GI clamps and screws.

Providing maintenance free earthing - The price shall cover for providing maintenance free earthing as per the following specifications - 1. High tensile-low carbon steel rod having diameter not less than 17 mm complying with requirements of BS 4360 Grade 43A or EN10025:2-004 S275JR, molecularly bonded by 99.99% pure high conductivity copper on outer surface with copper coating thickness of 250 micron or more, Length 3000 mm (minimum). Certificates from NABL approved labs shall be submitted with test results. 2. Copper earth bus-bar of size 250 mm x 50 mm x 6 mm having electrical conductivity of 101% IACS, minimum 99.9% copper content shall be exothermically welded to rod with 4 holes of 12 mm diameter (two on each side) for connecting earthing conductor. 3. Earth Enhancement compound should have characteristics as mentioned in the RDSO specifications. It should have low resistivity preferably below 0.2 Ohm-meter, supplied in sealed bags (minimum 75 kg per pit for 5' x 5' x 10' size pit and minimum 50 kg per pit for 300 mm bore type pit. The bags shall be marked with manufacturer's name or trade name, quality, Batch No. and date of manufacture. Certificates from NABL approved labs shall be submitted with test results, for at least following parameters - i) Composition of Earth Enhancement compound ii) Resistivity - < 2 Ohm-meter iii) pH value - > 7 but < 9 iv) Moisture retaining capacity - > 10% at 105 degrees Celsius v) Water solubility - < 5% 4. Backfill 49 material - Good quality soil or excavated soil free from sand, gravel and stones shall be used for backfilling. 5. Earth pit of size 5 feet x 5 feet x 10 feet or min 300 mm bore up to 10 feet using earth auger shall be made. 6. Inspection chamber - A concrete box of 300 x 300 x 300 mm (inside dimensions) and 50 mm thickness of wall, with smooth cement plaster finish shall be provided on the top of the pit. A concrete lid, painted black, approximately 50 mm thick with pulling hooks shall be provided to cover the earth pit. PVC sleeve shall be provided in concrete wall to take out earthing connections. 7. On backside of the cover, date of the testing and average resistance value shall be written with yellow paint on black background. 8. Instead of copper bus- bar and strips mentioned in the drawing, a GI main bus-bar of minimum size 300 mm x 75 mm x 8 mm to be installed on nearby wall etc. It shall be connected to earthing with two GI strips of 50 mm x 6 mm size each, up to a distance of 10 meters from earth bus-bar (minimum 3 meters x 2 Nos GI strips to be supplied). 9. Earthing shall generally be carried out in accordance with the requirement of I.E. Rules, 1956, as amended from time to time and shall confirm to IS: 3043 of 1987 with latest amendment. 10. The earth value shall be measured and recorded at the site by painting on earth pit or nearest wall along with date of testing. It shall be less than 2 Ohms and neutral to earth voltage shall be less than 3 Volt. 11. Earthing performance after a year of installation shall be jointly checked and measured. It should be less than 2 Ohm. 12. General arrangement of the earth system shall is given in Annexure-XX of tender document.

Removal of unused existing rail poles complete with overhead line spans and other accessories and shifting the released materials to 51 stores depot - The price shall cover for removal of existing rail/tubular poles complete with structure, overhead line spans and other accessories by digging pole from base with required tools, tackles and manpower in a safe and secure manner. The dismantled rail/round poles, cross-arms, insulators,

Providing four-feet long, 18/20-Watt LED fitting complete with all accessory and LED tube - The price shall cover for supply of 1 x 18/20- Watt LED batten fitting. The fixture shall be of CRCA channel finished with white polyester powder coating with high UV and corrosion resistance. The fixture shall be equipped with end caps, push fit type lamp holders and mains connector to directly fix 4 feet long LED tube. The LED lamp shall be of 1 18/20 Watt as per Western Railways' specification no. WR/CCG/Specification/P/001 (Rev. 01) - 2018. The tube shall be of polycarbonate material. The entire fixture shall be of reputed quality and make. The price shall also cover for fixing testing and commissioning of the complete fitting at site by means of bracket made from GI flat of 25 x 3 mm with nuts, bolts and washers or on heavy duty, ISI marked PVC square box as per site requirement. Connection shall be given by means of 24/0.2 mm three-core flexible copper wire through connector and heavy-duty flexible PVC conduit. Removal of existing fittings along with brackets and handing over the same to the site in-charge is included in the scope of work.

Providing LED batten fitting, 2 x 18/20 Watt, IP 65 protection, complete with four-feet LED tubes - The price shall cover for supply of 36/38 Watt LED weather proof fitting with IP: 65 protection as per Western Railways' specification no. WR/CCG/Specification/P/001 (Rev-01) - 2018. The housing 2 and cover of the fitting shall be made from virgin polycarbonate. The fitting shall be of reputed quality and make. The price shall also cover for fixing testing and commissioning of the complete fitting at site by means of bracket made from GI flat of 25 x 3 mm with nuts, bolts and washers or on heavy duty, ISI marked PVC square box as per site requirement. Connection shall be given by means of 24/0.2 mm three-core flexible copper wire through connector and heavy-duty flexible PVC conduit. Removal of existing fittings, if any, along with brackets and handing over the same to the site in-charge is included in the scope of work.

Providing LED Street light fitting, 35-45 Watt complete with all accessories - The price shall cover for supply of 35 to 45-Watt (±10%) LED Street Light fitting made from pressure die-cast LM6/ADC12/LM24 housing with optimal heat sink for better thermal dissipation and toughened glass or UV stabilized polycarbonate cover with high transmission index for superior light output. The fitting shall be as per Western Railways' specification no. WR/CCG/Specification/P/001 (Rev-01)-2018 of reputed quality and make. The fitting shall be designed for IP: 65 class protection for pole/bracket 3 mounting. The fitting shall be provided with special moisture proof vent. The fitting shall be of reputed quality and make. The price shall also cover for fixing, testing and commissioning of the above street light fitting on pole/truss/roof/wall by fabrication and supply of 'B' class G.I. pipe of required length, diameter and shape and fixed with M.S. clamps made from M.S. flat of 40 x 5 mm size duly painted with nut, bolts and washers of 12 mm diameter. The connection shall be carried out through ISI marked, PVC insulated, flexible three-core copper wire of size 24/0.20 mm from the existing overhead line/catenary/junction box as per site conditions. The connection cord shall be protected by suitable size of heavy-duty flexible PVC conduit. Removal of existing fittings along with pipe and clamps and handing over the same to the site in-charge is included in the scope of work.

Supply, fixing, testing and commissioning of 70 Watt LED Street light fitting - The price shall cover for supply of energy efficient LED Area light/flood light luminary of 70 Watt capacity with luminous efficacy of 120 lumen/Watt. The luminary shall be made from pressure die cast aluminium housing, toughened front glass cover, fitted with secondary optics, heat sink and integrated electronic driver for long life with IP: 66 protection suitable for working on 240 Volt, 50 Hz AC supply as per Western Railways' Specification No. WR/CCG/Specification/P/001 (Rev. 01) - 2018 or latest. The fitting shall be of reputed quality and make. The fitting shall be supplied with required length of three-core flexible copper wire of 24/0.20 mm and shall be 4 fixed at site by means of suitable size of GI pipe and GI Clamps as decided by site engineer. Removal of existing fittings and handing over the same to the site engineer at his store is included in the scope of work. The price shall also cover for fixing, testing and commissioning of the above street light fitting on pole/truss/roof/wall by fabrication and supply of 'B' class G.I. pipe of required length, diameter and shape and fixed with M.S. clamps made from M.S. flat of 40 x 5 mm size duly painted with nut, bolts and washers of 12 mm diameter. The connection shall be carried out through ISI marked, PVC insulated, flexible three-core copper wire of size 24/0.20 mm from the existing overhead line/catenary/junction box as per site conditions. The connection cord shall be protected by suitable size of heavy-duty flexible PVC conduit. Removal of existing fittings along with pipe and clamps and handing over the same to the site in-charge is included in the scope of work.

Supply, installation, testing and commissioning of Extruded Aluminium Linear LED luminary, IP 54/65 protection - The price shall cover for supply, installation, testing and commissioning of Extruded Aluminum Linear LED luminary, IP 54/65 as per site condition (in case of indoor installation the fitting shall be IP 54 and in case of outdoor installation the fitting shall be IP 65) to be decided by railways. Depth of the luminaire (without driver) 5 should not be greater than 35 mm. The housing shall be constructed of extruded aluminum. System lumen output of 4000 lumens @ 6500 deg K, CCTand CRI - >80. The luminary shall be supplied with LED Driver with operating voltage 140 to 270 Volt AC, iTHD - <10%, P.F. - >0.95 and inbuilt 4 KV protection inside the driver. The luminary should conform to Western Railways' Specification No. WR/CCG/Specification/P/001 (Rev. 01) - 2018 or latest. The fitting shall be of reputed quality and make. The fitting shall be fixed at site by means of suitable size of GI Clamps/PVC block as decided by site engineer. The connection shall be given by means of 24/0.2 mm three-core flexible copper wire through proper connector as per site requirement. The fitting arrangement shall be as per the aesthetics of the room. Removal of existing fittings and handing over the same to the site engineer at his store is included in the scope of work.

Providing LED profile light as per technical specification - The price shall cover for supply, installation, testing and commissioning of IP20 based LED Strip Light with highly efficient LED, Environment friendly without no UV and IR radiation, with High Operating temperature of - 20°C to 50°C. 6 Average life L70B50 - 35,000 burning hours. Powered by an independent, isolated, SELV output, IP20 electronic LED driver. (SMPS based constant voltage supply) with Output Short-circuit protection, Surge Voltage protection and other safety test as per IS: 15885 (Part 2/Sec 13). The connection shall be given by means of 24/0.2 mm three-core flexible copper wire through proper connector as per site requirement. The fitting arrangement shall be as per the aesthetics of the room.