Military Engineer Services Tender

Material and labour for repair to potholes not exceeding 1.00 sqm each including sweeping free from dust and mud or water, scoring sunken surface in roads cutting around edges to at least 25mm in depth by applying tack coat @ 5 kg per 10 sqm, putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 Kg per Sqm, binded with 0.09 cum of stone chippings, 6.3mm size and again well rammed (including supply of premixed macadam, binder and chippings) depth of pot holes not exceeding 30mm. Complete all as specified and as directed.

Scarifying or picking gravelled, macadam or bituminous macadam surfaces exceeding 50mm deep and area not exceeding 100mm deep. Area not exceeding 400 Sqm complete all as specified and as directed.

Material and labour for preparation of existing unsurfaced water bound macadam by brushing with wire brushes for removing caked mud, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dust and dirt and applying evenly one priming/ tack coat with bituminous primer over unsurfaced water bound macadam (using paving bitumen having grade of VG-10) @ 10 Kg per 10 Sqm complete all as specified and as directed.

Material and labour for bituminous premix macadam not exceedign 75mm consolidated/ compacted thickness using Hot Mix Plant & Mechanical Paver with 4% binder (paving grade bitumen any penetration) content by weight of total mix, rolled and compacted to required camber and gradient complete all as specified and as directed.

Supply and fixing of cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of Model No DA 972.0 fixed with and including mild steel stud of suitable size as per manufacturers instructions complete all as specified and as directed.

Supply and fixing of solar cat eye aluminium alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4 V/ 0.3 Watt one NI-ed rechargeable battery (1.2 V/ 1600 MA) consisting of six super bright LED with 10,000 to 18,000 mcd completed as per manufacturers instructions complete all as specified and as directed.

Supply and fixing of metal tubular delineator made out of ABS round body fitted with 2 Nos 65mm dia highly reflective reflectors made out of PMMA and mounted on 45/ 50mm dia mild steel pipe of 600mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150 x 150 x 300mm) type B1 complete all as specified and directed.

Manufacturing, supplying and fixing retro reflective regulatory sign board of size 900mm dia meter made out of 2mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro reflective sheeting as approved by Engineer-in-charge. Letter, symbols, borders will be as per IRC-67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to mild steel frame of angle iron of size 40mm x 40mm x 4mm. The boards will be fixed to 1 No. 50mm x 50mm square post made of mild steel angle 50mm x 50mm x 4mm, 4 metre long welded to the frame with adequate anti-theft arrangement. Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as specified and as directed.

Manufacturing, supplying and fixing retro reflective Mandatory/ Regulatory sign boards of 900mm dia metre with support length of 3750mm and made up of 2mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to Type-IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders as per IRC:67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to Class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm centre to centre to back support frame of mild steel angle iron of size 25mm x 25mm x 3mm alongwith theft resistant measures, mounted and fixed with 2 Numbers. Mild steel angles of size 35mm x 35mm x 5mm to a vertical post made upto mild steel. Tee Section ISMT 50mm x 50mm x 6mm welded with base plate of size 100mm x 100mm x 5mm at the bottom end and including making holes in pipes, angles flats, providing & fixing mild steel message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical mild steel -Tee support to be painted in black and white colours). Back side of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts. Complete as per drawing, specification and direction of Engineer-in-Charge.

Manufacturing, supplying and fixing retro reflective Cautionary/ warning sign boards of equilateral triangular shape having each side of 900mm with support length of 3650mm and made up of 2mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type-IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders as per IRC:67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to Class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm centre to centre to back support frame of Mild Steel angle iron of size 25mm x 25mm x 3mm alongwith theft resistant measures, mounted and fixed with 2 Numbers. Mild Steel angles of size 35mm x 35mm x 5mm to a vertical post made upto Mild Steel Tee section ISMT 50mm x 50mm x 6mm welded with base plate of size 100mm x 100mm x 5mm at the bottom end and including making holes in pipes, angles flats, providing & fixing Mild Steel message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical Mild Steel-Tee support to be painted in black and white colours). Back side of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts complete as per drawing, specification and direction of Engineer-in-Charge.

Demolition of cement concrete of any description and in any position (unreinforced) in ground floors/ pavings not exceeding 15 cm thickness (below or above ground level) and disposing off rubbish off the premises of contonment complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, dados laid, bedded and pointed in any mortar and removal of rubbish off the site complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Material and labour for chequered cement concrete coloured tiles of size 20 cm x 20 cm x 25mm thick, set, jointed and pointed in neat cement slurry (with gray cement and pigment) and including 15mm thick in cement plaster in CM (1:6) for fixing tiles complete all as specified and as directed

Material and labour for 25mm thick cement concrete type B-0, 1:2:4 (12.5mm graded stone aggregate) as in padding to receive chequered tiling and all other similar works complete all as specified and as directed.

Material and labour for 100mm thick PCC 1:3:6 type C-2 (40mm graded stone aggregate) as in sub base and all other similar works complete all as specified and as directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and as directed.

Preparation of new or previously untreated surfaces of concrete and concrete based materials of any description and in any position over 10 cm width or girth and material and labour for applying two coat of synthetic enamel paint on concrete surfaces over one coat of priming paint plaster complete all as specified and as directed.

Dismantling of old/ unserviceable/ damaged road furniture items like cat eye, solar cat eye and delineator of any description complete all as specified and as directed.

Dismantling of old/ unserviceable/ damaged sign boards of any description inclusive of mild steel post complete all as specified and as directed.