Military Engineer Services Tender

Supply and laying 50 mm outer dia HDPE pipe (DWC) Double wall corrugated outer surface and smooth inner wall, ISI marked and as per IS : 16205 (part-24) or latest IS 14930 (part-II), 450N compressive strength with snap fit coupler with rubber ring for underground electrical cable protection conduits Orange colour complete all as specified and directed.

Supply and laying 63 mm outer dia HDPE pipe (DWC) Double wall corrugated outer surface and smooth inner wall, ISI marked and as per IS : 16205 (part-24) or latest IS 14930 (part-II), 450N compressive strength with snap fit coupler with rubber ring for underground electrical cable protection conduits Orange colour complete all as specified and directed.

Supply and laying 90 mm outer dia HDPE pipe (DWC) Double wall corrugated outer surface and smooth inner wall, ISI marked and as per IS : 16205 (part-24) or latest IS 14930 (part-II), 450N compressive strength with snap fit coupler with rubber ring for underground electrical cable protection conduits orange colour complete all as specified and directed.

Supply and lay burnt brick sub class 'B' old size in trenches abouting each other width equal to length of brick etc complete all as specified and directed.

M & L for Reinforced cement concrete (with using 6 & 8 mm TMT bar) 1:2:4 type B1 ( 20 mm graded aggregate) as in cable route indicator pillars size not less than 0.3 x 0.1 x0.75 mtr including use and waste of necessary formwork etc. including double coat of yellow colour synthetic enamel paint all over cable route indicator pillars and writting in black colour cable size as per approved pattern and grouting pillars in soil complete all as specified and directed.

Supply and laying in replacement XLPE insulated PVC inner sheathed, armoured with galvanized steel of wire heavy duty under ground cable with aluminium stranded conductor 1100 volt grade laid up trenches/duct crossing through pipe/duct or fixed on pole and with suitable size of cable gland, aluminium lugs and testing cable complete all as specified and directed by Engr-in-Charge for the following size :- 4 core 16 Sqmm

All as per item No 9 here in before but 4 core 25 Sqmm

All as per item No 9 here in before but 3.5 core 35 Sqmm

All as per item No 9 here in before but 3.5 Core 50 Sqmm

All as per item No 9 here in before but 3.5 Core 70 Sqmm

All as per item No 9 here in before but 3.5 Core 95 Sqmm

All as per item No 9 here in before but 3.5 Core 240 Sqmm

Demolition for hard standing / Bituminous road and paving complete all as specified and directed.

M & L for Boring of holes under road, pavement, hard standing by Mannualy or necessary machine for inserting of pipe up to 100 mm dia complete all as specified and directed.

S & F in replacement pipe galvanized, “Light grade”, 40mm dia. for protection of cable under road, pavment including fittings complete all as specified and directed.

M & L for surface excavation n.exc 30 cm deep and average 15 cm deep and getting out in soft loose soil complete all as specified and directed.

M & L for brocken stone or boulders hardcore of gauge not exc 63 mm deposite spread and levelled in layers not exc 15 cm thick, watered and rammed to a surface complete all as specified and directed.

M & L for 75 mm thick cement concrete type D-2 1:2:8 (40 mm graded aggregate) as in floor finishes and pavings complete all as specified and directed.

M & L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M & L for 60mm machine pressed precast concrete interlocking paver block with grey cement and pigment andy shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade complete all as specified and directed.

M & L for providing and laying at ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curved, joined with cement mortor 1:3 (1 cement coarse sand) including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm) including making drainage opening wherever required complete all as specified and directed.

Supply and fix in repairs MCCBs 4 pole 100 Amps 16 KA adjustable type with sheet metal enclosure complete all as specified and directed.

Supply and installed CPRI approved factory made, cubicle compartmentalised outdoor type LT Panel feeer pillar box, front and rear opening with locking arrangement, dust and vermin proof, fabricated out of 3.15 mm thick CRCA sheet with canopy and base frame & mild steel angle iron stand, over all finished with epoxy powder coating, suitable for operation on 415 Volts, 50 Hz, AC supply, including earthing stud, feeder labeling, danger plates etc. and feeder pillar box grouting in suitable size PCC foundation, and connection the existing LT UG cable or new LT UG cable with new cable lugs, gland complete all as specified and directed by EIC including taking out old LT panel. (Main receiving Panel near CPSS Bldg) The new LT panel comprising of the following switchgear & controls :- Incoming (a) On load change over switch 4 pole 400 Amps 415 V - 01 No (b) MCCB, 4 pole 400 Amp, 35 KA with thermal magnetic release adjustable setting - 01 No (c) Aluminium Bus bar TPN 600 Amps (d ) LED dispay 3 line Multimeter class 0.5 with suitable size CT ratio (e) LED RYB Phase indicater - 01 Set

Out going (a) MCCB, 4 pole 200 Amp, 25 KA with thermal magnetic release adjustable setting - 01 No (b) MCCB, 4 pole 160 Amp, 25 KA with thermal magnetic release adjustable setting - 03 Nos (c) MCCB, 4 pole 100 Amp, 25 KA with thermal magnetic release adjustable setting - 02 No (d) MCCB, 4 pole 63 Amp, 25 KA with thermal magnetic release adjustable setting - 02 No (e) MCB SPN, 20 Amps - 02 Nos (f) LED display ammeter 0- 400 Amps , class 0.5 with suitable rating CT - 08 Nos

Supply and installed CPRI approved factory made, cubicle compartmentalised outdoor type LT Panel feeer pillar box, front and rear opening with locking arrangement, dust and vermin proof, fabricated out of 3.15 mm thick CRCA sheet with canopy and base frame & mild steel angle iron stand, over all finished with epoxy powder coating, suitable for operation on 415 Volts, 50 Hz, AC supply, Aluminum bus bar TPN 300 Amps with PVC slieves including earthing stud, feeder labeling, danger plates etc. and feeder pillar box grouting in suitable size PCC foundation, and connection the existing LT UG cable or new LT UG cable with new cable lugs, gland complete all as specified and directed by EIC including taking out old LT panel. (Offrs Mess Panel). The new LT panel comprising of the following switchgear & controls :- Incoming :- a) MCCB, 4 pole 160 Amp, 25 KA with thermal magnetic release adjustable setting - 02Nos (b) LED disoay volt meter class 0.5 - 02 Nos (c) On load change over switch 4 pole 160 Amps 415 V - 01 No

Outgoing :- (a) LED RYB Phase indicater - 01 Set (b) MCCB, 4 pole 160 Amp, 25 KA with thermal magnetic release adjustable setting - 01 No (c) MCCB, 4 pole 100 Amp, 25 KA with thermal magnetic release adjustable setting - 01 Nos (d) MCCB, 4 pole 63 Amp, 25 KA with thermal magnetic release adjustable setting - 04 Nos (e) MCB SPN, 20 Amps - 02 Nos (f) LED display ammeter 0-400 Amps, class 0.5 with suitable rating CT - 06 Nos

Supply and installed CPRI approved factory made, cubicle compartmentalised outdoor type LT Panel feeer pillar box, front and rear opening with locking arrangement, dust and vermin proof, fabricated out of 3.15 mm thick CRCA sheet with canopy and base frame & mild steel angle iron stand, over all finished with epoxy powder coating, suitable for operation on 415 Volts, 50 Hz, AC supply, Aluminum bus bar TPN 300 Amps with PVC slieves including earthing stud, feeder labeling, danger plates etc. and feeder pillar box grouting in suitable size PCC foundation, and connection the existing LT UG cable or new LT UG cable with new cable lugs, gland complete all as specified and directed by EIC including taking out old LT panel. (MT area). The new LT panel comprising of the following switchgear & controls :- Incoming :- a) MCCB, 4 pole 125 Amp, 25 KA with thermal magnetic release adjustable setting - 02 Nos (b) LED display volt meter class 0.5 - 02 Nos (c) On load change over switch 4 pole 125 Amps 415 V - 01 No Outgoing :- (a) LED RYB Phase indicater - 01 Set (b) MCCB, 4 pole 63 Amp, 25 KA with thermal magnetic release adjustable setting - 06 No (e) MCB SPN, 20 Amps - 02 Nos (f) LED display 3 line Multimeter 0-300 Amps, class 0.5 with suitable rating CT - 01 nos

Supply and installed CPRI approved factory made, cubicle compartmentalised outdoor type LT Panel feeer pillar box, front and rear opening with locking arrangement, dust and vermin proof, fabricated out of 3.15 mm thick CRCA sheet with canopy and base frame & mild steel angle iron stand, over all finished with epoxy powder coating, suitable for operation on 415 Volts, 50 Hz, AC supply, Aluminum bus bar TPN 300 Amps with PVC slieves including earthing stud, feeder labeling, danger plates etc. and feeder pillar box grouting in suitable size PCC foundation, and connection the existing LT UG cable or new LT UG cable with new cable lugs, gland complete all as specified and directed by EIC including taking out old LT panel. (Power House Panel) Incoming :- a) MCCB, 4 pole 125 Amp, 25 KA with thermal magnetic release adjustable setting - 01 Nos (b) LED display 3 line Multimeter 0- 300 Amps , class 0.5 with suitable rating CT -01 nos (c) LED RYB Phase indicater - 01 Set Outgoing :- (a) MCCB, 4 pole 63 Amp, 25 KA with thermal magnetic release adjustable setting - 02 No (b) MCB SPN, 20 Amps - 02 Nos (c) MCB TPN, 32 Amps - 02 Nos

Supply and installed CPRI approved factory made, cubicle compartmentalised outdoor type LT Panel feeer pillar box, front and rear opening with locking arrangement, dust and vermin proof, fabricated out of 3.15 mm thick CRCA sheet with canopy and base frame & mild steel angle iron stand, over all finished with epoxy powder coating, suitable for operation on 415 Volts, 50 Hz, AC supply, Aluminum bus bar TPN 500 Amps with PVC slieves including earthing stud, feeder labeling, danger plates etc. and feeder pillar box grouting in suitable size PCC foundation, and connection the existing LT UG cable or new LT UG cable with new cable lugs, gland complete all as specified and directed by EIC including taking out old LT panel. ( Near 750 KVA Transformer). The new LT panel comprising of the following switchgear & controls :- Incoming a) MCCB, 4 pole 320 Amp, 35 KA with thermal magnetic release adjustable setting - 02Nos (b) LED display volt meter class 0.5 - 02 Nos Outgoing :- (a) LED RYB Phase indicater - 01 Set b) LED display Amper meter 0- 300 Amps , class 0.5 with suitable rating CT -01 nos (c) On load change over switch 4 pole 320 Amps 415 V - 01 No

Supply, install, testing and commissioning of AMF Panel Cubical body outdoor type , dust and vermin proof made up of CRCA sheet 3 mm outdoor type confirming to IP 53 with front and rear opening with louvers and mounted on floor with brick/PCC pedestal pillers with a clearance of atleast 0.3 m above ground level with following accessories :- (i) 320A 4P 36KA 4P thermal adjustablee MCCB with Spreader (ii) 325A 4P power contactor with 22V AC coil (iii) Mechanical interlock for power contactor (iv) LED type indicating lamp - 240V AC (v) 6A 1P 10KA C - curve control MCB (vi) Digital 3 phase voltmeter for EB & DG (vii) Dgital multifunction meter for DG (viii) 320/5, CL 1, 10VA Current Transformer . AMF LOGIC (i) 415V line voltage monitoring relay (ii) 6A 1P 10 KA C-curve control MCB (iii) Auxiliary contactor - 230V AC (iv) Auxiliary contactor - 24V DC (v) On delay timer - 230V AC (vi) 5A 2P 24V DC plug in relay (vii) Auto/manual selector switch (viii) Battery charger selector switch (ix) LED type indicating lamp - 240V AC (x) Push button (xi) DC combined Volts & Ammeter (xii) 24V 10A Battery charger

(xiii) 24V DC Hooter (xiv) Terminal block (xv) 320A TPN Aluminium busbar (xvi) Microprocessor based automatic ON if main failure logic including wiring (xvii) By pass arrangement of main supply when AMF circuit fail due to fault with provn suitable rating changer over and switches (xviii) Over load relay for Gen set. Note : Rate shall be included for ser item No 26 to 31 above for the following :- 1. Earthwork and PCC for foundation. 2. Cable shall be removed from trenches and diverted to new panel for retermination.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to GI strip 25 x 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15 mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as specified and directed by Engineer-in-Charge.

Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm complete all as specified and directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to galvanized iron earth strip 32 x 6 mm (main earthing lead) by means of galvanized bolts, nuts and washers all as per shown in electrical plate No. 5 of MES Schedule Part-I with connected to earth test point main switch board with including necessary earth work and Pre- cast RCC earth pit with cover and including dismantling/taking out of old unserviceable earthing of any position complete all as specified and directed.

S & F in replacement MCCB 100 Amps 4 pole with sheet metal enclosures box complete all as specified and directed.

Disconnecting existing LT cable from existing LT panel and stretching / opening cable to suitable required length from available rings with excavation of soil and reconnecting cable in position properly with providing new lugs, gland etc to new LT panel complete all as specified and directed.

Supply and installed CPRI approved factory made, cubicle compartmentalised outdoor type LT Panel feeer pillar box, front and rear opening with locking arrangement, dust and vermin proof, fabricated out of 3.15 mm thick CRCA sheet with canopy and base frame & mild steel angle iron stand, over all finished with epoxy powder coating, suitable for operation on 415 Volts, 50 Hz, AC supply, including earthing stud, feeder labeling, danger plates etc. and feeder pillar box grouting in suitable size PCC foundation, and connection the existing LT UG cable or new LT UG cable with new cable lugs, gland complete all as specified and directed by EIC including taking out old LT panel. (500 KVA TFR LT panel ) The new LT panel comprising aluminium main busbar of suitable shape, size for 3 phase and neutral not less than 1200 Amps rating and including the following switchgear & controls :- Incoming:- (a) ACB 4 Pole, 415 V, with Thermal Magnetic Release with LED indication display , ground fault trip , over & under voltage trip function(Manual Drawout type) circuitbreaker of capacity 800 Amps ICS - 50 KA (b) Three phase LED display Multimeter class 0.5 with suitable ratio CT - one set (c) RYB Phase indicator lamp LED Type - one set

Out going (a) MCCB 4 pole, 415V with thermal - magnetic release adjustable setting of Capacity 320-400 Amps with ruputring capacity 35 kA (b) MCCB 4 pole, 415V with thermal - magnetic release adjustable setting of Capacity 125-160 Amps with ruputring capacity 25 kA - 02 Nos (c) MCCB 4 pole, 415V with thermal magnetic release adjustable setting of Capacity 100-125 Amps with ruputring capacity 25 kA - 02 Nos (d) MCCB 4 pole, 415V with thermal magnetic release adjustable setting of Capacity 80-100 Amps with ruputring capacity 25 kA - 02 Nos (e) MCCB 4 pole, 415V with thermal magnetic release adjustable setting of Capacity 50-63 Amps with ruputring capacity 25 kA - 02 Nos (f) MCB TPN, 32 Amps - 02 No (g) MCB SPN, 20 Amps - 02 No (h) LED display ammeter 0-400 Amps, class 0.5 with suitable rating CT - 09 Nos

Supply and installed CPRI approved factory made, cubicle compartmentalised outdoor type LT Panel feeer pillar box, front and rear opening with locking arrangement, dust and vermin proof, fabricated out of 3.15 mm thick CRCA sheet with canopy and base frame & mild steel angle iron stand, over all finished with epoxy powder coating, suitable for operation on 415 Volts, 50 Hz, AC supply, including earthing stud, feeder labeling, danger plates etc. and feeder pillar box grouting in suitable size PCC foundation, and connection the existing LT UG cable or new LT UG cable with new cable lugs, gland complete all as specified and directed by EIC including taking out old LT panel. (GT complex & SNCOs Mess LT panel) The new LT panel comprising of the following switch gear & controls Incoming :- (a) Bus bar chamber having Main aluminium Bus bar for 3 phase and neutral not less than 300 A Capacity. (b) MCCB 4 pole, 415V with thermal magnetic release adjustable setting of Capacity 125-160 Amps with ruputring capacity 25 kA 01 No (c ) LED dispay 3 line Multimeter class 0.5 with suitable size CT ratio (d) LED RYB Phase indicater - 01 Set

Out going :- (a) MCCB 4 pole, 415V with thermal magnetic release adjustable setting of Capacity 80-100 Amps with ruputring capacity 25 kA - 02 Nos (b) MCCB 4 pole, 415V with thermal magnetic release adjustable setting of Capacity 50-63 Amps with ruputring capacity 25 kA - 03 Nos (c) MCB TPN 32 Amps - 02 Nos (d) MCB SPN, 20 Amps - 02 Nos

Supply and installed CPRI approved factory made, cubicle compartmentalised outdoor type LT Panel feeer pillar box, front and rear opening with locking arrangement, dust and vermin proof, fabricated out of 3.15 mm thick CRCA sheet with canopy and base frame & mild steel angle iron stand, over all finished with epoxy powder coating, suitable for operation on 415 Volts, 50 Hz, AC supply, including earthing stud, feeder labeling, danger plates etc. and feeder pillar box grouting in suitable size PCC foundation, and connection the existing LT UG cable or new LT UG cable with new cable lugs, gland complete all as specified and directed by EIC including taking out old LT panel. (Candidate living LT panel ) The new LT panel comprising of the following switchgear & controls Incoming (a) Bus bar chamber having Main aluminium Bus bar for 3 phase and neutral not less than 300 Amps Capacity. (b) MCCB 4 pole, 415V with thermal magnetic release adjustable setting of Capacity 125-160 Amps with ruputring capacity 25 kA 01 No (c ) LED dispay 3 line Multimeter class 0.5 with suitable size CT ratio (d) LED RYB Phase indicater - 01 Set

Out going (a) MCCB 4 pole, 415V with thermal magnetic release adjustable setting of Capacity 50-63 Amps with ruputring capacity 25 kA - 04 Nos (b) MCB TPN 32 Amps - 02 Nos (c) MCB SPN, 20 Amps - 02 Nos

Supply and installed CPRI approved factory made compartmentalised outdoor type AMF panel with LT feeder pillar panel, front and rear opening with locking arrangement, dust and vermin proof, fabricated made of 3.15 mm thick CRCA sheet with canopy, mild steel angle iron stand, over all finished with epoxy powder coating, suitable for operation on 415 Volts, 50 Hz, AC supply, including earthing stud, feeder labeling, danger plates etc. and feeder pillar box grouting in suitable size PCC foundation, and connection the existing LT UG cable or new LT UG cable with new cable lugs, gland complete all as specified and directed by EIC including taking out old LT panel. (Pump house) (A) AMF panel portion consist of the following switch gear and controlls :- (a) MCCB 4 pole, 415V with thermal magnetic release adjustable setting of Capacity 100-125 Amps with ruputring capacity 25 kA 02 Nos (b) 4 pole power contactor of capacity 130 Amps with NO+NC (c) Three phase and neutral Aluminium bus bar of 300 AMP capacity (d) AMF panel controller for reading DG set electrical parameter and for and Auto/ manual Start/Stop facility (e) Dg set Controller power supply ON/OFF and DG set Auto / Manual mode operation switch (f) Battery Charger of 12/24 volt (g) DG set emergency stop push button (h ) LED dispay 3 line Multimeter with CT (j) LED RYB Phase indicater - 01 Set

(B) LT feeder pillar panel portion consist of the following switch gear and controlls :- (a) Three phase and neutral Aluminium bus bar of 300 AMP capacity (b) MCCB 4 pole, 415V with thermal magnetic release adjustable setting of Capacity 63-80 Amps with ruputring capacity 25 kA -01 Nos (b) MCCB 4 pole, 415V with thermal magnetic release adjustable setting of Capacity 50-63 Amps with ruputring capacity 25 kA -03 Nos (c) MCB TPN, 32 Amps - 01 Nos (d) MCB SPN, 10 Amps - 01 Nos (e) LED display ammeter of 0-100 Amps , class 0.5 with suitable rating CT - 04 Nos