Military Engineer Services Tender

All as per Item No.3 above but for dummy / construction joints of size 20 to 25 mm wide and 30mm deep complete all as specified and as directed.

All as per Item No.3 above but for dummy / construction joints of size 15 to 20 mm wide and 30mm deep complete all as specified and as directed. Note for item No.1 to 5 Utmost care shall be taken during raking out existing old sealent compound. Any minor/major increase in the width and depth of existing joint shall be repaired with CM 1:3 by contractor at his own cost. The contractor shall consider this aspect while quoting his rate.

M & L in replacement for fabrication and erecting of Road sign Board of size 1200mm x 1200 mm (size of aluminium composite panel) errect in position as directed adopting the following specification / measurement. (a) Main Post 02 Nos of stainless steel pipe 50 mm dia & 1.5 mm wall thickness of grade 316, lenght of each post 2.10 mtr( 1.8 mtr above GL and 0.30 mtr below GL) (b) Frame around aluminium sheet , fabrication with 25 mm size stainless steel square tube with 1.5 mm wall thickness including fixing arrangement for aluminium sheet and welded on main post. (c) 3 mm thick aluminium composite panel material of 2 mm thick mineral core sandwiched between two aluminium sheets (each 0.5 mm thick). The aluminium composite panel shall be coil coated, with kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on exposed face and polymer (service) coating on other face, fixed over SS frame.

(d) Providing both side of aluminium sheet High intensity face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01and 2mm thick tranparent acrylic sheet fixed with screw over sticker complete. (e) Including exacavting 25cmx25cmx60cm post hole in any strata and filling the same with PCC 1:2:4 type B2. (Note; Stainless steel section mentioned above shall be of grade 316.)

All as per item No 6 above but size of board 900 mm x 600mm

S&F in repair road safety convex mirror made up of polycarbonate reflective with hood for road turning, intersection, curves, ‘T’ junction, etc, unbreakable & strong, mounted on and body made of ABS / Fiber / Plastic of size 100 cm dia fixed over & including 80 mm bore MS pipe of 2.4 Metre length duly powder coated, fixed with adjustable clamp, pole fixed in plain cement concrete 1:2:4 Type B1 (using 20mm graded crushed stone aggregate) block of size 450x450x450mm deep including necessary, excavation & earthwork along with taking out of old safety convex mirror, complete all as specified and as directed. Notes : (i) A mild steel base plate of size 250mm x 250mm x 3mm shall be welded at bottom of pole. (ii) All steel & iron surfaces other than powder coated shall be painted with two coats of synthetic enamel paint of approved tint over a coat of red oxide zinc chrome primer.

M&L for Providing and applying 2mm thick road marking paint (retro-reflective with glass bends @ 250 gms per sqm) of specified shade / colour using hot thermoplastic material by fully / semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T & P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc complete as per direction of Engineer-in-charge and accordance with applicable specifications.

S&F in repairs Speed bumps of size 750mmx250mmx75mm made of sturdy plastic high resistance to severe impact and harsh weather conditions with dovetail interlocking type sub units made to bind prefectly into one firm bump having pre-coloured material (black/yellow) and UV stablizers to keep them prepetually colourful studded with with reflectors on either side fixed on road surface with & including nails / screws / bolts / polymer / epoxy adhesive etc all as per manufacturer’s instructions including filling up hollow portion of bumps with & including PCC 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) complete all as specified and as directed including dismantling and taking out old unserviceable / broken speed bumps of any type . Make:- 3M / TATA / ‘DARK EYE.

Supply and fixing cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA strip lens reflector of model No. DA 972.0 or eq model of make specified fixed with and incl MS stud of suitable size as per manufactures instructions complete all as specified and as directed.

Demolition of cement Concrete/PQC in ground floors and pavings any thickness (below or above ground level) and removing the debries upto 1.5 km complete all as specified and as directed.

Supplying and laying 400 micron thick HDPE sheet (Virgin Quality) water proof, wrinkle free without puncture having minimum weight 390gm/Sqm over tack coat and cushion as specified in the design with overlap between adjacent strips and at transverse joints as minimum 300mm (No additionaI amount to be paid for overlap) complete all as specified and as directed.

M&L 10 mm thick sand cushiong with clean river sand duly clear of residual , organic and deleterious materials spread evenly to uniform thickness laid over existing sub base as specified and directed. (No additionaI amount to be paid for overlap)

M&L for 100 mm thick cement concrete 1:3:6, type C-2, (using 40 mm graded stone aggregate) as in Sub base for path/road / flooring complete all as specified and as directed.

M&L for Cement concrete work in pavement/hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less including all necessary formwork complete all as specified

M&L Finishing surface of concrete roads, pavements by brooming when the concrete is green complete all as specified and as directed.

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound of Grade 'A' complete all as specified and as directed.

M&L Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing of compound Grade 'A' complete all as specified and as directed.

M&L Forming 12mm thick Expansion joints for 150 mm thickness of concreate slab filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ complete all as specified and as directed.

M&L Forming 12mm thick Expansion joints for 250 mm thickness of concreate slab filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ complete all as specified and as directed.