Military Engineer Services Tender

PROVISION OF AIR CONDITIONER IN OPERATIONAL READINESS ROOMS AT CASU UNDER CG DHQ-3 NEW MANGALORE :- (I) Supply and installation of air cooled split air conditioner, electric driven single phase of capacity 1.5 TR , BEE 5 star rated including fitment of required copper piping as required at site, control cable, outdoor unit stand and all installation accessories complete all as specified and directed.- 02 Nos (II) Supply and installation 2 TR tower Split AC indoor/outdoor unit, single phase, 230 Volt, 50 Hz including fitment of required copper piping as required at site, control cable, outdoor unit stand and all installation accessories complete all as specified and as directed.- 01 Nos (III) Supply and fix Voltage Stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of +/- 2.5% and of capacity 5 KVA suitable for 1.5/2 TR air conditioner.- 03 Nos (IV) S & F DBOX 3 pin modular MCB Socket with 16/20 Amp SP, and including plastic enclosure as per manufacturer instruction fixed on wall surface complete all as specified and as directed Make Havells, Model DHDMCSN0251016 or equivalent-03 Nos (V) M & L for sub main wiring with 2 runs of 4 Sqmm and one run as earth continuity wire single core PVC insulated unsheathed multistranded copper conductor cable 1100 volts grade FRLS drawing in and including PVC casing capibng in wall of suitable size complete. Note one run of three single core cable and conduit shall be measured as one length-15 RM

PROVISION OF UPVC GLASS FITTING AT SINGLE OFFRS ACCN AT DHQ-3 NEW MANGLORE (a) Supply and fixing factory made uPVC white colour Two track four panels sliding glazed door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 8.00 sqm upto 10.00 sqm) comprising of uPVC multi-chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.l fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Area to be covered – 17.60 SQM (b) Supply and fixing factory made uPVC white colour Two track two panels sliding glazed door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) comprising of uPVC multi-chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC, extruded glazing beads, uPVC extruded interlock and uPVC extruded line sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Area to be covered - 9.60 SQM (c) S& F Sheet glass 4.8 mm thick, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane with and including solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers. Area to be covered - 24.48 SQM