Military Engineer Services Tender

Removing of excavated surplus soil to a distance not exc 50 m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

Removing of excavated surplus hard rock to a distance not exc 50 m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

Supplying, laying, fixing, jointing and testing LT under ground XLPE insulated, galvanised steel strip or wire armoured heavy duty electric cable with alumimium conductor, 1100 volts grade, cross sectional area 10Sqmm x 2 Core, IS 7098 marked, with electric connection lugs, laid in trenches/under floor or fixed naked with walls / on poles/ in ducts / in GI pipes etc. and including taking down complete all as specified and directed. Note - Excavation, earth work, sand cushioning, PCC cover land Gl pipe shall be measured and paid separately.

Description same as per Item No. 06.00 above but 16 sqmm x 4 Core.

Description same as per Item No. 06.00 above but 25 sqmm x4 Core.

Description same as per Item No. 06.00 above but 35 sqmm x 3.5 Core

Description same as per Item No. 06.00 above but 50 sqmm x 3.5 Core

Description same as per Item No. 06.00 above but 70 sqmm x 3.5 Core.

Description same as per Item No. 06.00 above but 95 sqmm x 3.5 Core.

Supply and Laying DWC HDPE pipe of outer dia of 40mm and inner dia 32mm polyethylene (PE) with smooth internal and profiled external surface for non-pressure for underground cable including bends complete all as specified and directed.

ditto but for outer dia of 50mm and inner dia 38mm

ditto but for outer dia of 63mm and inner dia 50mm

Supply and laying Gl pipe light grade 40 mm bore in trenches, under floors, roads, along poles for protection of cables with all necessary fittings and sealing ends complete all as specified and directed.

All as per item No 16 above but 50 mm dia

All as per item No 16 above but 80 mm dia

S&F in repair LT Pin type insulator, porcelin, vitereous (single disc assembly), white, brown or green 100 mm height and 65 mm dia, including one galvanised mild steel spindle, two galvanised iron washers and galvanised nuts suitable for working pressure of 1100 volts grade complete all as specified and directed.

S&F in repair LT shakle type insulator, porcelain, viteous white, brown or green 100 mm height and 115 mm dia section of straps 31 x 5 mm with 14 mm dia of bolt, ball and socket type with clamp suitable for the conductor of required size and working pressure 1100 volts complete all as specified and directed.

Supply and fix Loop type insulator, porcelain, vitreous, white, brown or green small size 65x90 mm, clearence of hole 16 mm all as specified.

Trimming/ lopping of tree branches touching LT/ HT OH lines not exceeding 30 cm girth, shrub, vegetation, bushwood and saplings at least upto 2 mtr from outer edge of ACSR including removing of branches of trees etc to a distance exceeeding 100 mtr and not exceeding 150 mtr complete all as specified and directed. Note :- (i) Linear length centre to centre of the poles shall only be measured. (ii) Shutdown wherever required shall be informed well in advance to Engr-in-Charge who shall make necessary arrangement.

Surface clearing by cutting shrubs, vegetation , grass, busheds, weeds and trees upto 30 cm girth, sweeping and removing the same to distance not exceeding 50m away all as specified and directed by Engr-in-charge

M&L painting of LT 09 mtrs long steel pole with cross arm and clamp of any length and shape for LT over head line with two coat of aluminium paint including preparation of existing surfaces and marking pole no. ina 15 cm dia yellow circle and marking 03 nos. black and 02 Nos. white bands/ stripS with 30 cm wide fluorescent paint from bottom of pole up to 1.5 mtr height complete all as specified and directed.

S&F in replacement of unserviceable Straight through LT joint including jointing material and excavation upto 3mtr length and make good surface after jointing of cable complete of size 16 to 50 sqmm 3.5 core complete all as specified and directed.

S&F in replacement of unserviceable Straight through LT joint including jointing material and excavation upto 3mtr length and make good surface after jointing of cable complete of size 70 to 120 sqmm 3.5 core complete all as specified and directed.

S&F MCCB 3 pole, 63 Amps, C curve, breaking capacity 16 kA, |lcs=100%lcu complete with connection, testing and commissioning including spreader link & taking down complete all as specified and directed.

S&F MCCB 3 pole, 100 Amps, C curve, breaking capacity 16 KA, lcs=100%lcu with connection testing and commissioning including spreader link & taking down complete all as specified and directed.

S&F MCCB 3 pole, 125 Amps, C curve, breaking capacity 25 kA, lcs=100%lcu with connection testing and commissioning including spreader link & taking down complete all as specified and directed.

S&F MCCB 3 pole, 160 Amps, C curve, breaking capacity 25 kA, lcs=100%lcu with connection testing and commissioning including spreader link & taking down complete all as specified and directed.

S&F MCCB 3 pole, 200 Amps, C curve, breaking capacity 36 KA, lcs=100%lcu with connection testing and commissioning including spreader link & taking down complete all as specified and directed.

S&F MCCB 4 pole, 250 Amps, C curve, breaking capacity 36 KA, lcs=100%lcu with connection testing and commissioning including spreader link & taking down complete all as specified and directed.

Supply and fixing in replacement of Aluminium conductor steel reinforced, including jumfering etc complete all as specified and directed.

Labour for Re-streaching of old ACSR conductor on LT/HT pole for 3/5 Nos of conductors of span complete all as specified and directed.

M&L in replacement of cross arms bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, dilling holes for bolts, in any shape or size and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and directed.

M&L for spraying chemical (Glycel/ roundup and chemical composition Isopropyl amine salt of glyphoate a.i - 40.60% , surfactant inert polyoxy ethylene amaine 15.00% & manufacturieng impurities 4.00%) on area to remove unwanted vegetation / grass at various locations as directed by Engr-in-Charge. Notes - 1. Labour and equipments to spray chemical on required area are inclusive in quoted rates. 2. Spray will be repeated quarterly or as per the directions of Engr-in-Charge.

M&L earthing complete with galvanised steel earth plate electrode of size 600 x 600 x6 mm thick buried directly in ground in vertical position (earth pit not less than 2.25 m deep below the normal ground level) with top edge of the earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check and washers of galvanised iron or steel, all as shown in electrical plate no. 3 of SSR Part - 1, connected to earthing test point and complete all as specified and directed. Note:- The unit rate shall also include for earth work in any |type of sol, PCC 1:3:6 type C-1 (using 20 mm grade araded crushed stone aggregate) earth chamber, RCC 1:1.5:3, type A-1 cover slab, 40 mm thick reinforced with 6 mm dia TMT bar @ 150 mm C/C both ways, 10 mm dia plain bar lifting handle embedded in cover slab, 20 mm bore medium grade Gl watering pipe, 15 mm bore GI light grade earth lead protection pipe, funnel, wire mesh, copper lugs, charcoal and common salt in alternate layer, GI strip and 15 mm dia protection pipe upto 7.5 mtr from earth plate etc complete all as specified and directed.

Description same as per Item No. 37.00 above but Aluminium strip 25 X 4 mm main earthing lead.

Description same as per Item No. 37.00 above but Galvanised strip 32X6 mm main earthing lead.

M&L for repair / servicing of LT Panel board including of locking arrangement and independent duly prewired with colour code three phases and neutral for 415 volts, 50 Hz electric supply with and including suitable sizes of lugs nut bolt washer, including indictor lamp, voltmeters and ammeters, two coats paint after a coat of primer including angle iron frame bottom of panel, including welding of panel necessary including replacement of unserviceable component. Note - Spares will be measured and paid separately as supply only items.

Supply only Indicator lamp LED type (set of three) complete all as specified and directed.

Supply only Ammeter LED type up to 400Amps as per sample complete all as specified and directed.

Supply only Voltmeter LED type up to 500Volts as per sample complete all as specified and directed.

Supply only Selector Switch suitable for Ammeter and Voltmeter complete all as specified and directed.

Supply only CT coil up to 400 Amp (set of three) complete all as specified and directed.

Supply, installation, testing and commissioning LT PANEL board outdoor type (CPRI Approved) of suitable size, Kiosk type, factory assembled, fabricated and of suitable size angle iron, channel and MS sheet 3 mm to 3.15 mm thick (inner compartment is 2.0 mm thick) double door type, front and rear openable with locking arrangement and duly prewired with colour code three phases and neutral for 415 volts, 50 Hz electric supply with and including suitable sizes of cable glands for incoming and outgoing cables cubical type duly powder coated over a coat of primer, grouting of panel 60 cm above the ground level by provisioned 90 cm long angle iron frame bottom of panel 40x40x5 mm thick , welded on all four corners , embedded in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate up to 30 cm and, grouting the panel board on and including suitable size foundation structure with the following components (Location : Near Bldg No T34, Ponda Mil Camp ):-

(a) MCCB 160 Amps 4 pole, 25 KA, 415 volts, lcs =100 % lcu, Adjustable short circuit setting type (incoming) – 01 No. (b) Digital Ammeter 0-200 Amps with CT 200/5A rating - 01 Nos (c) Digital Voltmeter 0-500 volts - 01 Set. (d) Indicating lamps R, Y & B -01 set (e) Busbar Chamber: 1 Set ( 3 L + 1 N ) Electrically grade Bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size. (f) MCCB 63 Amps 4 pole, 16 KA 415 Volts, lcs =100 % lcu, Adjustable short circuit setting type (outgoing) - 03 Nos (g) MCCB 40 Amps 4 pole, 16 KA 415 Volts, lcs =100 % lcu, Adjustable short circuit setting type (outgoing) - 02 Nos. (h) Free space for fixing spare MCB TPN/ SPN - 01 No.

Supply, installation, testing and commissioning LT PANEL board outdoor type (CPRI Approved) of suitable size, Kiosk type, factory assembled, fabricated and of suitable size angle iron, channel and MS sheet 3 mm to 3.15 mm thick (inner compartment is 2.0 mm thick) double door type, front and rear openable with locking arrangement and duly prewired with colour code three phases and neutral for 415 volts, 50 Hz electric supply with and including suitable sizes of cable glands for incoming and outgoing cables cubical type duly powder coated over a coat of primer, grouting of panel 60 cm above the ground level by provisioned 90 cm long angle iron frame bottom of panel 40x40x5 mm thick , welded on all four corners , embedded in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate up to 30 cm and, grouting the panel board on and including suitable size foundation structure with the following components (Location : EME Wksp/ ASRI, Bambolim Army Camp):-

(a) MCCB 320 Amps, 4 pole, 45 KA, 415 volts, lcs =100 % lcu, Adjustable short circuit setting type (incoming) – 01 No. (b) Digital Ammeter 0-400 Amps with CT 250/5A rating - 01 Nos (c) Digital Voltmeter 0-500 volts - 01 Set. (d) Indicating lamps R, Y & B -01 set (e) Busbar Chamber: 1 Set ( 3 L + 1 N ) Electrically grade Bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size. (f) MCCB 125 Amps 4 pole, 25 KA, 415 Volts, lcs =100 % lcu, Adjustable short circuit setting type (outgoing) - 02 Nos (g) MCCB 100 Amps 4 pole, 16 KA, 415 Volts, lcs =100 % lcu, Adjustable short circuit setting type (outgoing) - 01 Nos (h) MCCB 40 Amps 4 pole, 16 KA, 415 Volts, lcs =100 % lcu, Adjustable short circuit setting type (outgoing) - 01 Nos. (i) Free space for fixing spare MCB TPN/ SPN - 01 No.

Cutting chases, pinning in, making good of Bituminous road/ PCC hard standing to facing where required and pointing in cement mortar 1:3, exc.10 cm. but not exc.20 cm girth to ends or edges of landing,steps,cills,sunshades,shelves,lintels,etc.and cutting chases for concealed water tubing or concealed conduit wiring,laying of cables and making good with old shape and size all as specified and directed.