Military Engineer Services Tender

SCHEDULE "A" PART-IV (INTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-V (ROAD/PATH/CULVERT/HARD STANDING) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-VI (SEWAGE DISPOSAL) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-VII (AREA DRAINAGE) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-VIII (EXTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-IX (EXTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART -X (MISCELLANIOUS ITEMS) Note:- This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col.' E ' signifies this fact only.

INTERNAL WATER SUPPLY S & F concealed stop cock 15mm dia with wall flange screwed both ends for iron pipe and fixed including all necessary fittings like CPVC Tee, nipple etc complete all as specified and directed

INTERNAL ELECTRIFICATION S & F BEE energy efficient BLDC high-speed ceiling fan having 1200 mm blade sweep, air-flow not less than 210 CMM, operating voltage 220-240 V and frequency 50 Hz, including a down road of suitable size and electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fan complete all as specified and directed.

S & F energy efficient non-metallic fresh air fan having blade sweep 250 mm, air delivery not less than 860 CMH, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fresh-air fan complete all as specified and directed. Make: Havells or BAJAJ

SEAWGE DISPOSAL M&L for LLDPE Septic tank designed to carry sewage and sludge water and excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc complete for 10 user conventional complete all as specified and directed.

EXTERNAL WATER SUPPLY Cutting of existing bituminous surface/PCC hard standing by using mechanical method of any type for laying GI pipe and making good disturbed surface complete all as specified and directed.

Material and Labour for construction of brick masonary valve chamber of size 900 x 900 x 600mm (internal dimensions) with PCC foundation 1:4:8 type D2 using 40 mm graded stone aggregate, 150 mm wide offsets around over 100 mm thick hardcore, 200 mm thick fly-ash brick masonary walls built in CM 1:6, 100 mm thick PCC 1:2:4 type B1 coping finished even and smooth, rendering 10 mm thick in cement mortar (1:6) finished even and smooth, without using extra cement internally including top of floor including excavation earthwork in hard/dense soil 6 mm thick MS sheet cover fixed on 25mm x 25mm x 6mm thick angle iron frame with hold fasts embedded in PCC coping with locking arrangement, mild steel handle and painting to steel surfaces with two coats of synthetic enamel paint over one coat of primer including disposal of surplus soil to a distance not exceeding 50m etc complete all as specified and directed.

EXTERNAL ELECTRIFICATION Supplying, installation, testing and commissioning outdoor type LT panel board suitable for working on 3 phase, 4 wire, 415 volts, AC, 50Hz, cubicle type, floor mounted, free standing, dust and vermin proof, air ventilationmade out of 3.15 mm thick CRCA sheet and suitable sized angle iron and flat duly powder coated painting and shall be any CPRI approved manufacturer as approved by GE. Panel shall have front and rear opening, mechanical type locking arrangement, cable alleys, bus bar chamber and switch gear compartment, hinged door with rubber gasket, bottom cable entry holes for incoming and out going cables, earthing terminals, affix danger notice plate, aluminium bus bar TPN 60 Amps duly covered with heat shrink sleeves duly colour coaded fixed on DMC/SMC insulators, housed in a separate bus bar chamber and control wiring with copper conductor cables of adequate size and length, incoming and outgoing MCCBs shall have extended bus bar links and the panel board shall be mounted on mild steel angle iron frame of size 50x50x3mm duly painted with two coat of synthetic enamel over a red oxide primer with necessary nuts, bolts and washers etc necessary civil work/ PCC foundation as per site requirement and approved by GE complete all as specified and directed including comprising of following:- (a) MCCB 40 Amps, 4 P, 16 KA, 415 volts, 50Hz-1 No (b) MCB 32 Amps TPN, 16 KA, 415 volts, 50Hz-1 No (c) MCB SPN 20 Amps (d) Digital voltmeter, Ammeter, with CTs, VSS & ASS- 01 set (e) LED phase Indication lamps RYB-01 set