Military Engineer Services Tender

S & F Curtain rails Mild steel chromium plated with fixing brackets, stops, rollers etc.

S&F PTMT Mirror Cabinet of Size 430mm x 335mm x 140mm with all necessary arrangements for fixing to wall (Make: Water Tec / Commander/ Jasmine)

Taking down cement plaster of stone /Pcc block /brick wall / top of chajja, or concrete surface of any description including raking out joints hacking for key securing down with water etc and removalof debris to outside of INS Mandovi Area including filling of open joints in cement mortar 1:6 Complete

M & L for rendering 10 mm thick in cement mortar 1:4 on stone masonry surfaces or surface other than fair face of brickwork even & smooth with using extra cement

M&L for preparation of newly plastered surfaces preparatory to distempering, Priming plastered and other surfaces with alkali resistant priming paint, 1mm thick wall care putty & distempering walls with two coats of distemper oil emulsion, white or tinted

M&L for preparation of old plastered surfaces preparatory to distempering, Priming plastered and other surfaces with alkali resistant priming paint, 1mm thick wall care putty & distempering walls with two coats of distemper oil emulsion, white or tinted

Demolition of Brickwork or stone/bou-lder masonry, cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by engr in charge

Dismantling PCC Floor,hearth or wall tiling including cement mortar Bedding, removing serviceable tiles to stores and removing debris to a distance exc 250 m and not exc 1000 m spread and levelled

M & L For Screed Bed or Bedding Layer of mortar 15 mm thick in cement mortar 1:6 for laying Floor finishes

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M & L for rendering 15 mm thick (10mm in cement mortar 1:6 and 5mm in cement mortar1:4) on stone masonry surfaces or surface other than fair face of brickwork even & smooth with using extra cement

M&L for Preparing new plastered or unplastered surfaces of walls applying two coats of 100%Anti fungal acrylic emlusion exterior grade paint (make- asian/Berger/Nerolac/Dulux)over a coat of acrylic primer in approved shade and as per manufacture instruction including necessary scaffolding etc complete and directed by Enggineer-in-Chargre on newly plastered surfaces incl prepration of surfaces on external surfaces (wall facia cornices etc)by applying ready mix Birla whirte white cement based wall care putty (where required )over incl

M&L for complete removal of any existing treatment by scrapping/rubbing & finally washing down with water and freeing the surface from all loose dirt, chalk, grease, fungi, algae, flakes,etc and making suitable for Apex painting on external surfaces (wall facia comices etc) by applying ready mix 'Birla White' white cement based wall care putty( where required ) and applying two coat of 100% antifungous acrylic emulsion exterior grade paint (white & blue) (make Asian/Berger/Nerolac/Dulux) over a coat of acrylic primer in approved shadeand as per manufactures instruction & bio wash including necessary scaffolding etc complete and directed by Engineer-in-charge

Taking down chowkats with shutters (without taking off shutters from the frames) exc. 1.5 sq m but n exc 4 Sqm each.

Taking down chowkats with shutters (without taking off shutters from the frames) n.exc. 1.5 sq m

S&F 100mm X 63 mm size factaory made FRP door frame, frame fixed with 3 Nos on either side with MS flat iron 25 mm x 3mm cut to size and made to swhape and fixed as in hold fast after necessary taring and sanding and fixed as per manufacture instruction and as directed. Thickness of FRP lamination shall be 2 mm. Core shall be polyurethane foam/high density (more than 40 Kg per cubit meter) cellular foam done in situ. Second class wooden blocks shall be provided to hold the fittings. The size of the chowkats shall be inclusive of 2 mm thick FRP lamination. Make : Delux polytab, Advance marketing/Quality Decor/Festel Tanks Pvt Ltd/Ommega Fiber, Verma Goa as approved

S&F factory made panneled FRP door shutters, 30 mm thick with 2 mm thick FRP lamination top rail of size 25 X 150 mm, lock rail and bottom rail of size 25 X 150 mm with 12 mm thick panels of FRP sections of box type construction as per IS 4020 core shall be polyurethane foam/high density (more than 40 Kg per cubic meter) cellular foam done in situ and fixed in position as per manufacturer's instructions with and including the following fittings and as directed ( the thickness of FRP shutter and panels shall be inclusive of 2mm thick FRP lamination) Make of shutter Delux polyfab, Advance marketing/ Sal swarn/ Quality Decor/ Festel tanks Pvt Ltd/ Omega

Supplying only Integral waterproofing compound

M & L 5mm thick plastering in cement mortar 1:3 finished even & smooth, without using extra cement on ceiling

M&L for preparing new plastered surfaces of ceiling, applying 1mm thick acylic putty on ceiling and applying three coats of white wash

M&L for preparing Old plastered surfaces of ceiling, applying 1mm thick acylic putty on ceiling and applying three coats of white wash

S&F aluminum powder coated door/window/ventilator shutter including frame , any type (sliding/open-able/louver ) with frame , & other similar work etc fabricated by using the JINDAL / CENTURY section including necessary arrangement to receive 4mm thick sheet glass or wire mesh with aluminium channel beading & stainless steel screws including the cost of rubber gasket / rubber beading etc complete . But the weight of the rubber gasket / beading will not be measured with weight of aluminium shutter Note :- Sheet glass & wire mesh shall be measured & paid separately

Supply and fix aluminium powder coated grill, 7.5 mm thick

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples

S&F Sheet glass 6.3 mm, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane

Dismantling/taking down existing hessain base fell or clay tiles or any other existing water proofing treatment from roof/chajja including cement plaster, cleaning the surface and removing the dismantled ebris to a distance exceeding 1.50 km but not exe 5 km to outside the MD land and laying water proofing membranetreatment using 4mm thick APP modified membrane consisting five layer membranes withfeatures as specified, weighing not less than 4.00kg/sqm laid over a coat of cold bituminous primer @ 0.40 kg/sqm by torching the membrane and sealing the over lap by 100mm length side and 150mm width side all as per ,anufactures instruction including joints and changes in direction be curved with cement mortar 10mm thick 1:3 mixed with SBR latex @ 2.00ml/bag of cement curved well before laying of membrane, including applying two coats of solar reflective bituminous aluminium paint @ 0.10 litre/sqm all as per manufacturer instructions and to the satisfication of Eng-In-Charge: Note: (i) Irrespective of lap the net covered area will only be measured for payment.(ii) The quoted rate is deemed to be inclusive of bituminouus primer, APP membrane, Solar reflective bituminous aluminium paint & SBR latex.

M&L Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate), 25mm thick on concrete surface over top of RCC roof with using waterproofing compund as per manufacture instruction finished even & fair with using extra cement

S&F in repairs 110MM dia Rainwarer PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L 75 mm thick plain Cement concrete type c-2, 1:2:4 (using 40mm garded stone aggregate ) as in plinth protection/ foot path etc. finishinf cement concrete surface even and smooh with out using extra cement including making joints with bitumastic filling in proportion of bitumen and snad (1:2) complete all as apecified and directed by engineer in charge .

S&F Mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes Fe410-W(Gde E-250) quality-A

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground

Dismantling fencing wire mesh, any type complete all as specified and directed by engineer in charge

M&L Pcc 1:3:6 type C2 using 40mm graded stone aggregate for foundation filling and mass concrete .

S&F mild steel for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

Supply only chain link fencing with 3mm dia, Galvanished steel wire and size of mesh 75mmx 75mm all as specified/directed weight exc 2.0 kg per sqm and nexc 2.50 kg per sqm

Fixing only chain link fencing including line wires, mesh, size and type to any of strands, rails, straining bolts, etc. including provission of biniding wire

M&L Precast cement concrete solid Block masonry in PCC 1:3:6 type C1, 20mm graded trap agg exc 10cm in width and setting in CM 1:4

S&F for mild steel screw bolts ( machine made ) with hexagonal or square head at one end and screwed the other , or screwed both end , each screwed end to be fitted with washers and one hexanonal or square nut,but length of bolt exc 5cm but n exc 10cm long. Diameter of shank will be 10 mm.

M&L TMT bars 10 mm cut to length bent to shape required including cranking and binding with MS wire n less than 0.9mm dia but for stiffener of chainlink fenceing

M&L providing cement concrete type A1 Grade M20, 1:1.5:3 (using 20mm graded aggregate ) in in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases)

M&L TMT bars 10 mm dia and over cut to length bent to shape required including cranking and binding spirally for hooping columns hooking ends and binding with and including MS wire(unnealed ) n less than 0.9mm dia or securing with clips .

M&L TMT bars 5mm dia and over up to and including 10 mm dia in stirrups spaces and binders cut to length bent to shape required including cranking and binding spirally for hooping columns hooking ends and binding with and including MS wire(unnealed ) n less than 0.9mm dia or securing with clips .

M&L for formwork to sides of concrete foundations ,footings bases of columns raft and raft beams sides of sofits of foundations and plinth beam and similar work vertical or batter

M&L for formwork to sides of pillars ,posts ,struts,piers,columns and stanchions for fair finished surfaces .

M&L Rendering 10mm thick CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement

M&L Prepration of new or previously untreated steel surfaces & apply two coat of anti corrosive paint over one coat of Red oxide primer . Surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint

M&L Prepration of old or previously untreated steel surfaces & apply two coat of anti corrosive paint over one coat of Red oxide primer . Surfaces of any description, over 10 Cm in width or grith, not other wise description

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing completek conforming to Fe-290 Gde E-165

M&L Pcc 1:2:4 type B0 using 12.5mm graded stone aggregate for coping including necessary form work..

M&L Preparing new plastered or unplastered surfaces of walls and applying three coats of white wash complete.