Tenders of National Institute Of Standards And Technology Usa

Gaithersburg Pop-up Food Services

Background nist Is Seeking Information From Sources That May Be Capable Of Providing A Commercial Item Solution That Meets Or Exceeds The Following Draft Minimum Specifications. The Required Item Is A Superconducting Magnet With A Room Temperature Bore, Which Will Be Used In Our Laboratory, That Produces A Sufficiently Large Magnetic Field To Saturate High Perpendicular Anisotropy Samples Relevant To Chipmakers In The Sample Plane. This Allows For Measurements Of Wavelike Magnetic Excitations By In-elastic Light Scattering. These Measurements Will Enable Nist Then Allow To Determine The “heisenberg Exchange”., Which Will Enable Nist Together With Chipmakers To This Will Allow Nist Together With Chipmakers To Improve Models To Significantly Accelerate The Magnetic Device Development Process. ) Magnetic Field Characteristics maximum Magnetic Field Shall Be Equal To 5 Tesla Or Exceed 5 Tesla. Magnets With Larger Magnetic Field Either Standard Or Optional Will Be Given Preference. the Magnetic Field Shall Be Orientated Horizontally. the Magnetic Field Shall Be Parallel To The Room Temperature Bore. field Uniformity Over A 5 Mm Diameter Spherical Volume: ) Total Maximum Magnetic Field Change Within The Spherical Volume Shall Be Smaller Than 0.5 Mt At Any Magnetic Field Between Zero And 5 Tesla. Magnets With Better Field Uniformity Will Be Given Preference. ) Location Of The Center Of The Spherical Volume Shall Be Specified With An Uncertainty Smaller Than 1 Mm Radially And Axially With Respect To A Reference Point On The Bore Of The Magnet. ) The Location Of The Center Of The Spherical Volume Shall Be Radially Less Than Plus/minus 3 Mm Away From The Geometric Center Of The Bore With 150 Mm Diameter, Plus/minus 4 Mm Away From The Geometric Center Of The Bore With Larger Than 160 Mm Diameter And Plus/minus 5 Mm Away From The Geometric Center Of The Bore With Larger Than 165 Mm Diameter. Magnets With The Location Of The Center Of The Spherical Volume Closer To The Geometrical Center Will Be Given Preference. the Magnetic Field Compensation Shall Be Such That The Stray Field At Any Field Of The Magnet Between Zero And 5 Tesla Fulfills The Requirements Below: ) The Radial Magnetic Stray Field Shall Be At 225 Cm From The Center Of Magnet Bore Less Than 0.5 Mt, While The Maximum Magnetic Field Inside The Room Temperature Bore Is Between Zero And 5 Tesla. Magnets, Which Meet The Stray Field Requirement At A Smaller Distance Will Be Given Preference. ) The Magnetic Stray Field Shall Be Axially At 295 Cm From The Front Face Away From The Magnet Less Than 0.5 Mt, While The Maximum Magnetic Field Inside The Room Temperature Bore Is Between Zero And 5 Tesla. The Front Face Of The Magnet Shall Be The Side Without Any Possible Cold Head. Magnets, Which Meet The Stray Field Requirement At A Smaller Distance Will Be Given Preference. ) The Magnetic Stray Field Shall Be Axially At 315 Cm From The Front Face Through The Magnet Less Than 0.5 Mt While The Maximum Magnetic Field Inside The Room Temperature Bore Is Between Zero And 5 Tesla. Magnets, Which Meet The Stray Field Requirement At A Smaller Distance Will Be Given Preference. the Maximum Magnetic Field Of 5 Tesla Shall Be Reached From A Start Field Of Zero Tesla In Less Than 90 Minutes. ) Magnet Dimensions room Temperature Bore Of The Magnet Shall Have A Diameter Equal To Or Exceeding 150 Mm. Magnets With Larger Diameter Room Temperature Bore Will Be Given Preference. the Full Diameter Of The Bore Shall Be Accessible From Both Sides Of The Magnet. the Diameter Of The Magnet Including Support Structure Shall Be Less Than 135 Cm. the Magnet Without Cryo-head And Support Structure Shall Be Shorter Than 140 Cm. the Center Of The Bore Shall Be 110 Cm Above The Floor. the Magnet With Its Support Structure Needs To Fit Through Fit Through The Entrance Door Of The Laboratory, Which Is 166 Cm Wide And 208 Cm High, While Being Loaded On A Pallet Jack Or Similar Means To Move The Magnet. support Structure For Magnet magnet Support Structure Shall Have A Customer Specified Hole Pattern At The Bottom For Mounting On Linear Guide Carriages. magnet And Connections Shall Be Able To Translate Along Linear Rails Up To 2/3rds Of The Magnet Depth Without Breaking Connections. misc the Superconducting Magnet Shall Be Cooled With A Closed-cycle System Using A Pulse Tube. cryo-cooler Lines Shall Be Longer Than 18 M. power Supply For Magnet Shall Be Included And Remotely Controlled Via Analog Voltage, Usb, Ethernet Or Gpib. all Required Control Software For Operation Of The Magnet Shall Be Included. all Required Temperature Monitoring Systems Shall Be Included. optional Criteria higher Magnetic Field: Magnet Shall Produce A Magnetic Field Exceeding 5 Tesla. Magnets With Larger Magnetic Field, Higher Field Uniformity At Larger Magnetic Fields And Smaller Stray Fields At Larger Magnetic Fields Will Be Given Preference. extended Warranty/service Beyond Base For 3 Years On The Complete Magnet System Including Cryo-cooler Beyond Base. Preference Will Be Given For Longer Warranty/service. 6. Delivery Shall Be Completed No More Than 13 Months After Receipt Of Order. Delivery Will Be Made To: Doc/nist Shipping & Receiving 325 Broadway Boulder, Co 80305 how To Respond To This Notice in Responding To This Notice, Please Do Not Provide Proprietary Inforrmation. Please Include Only The Following Information, Readable In Either Microsoft Word 365, Microsoft Excel 365, Or .pdf Format, In The Response: Submit The Response By Email To The Primary Point Of Contact And, If Specified, To The Secondary Point Of Contact Specialist Listed At The Bottom Of This Notice As Soon As Possible, And Preferably Before The Closing Date And Time Of This Notice. provide The Complete Name Of Your Company, Address, Name Of Contact For Follow-up Questions, Their Email, Their Phone Number And, If Your Company Has An Active Registration In Https://sam.gov, Your Company’s Unique Entity Id (uei). identify Laboratory Equipment That Your Company Sells That Is Of The Nature Addressed In The Background Section Of This Notice. Include Brand Name, Make, Model, And/or Other Distinguishing Information. state If Your Company Is The Manufacturer Of The Identified Equipment Or Is A Retailer Or Wholesaler That Normally Sells The Identified Equipment. If The Latter, Indicate Whether The Manufacturer Authorized In Writing For Your Company To Sell The Identified Equipment On Behalf Of The Manufacturer. describe Performance Capabilities And Relevant Or Beneficial Physical And Functional Features For Any Equipment You Identified To Satisfy The Nist-identified Minimum Specifications Described In This Notice. identify Any Aspects Of The Nist Market Research Notice, Including Instructions, And Draft Minimum Specifications In The Background Section Above That Could Be Viewed As Unduly Restrictive Or Contain Unnecessary Barriers That Adversely Affect Your Ability To Fully Participate And Indicate Why. In Such A Scenario, Please Offer Suggestions For How The Market Research Notice And Draft Minimum Specifications Could Be Made More Inclusive And Competitive. discuss Whether The Equipment That Your Company Sells And Which You Describe In Your Response To This Notice May Be Customized To Specifications And Indicate Any Limits To Customization. for The Naics Code Listed In This Notice: indicate Whether Your Company Is (a) A Small Business Or (b) Other Than Small Business. See The Table Of Small Business Size Standards And The Associated .pdf Download File For Small Business Size Standards And Additional Information. if You Believe The Naics Code Listed In This Notice Is Not The Best Naics Code For The Type Of Product Addressed In This Notice, Identify An Alternative Naics Code That You Believe Would Be More Appropriate For The Planned Procurement. describe Services That Are Available With The Purchase Of The Aforementioned Equipment From Your Company Such As Installation, Training, And Equipment Maintenance. describe Standard Terms And Conditions Of Sale Offered By Your Company For The Aforementioned Equipment Such As: Delivery Time After Your Company Accepts The Order; Fob Shipping Terms: Manufacturer Warranty (including Details Regarding Nature And Duration); If Available, Description(s) Of Available Extended Warranty; Equipment Setup And Test; Operator And Service Instruction Manual(s); Cleanup After Installation; And If Applicable, Other Offered Services. Provide A Copy Of Manufacturer Standard Terms And Conditions That Typically Relate To The Sale Of The Specified Equipment, If Available. state Whether Your Company Offers Facility Renovation Services Related To Installation Of The Aforementioned Equipment At Its Delivery Destination, If Required Per The Nist-identified Minimum Specifications, And Provide Description Of Services. Indicate If Your Company Performs The Facility Renovation Services Or Typically Subcontracts The Work To Another Company. Indicate If Your Company Would Be Interested Inspecting The Intended Installation Site During The Market Research Phase. state Published Price, Discount Or Rebate Arrangements For Aforementioned Equipment And/or Provide Link To Access Company’s Published Prices For Equipment And Services. state Whether The Aforementioned Equipment Is Manufactured In The United States And, If Not, State The Name Of The Country Where The Equipment Is Manufactured. identify Any Plans/possibilities For Changes In Manufacturing Location Of The Aforementioned Equipment And Provide Relevant Details. if The Aforementioned Equipment And Related Services Are Available For Purchase On Any Existing Federal Supply Schedule Contract(s) Or Other Contracts Against Which Nist May Be Able Place Orders, Identify The Contract Number(s) And Other Relevant Information. identify Any Customers In The Public Or Private Sectors In Which You Provided The Aforementioned Or Similar Equipment. Include Customer(s) Information: Company Name, Phone Number, Point Of Contact, Email Address. provide Any Other Information That You Believe Would Be Valuable For Nist To Know As Part Of Its Market Research For This Requirement. state If You Require Nist To Provide Additional Information To Improve Your Understanding Of The Government’s Requirement And/or Would Like To Meet With Nist Representatives To Discuss The Requirement And The Capabilities Of The Identified Equipment. important Notes the Information Received In Response To This Notice Will Be Reviewed And Considered So That Nist May Appropriately Solicit For Its Requirements In The Near Future. this Notice Should Not Be Construed As A Commitment By Nist To Issue A Solicitation Or Ultimately Award A Contract. responses Will Not Be Considered As Proposals Or Quotations. no Award Will Be Made As A Result Of This Notice. nist Is Not Responsible For Any Costs Incurred By The Respondents To This Notice. nist Reserves The Right To Use Information Provided By Respondents For Any Purpose Deemed Necessary And Appropriate. thank You For Taking The Time To Submit A Response To This Request!

This Combined Synopsis/solicitation Has Hereby Been Amended To Remove Power And Installation Reuirements Of The Previous Posting And E=xtend The Due Date For Quotation. No Additonal Changes Have Been Made. this Combined Synopsis/solicitation Has Hereby Been Amended To Clarify A Question Raised By A Potential Quoter. The Delivery And Installation Location For These Ovens Is On The First Floor With An Unobstructed Route To The End Location. There Is Also A Loading Dock To This Floor With Standard Freight Access. No Additional Changes Have Been Made. the Combined Synopsis/solicitation Has Hereby Been Amended To Extend The Due Date For Quotations And Upload A Revised Minimum Specifications Document. No Additonal Changes Have Been Made. combined Synopsis/solicitation procurement Of Laboratory Ovens. this Is A Combined Synopsis/solicitation For Commercial Items Prepared In Accordance With The Format In Far Subpart 12.6 – Streamlined Procedures For Evaluation And Solicitation For Commercial Items, As Supplemented With Additional Information Included In This Notice. This Announcement Constitutes The Only Solicitation; Quotations Are Being Requested, And A Separate Written Solicitation Document Will Not Be Issued. This Solicitation Is Being Issued Under The Authority Of Far Part 13 Simplified Acquisition Procedures. the Due Date For Quotation Is 5/27/2024, 1:00pm Est this Solicitation Is A Request For Quotations (rfq). The Solicitation Document And Incorporated Provisions And Clauses Are Those In Effect Through Federal Acquisition Circular (fac) 2024-04 Effective April 1st, 2024. the Associated North American Industrial Classification System (naics) Code For This Procurement Shall Be 333994- Industrial Process Furnace And Oven Manufacturing With A Small Business Size Standard Of 500 Employees. this Acquisition Is Being Procured As A 100% Small Business Set Aside. Responsible Quoters Shall Provide Pricing For The Following Line Items: line Item 0001: Laboratory Oven In Accordance With The Specifications In The Attached Requirements Document. line Item 0002: Laboratory Oven In Accordance With The Specifications In The Attached Requirements Document. delivery delivery And Installation Shall Occur Within 90 Days Of Award Of This Requirement. questions Regarding This Synopsis/solicitation Can Be Emailed To Erik.frycklund@nist.gov Evaluation Criteria And Basis For Award the Government Intends To Award A Purchase Order Resulting From This Solicitation To The Responsible Quoter Whose Quotation, Conforming To The Solicitation, Is The Lowest Price, Technically Acceptable Quotation. technically Acceptable Means That The Contractor’s Provide Equipment Meeting The Minimum Requirements In The requirements Document. price Will Be Evaluated For All Quoters Whose Quotations Are Determined Technically Acceptable. Price Will Be Evaluated To Determine That Total Price Is Consistent With The Technical Portion Of The Quotation And Is A Fair And Reasonable Overall Price To The Government. the Contracting Officer May, If Necessary, Request Revised Quotation(s) Prior To Award. Required Submissions all Contractors Shall Submit The Following: for The Purpose Of Evaluation Of Technical Acceptability: quoters Shall Provide Documentation That Demonstrates The Quoted Product’s Ability To Meet Or Exceed The minimum Specifications In Accordance With The Requirements Document. For The Purpose Of Price: quoters Shall Provide Firm-fixed Price Quotations For Line Items quoters Shall Include A Completed Copy Of All Required Solicitation Provisions Contained In The Attached Applicable Provisions/clauses Document (required Provisions Are Highlighted) any Award Resulting From This Solicitation Will Contain The Following Statement: “the Government’s Terms And Conditions, Identified Herein, Shall Be The Prevailing Terms And Conditions Governing This Award. In The Event Of A Conflict Between The Government’s And Contractor’s Terms And Conditions, The Government’s Terms And conditions Take Precedence.” If The Contractor Objects To Any Of The Terms And Conditions Contained In This solicitation, The Contractor Shall State “the Terms And Conditions In The Solicitation Are Acceptable To Be Included In The Award Document With The Exception, Deletion, Or Addition Of The Following:” [contractor Shall List Exception(s) And Rationale For The Exception(s)]. It Is The Sole Responsibility Of The Contractor To Identify In Their Quote Any Exceptions To The Terms And Conditions Of The Solicitation. If The Contractor Does Not Include Such A Statement, The Submission Of A Quotation In Response To This Solicitation Will Be Regarded As The Contractor’s Acceptance Of The government’s Terms And Conditions For Inclusion Into The Resultant Purchase Order As Prevailing. quoters Shall Provide An Active Government Unique Identifier Number For The System For Award Management (sam) Registration. Quoters Must Have An Active Registration At Www.sam.gov In Order To Be Technically Evaluated. quoters Shall Provide The Location Of Product Manufacturer To Be Either Domestic Or Foreign. If Non Domestic, The Country Of Origin Must Be Listed. please Note That This Procurement Is Not Being Conducted Under The Gsa Federal Supply Schedule (fss) Program Or Another Government-wide Area Contract (gwac). If A Contractor Submits A Quotation Based Upon An Fss Or Gwac Contract, The Government Will Accept The Quoted Price. However, The Terms And Conditions Stated Herein Will Be Included In Any Resultant Purchase Order, Not The Terms And Conditions Of The Contractor’s Fss Or Gwac Contract, And The Statement Required Above Shall Be Included In The Quotation. provisions And Clauses: the Clauses And Provisions Applicable To This Solicitation Can Be Found Under Applicable Clauses & Provisions. The Full Text Of A Far Provision Or Clause May Be Accessed Electronically At Www.acquisition.gov/far. The Full Text Of A Car Provision Or Clause May Be Accessed Electronically At Or Http://www.osec.doc.gov/oam/acquistion_management/policy/. attachments: the Following Attachments Apply To This Solicitation: the Requirements Document applicable Clauses & Provisions

Maintenance Service Contract For Two (2) Zeiss Axioscan Automated Slide Scanner Systems

Combined Synopsis/solicitation procurement Of A Cutting Mill this Is A Combined Synopsis/solicitation For Commercial Items Prepared In Accordance With The Format In Far Subpart 12.6 – Streamlined Procedures For Evaluation And Solicitation For Commercial Items, As Supplemented With Additional Information Included In This Notice. This Announcement Constitutes The Only Solicitation; Quotations Are Being Requested, And A Separate Written Solicitation Document Will Not Be Issued. This Solicitation Is Being Issued Under The Authority Of Far Part 13 Simplified Acquisition Procedures. the Due Date For Quotation Is 8/5/2024, 1:00pm Est this Solicitation Is A Request For Quotations (rfq). The Solicitation Document And Incorporated Provisions And Clauses Are Those In Effect Through Federal Acquisition Circular (fac) 2024-05 Effective May 22, 2024. the Associated North American Industrial Classification System (naics) Code For This Procurement Shall Be 334516- Analytical Laboratory Instrument Manufacturing With A Small Business Size Standard Of 1000 Employees this Acquisition Is Being Procured As A Full And Open Competition responsible Quoters Shall Provide Pricing For The Following Line Items: line Item 0001: One Cutting Mill Accordance With The Specifications In The Attached Requirements Document. delivery delivery: Shall Occur Within 150 Days Of Award Of This Requirement. questions Regarding This Synopsis/solicitation Can Be Emailed To Erik.frycklund@nist.gov Evaluation Criteria And Basis For Award the Government Intends To Award A Purchase Order Resulting From This Solicitation To The Responsible Quoter Whose Quotation, Conforming To The Solicitation, Is The Lowest Price, Technically Acceptable Quotation. technically Acceptable Means That The Contractor’s Provide Equipment Meeting The Minimum Requirements In The requirements Document. price Will Be Evaluated For All Quoters Whose Quotations Are Determined Technically Acceptable. Price Will Be Evaluated To Determine That Total Price Is Consistent With The Technical Portion Of The Quotation And Is A Fair And Reasonable Overall Price To The Government. the Contracting Officer May, If Necessary, Request Revised Quotation(s) Prior To Award. Required Submissions all Contractors Shall Submit The Following: for The Purpose Of Evaluation Of Technical Acceptability: quoters Shall Provide Documentation That Demonstrates The Quoted Product’s Ability To Meet Or Exceed The minimum Specifications In Accordance With The Requirements Document. For The Purpose Of Price: quoters Shall Provide Firm-fixed Price Quotations For Line Items quoters Shall Include A Completed Copy Of All Required Solicitation Provisions Contained In The Attached Applicable Provisions/clauses Document (required Provisions Are Highlighted) any Award Resulting From This Solicitation Will Contain The Following Statement: “the Government’s Terms And Conditions, Identified Herein, Shall Be The Prevailing Terms And Conditions Governing This Award. In The Event Of A Conflict Between The Government’s And Contractor’s Terms And Conditions, The Government’s Terms And conditions Take Precedence.” If The Contractor Objects To Any Of The Terms And Conditions Contained In This solicitation, The Contractor Shall State “the Terms And Conditions In The Solicitation Are Acceptable To Be Included In The Award Document With The Exception, Deletion, Or Addition Of The Following:” [contractor Shall List Exception(s) And Rationale For The Exception(s)]. It Is The Sole Responsibility Of The Contractor To Identify In Their Quote Any Exceptions To The Terms And Conditions Of The Solicitation. If The Contractor Does Not Include Such A Statement, The Submission Of A Quotation In Response To This Solicitation Will Be Regarded As The Contractor’s Acceptance Of The government’s Terms And Conditions For Inclusion Into The Resultant Purchase Order As Prevailing. quoters Shall Provide An Active Government Unique Identifier Number For The System For Award Management (sam) Registration. Quoters Must Have An Active Registration At Www.sam.gov In Order To Be Technically Evaluated. quoters Shall Provide The Location Of Product Manufacturer To Be Either Domestic Or Foreign. If Non Domestic, The Country Of Origin Must Be Listed. please Note That This Procurement Is Not Being Conducted Under The Gsa Federal Supply Schedule (fss) Program Or Another Government-wide Area Contract (gwac). If A Contractor Submits A Quotation Based Upon An Fss Or Gwac Contract, The Government Will Accept The Quoted Price. However, The Terms And Conditions Stated Herein Will Be Included In Any Resultant Purchase Order, Not The Terms And Conditions Of The Contractor’s Fss Or Gwac Contract, And The Statement Required Above Shall Be Included In The Quotation. provisions And Clauses: the Clauses And Provisions Applicable To This Solicitation Can Be Found Under Applicable Clauses & Provisions. The Full Text Of A Far Provision Or Clause May Be Accessed Electronically At Www.acquisition.gov/far. The Full Text Of A Car Provision Or Clause May Be Accessed Electronically At Or Http://www.osec.doc.gov/oam/acquistion_management/policy/. attachments: the Following Attachments Apply To This Solicitation: the Requirements Document applicable Clauses & Provisions

Background semiconductor Manufacturing Yield Enhancement Requires Ongoing Risk Analysis Of Cleaning Chemical Purity Wherein Critical Contaminants Are Already At Levels Difficult Or Impossible To Detect, Let Alone Identify And Quantify. Next Generation Chips Will Require Even Purer Materials And Advanced Metrological Capabilities For The Detection, Identification, And Quantification Of Impurities In Semiconductor Cleaning Chemicals Necessitating A Practical Roadmap For Assessing Material Purity Commensurate With The Needs Of The Next Generation In Semiconductor Manufacturing. The International Roadmap For Devices And Systems (irds) Has Identified That A “lack Of Proven Particle Metrology Limits The Ability To Confirm Whether Uf (ultrafiltration Of Upw) Is Effective In Controlling Killer Size Particles Down To The Critical Particle Size”. aerosol-based Testing Of Uf Will Require Nebulizing And Drying A Ultra-pure Water (upw) Stream To Form An Aerosol And Simultaneously Measuring The Upstream And Downstream Particle Size Distributions And Number Densities. This Aerosolization Process Directly Mimics What Occurs On-wafer. These Aerosol-based Methods Are Quickly Gaining Acceptance And Nist Research Would Speed These Efforts. specifically, We Require Two Nanoparticle Nebulizers That Can Generate, From Water, Ultrafine Native Particles (those Existing At Or Near Their Actual Size In Water) With Sizes < 10 Nm And Minimizes The Effect Of Non-volatile Particle Precursors (materials That Form Particles Upon Aerosolization And Drying). the Nanoparticle Nebulizers Will Be Used In A Standard Indoor Chemistry Laboratory With Temperatures Between 18°c And 24 °c And Relative Humidities Between 20 % And 80 % (non-condensing) And Standard 120 V 20 A/30a Power. the Nanoparticle Nebulizers Serve As Components In A Larger System Designed To Measure The Efficiency Of A Laboratory-scale Uf System That Has Been Configured For The Quantitative Determination Of Uf Efficiency To Particles With Sizes Spanning ≈1nm To ≈50nm And A Range Of Chemistries And Morphologies (e.g., Spherical, Rod, Etc.). Ideally, The Nanoparticle Nebulizers Can Generate Particles From Cleaning Chemicals Such As Isopropyl Alcohol, Hydrogen Peroxide, Ammonia, And Dilute Hydrochloric Acid Where Uf Is Needed. nist Is Seeking Information From Sources That May Be Capable Of Providing A Commercial Solution That Will Achieve The Objectives Described Above. In Addition To The Above, Below Are Additional Line-item Descriptions That Includes Specifics On Essential Requirements: line Item 0001: Nanoparticle Nebulizer description: Particle Generator That Minimizes Interference From Non-volatile Particle Precursors. quantity: 2 technical Specifications does Not Require A Conductive Solution To Generate Aerosol. capable Of Nebulizing, From Water, Native Particles Smaller Than 10 Nm With Minimal Interference From Non-volatile Residues In The Solution. utilizes 120 Vac. how To Respond To This Notice in Responding To This Notice, Please Do Not Provide Proprietary Information. Please Include Only The Following Information, Readable In Either Microsoft Word 365, Microsoft Excel 365, Or .pdf Format, In The Response: Submit The Response By Email To The Primary Point Of Contact And, If Specified, To The Secondary Point Of Contact Listed In This Notice As Soon As Possible, And Preferably Before The Closing Date And Time Of This Notice. Please Note That To Be Considered For Award Under Any Official Solicitation, The Entity Must Be Registered And “active” In Sam At The Time Of Solicitation Response. provide The Complete Name Of Your Company, Address, Name Of Contact For Follow-up Questions, Their Email, Their Phone Number And, If Your Company Has An Active Registration In Https://sam.gov, Your Company’s Unique Entity Id (uei). identify The Equipment That Your Company Sells That Can Meet The Objectives Addressed In The Background Section Of This Notice. For Each Product Recommended To Meet The Government’s Requirement, Provide The Following: manufacturer Name model Number technical Specifications if Your Company Is Not The Manufacturer, Provide Information On Your Company’s Status As An Authorized Reseller Of The Product(s) describe Performance Capabilities Of The Product(s) Your Company Recommends To Meet The Government’s Requirements. Additionally, If There Are Other Features Or Functions That You Believe Would Assist Nist In Meeting Its Objectives Described Above, Please Discuss In Your Response. discuss Whether The Equipment That Your Company Sells And Which You Describe In Your Response To This Notice May Be Customized To Specifications And Indicate Any Limits To Customization. identify Any Aspects Of The Nist Market Research Notice, Including Instructions, And Draft Minimum Specifications In The Background Section You Cannot Meet And State Why. Please Offer Suggestions For How The Market Research Notice And Draft Minimum Specifications Could Be Made More Competitive. state Whether The Proposed Equipment Is Manufactured In The United States And, If Not, State The Name Of The Country Where The Equipment Is Manufactured. identify Any Plans/possibilities For Changes In Manufacturing Location Of The Aforementioned Equipment And Provide Relevant Details, Including Timeline. for The Naics Code Listed In This Notice: indicate Whether Your Company Is (a) A Small Business Or (b) Other Than Small Business. See The Table Of Small Business Size Standards And The Associated .pdf Download File For Small Business Size Standards And Additional Information. if You Believe The Naics Code Listed In This Notice Is Not The Best Naics Code For The Type Of Product Addressed In This Notice, Identify An Alternative Naics Code That You Believe Would Be More Appropriate For The Planned Procurement. describe Services That Are Available With The Purchase Of The Aforementioned Equipment From Your Company Such As Installation, Training, And Equipment Maintenance. describe Standard Terms And Conditions Of Sale Offered By Your Company For The Recommended Equipment Such As: Delivery Time After Your Company Accepts The Order; Fob Shipping Terms; Manufacturer Warranty (including Details Regarding Nature And Duration); If Available, Description(s) Of Available Extended Warranty; Equipment Setup And Test; Operator And Service Instruction Manual(s); Cleanup After Installation; And If Applicable, Other Offered Services. Provide A Copy Of Manufacturer Standard Terms And Conditions That Typically Relate To The Sale Of The Specified Equipment, If Available. state Whether Your Company Offers Facility Renovation Services Related To Installation Of The Recommended Equipment At Its Delivery Destination, If Required Per The Nist-identified Minimum Specifications, And Provide Description Of Said Services. Indicate If Your Company Performs The Facility Renovation Services Or Typically Subcontracts The Work To Another Company. Indicate If Your Company Would Be Interested In Inspecting The Intended Installation Site During The Market Research Phase. state Published Price, Discount, Or Rebate Arrangements For Recommended Equipment And/or Provide Link To Access Company’s Published Prices For Equipment And Services. if The Recommended Equipment And Related Services Are Available For Purchase On Any Existing Federal Supply Schedule Contract(s) Or Other Contracts Against Which Nist May Be Able To Place Orders, Identify The Contract Number(s) And Other Relevant Information. identify Any Customers In The Public Or Private Sectors To Which You Provided The Recommended Or Similar Equipment. Include Customer(s) Information: Company Name, Phone Number, Point Of Contact, Email Address. provide Any Other Information That You Believe Would Be Valuable For Nist To Know As Part Of Its Market Research For This Requirement. state If You Require Nist To Provide Additional Information To Improve Your Understanding Of The Government’s Requirement And/or Would Like To Meet With Nist Representatives To Discuss The Requirement And The Capabilities Of The Identified Equipment. questions Regarding This Notice questions Regarding This Notice May Be Submitted Via Email To The Primary Point Of Contact And The Secondary Point Of Contact Listed In This Notice. Questions Should Be Submitted So That They Are Received 5 Days Prior To The Response Date. If The Contracting Officer Determines That Providing A Written Amendment To This Notice To Document Question(s) Received Would Benefit Other Potential Respondents, The Questions Would Be Anonymized, And A Written Response To Such Question(s) Would Be Provided Via An Amendment To This Notice. important Notes this Notice Is For Market Research Purposes And Should Not Be Construed As A Commitment By Nist To Issue A Solicitation Or Ultimately Award A Contract. There Is No Solicitation Available At This Time. this Notice Does Not Obligate The Government To Award A Contract Or Otherwise Pay For The Information Provided In Response. nist Reserves The Right To Use Information Provided By Respondents For Any Purpose Deemed Necessary And Legally Appropriate. any Organization Responding To This Notice Should Ensure That Its Response Is Complete And Sufficiently Detailed To Allow The Government To Determine The Organization’s Capability. respondents Are Advised That The Government Is Under No Obligation To Acknowledge Receipt Of The Information Received Or Provide Feedback To Respondents With Respect To Any Information Submitted. after A Review Of The Responses Received, A Synopsis And Solicitation May Be Published On Gsa’s Ebuy Or Sam.gov. However, Responses To This Notice Will Not Be Considered An Adequate Response To Any Such Solicitation(s). the Responses Shall Not Exceed 5 Pages Including All Attachments, Charts, Etc. thank You For Taking The Time To Submit A Response To This Request!

Quantitative Analytical Testing