NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY USA Tender

Background nist Is Seeking Information From Sources That May Be Capable Of Providing A Commercial Item Solution That Meets Or Exceeds The Following Draft Minimum Specifications. The Required Item Is A Superconducting Magnet With A Room Temperature Bore, Which Will Be Used In Our Laboratory, That Produces A Sufficiently Large Magnetic Field To Saturate High Perpendicular Anisotropy Samples Relevant To Chipmakers In The Sample Plane. This Allows For Measurements Of Wavelike Magnetic Excitations By In-elastic Light Scattering. These Measurements Will Enable Nist Then Allow To Determine The “heisenberg Exchange”., Which Will Enable Nist Together With Chipmakers To This Will Allow Nist Together With Chipmakers To Improve Models To Significantly Accelerate The Magnetic Device Development Process. ) Magnetic Field Characteristics maximum Magnetic Field Shall Be Equal To 5 Tesla Or Exceed 5 Tesla. Magnets With Larger Magnetic Field Either Standard Or Optional Will Be Given Preference. the Magnetic Field Shall Be Orientated Horizontally. the Magnetic Field Shall Be Parallel To The Room Temperature Bore. field Uniformity Over A 5 Mm Diameter Spherical Volume: ) Total Maximum Magnetic Field Change Within The Spherical Volume Shall Be Smaller Than 0.5 Mt At Any Magnetic Field Between Zero And 5 Tesla. Magnets With Better Field Uniformity Will Be Given Preference. ) Location Of The Center Of The Spherical Volume Shall Be Specified With An Uncertainty Smaller Than 1 Mm Radially And Axially With Respect To A Reference Point On The Bore Of The Magnet. ) The Location Of The Center Of The Spherical Volume Shall Be Radially Less Than Plus/minus 3 Mm Away From The Geometric Center Of The Bore With 150 Mm Diameter, Plus/minus 4 Mm Away From The Geometric Center Of The Bore With Larger Than 160 Mm Diameter And Plus/minus 5 Mm Away From The Geometric Center Of The Bore With Larger Than 165 Mm Diameter. Magnets With The Location Of The Center Of The Spherical Volume Closer To The Geometrical Center Will Be Given Preference. the Magnetic Field Compensation Shall Be Such That The Stray Field At Any Field Of The Magnet Between Zero And 5 Tesla Fulfills The Requirements Below: ) The Radial Magnetic Stray Field Shall Be At 225 Cm From The Center Of Magnet Bore Less Than 0.5 Mt, While The Maximum Magnetic Field Inside The Room Temperature Bore Is Between Zero And 5 Tesla. Magnets, Which Meet The Stray Field Requirement At A Smaller Distance Will Be Given Preference. ) The Magnetic Stray Field Shall Be Axially At 295 Cm From The Front Face Away From The Magnet Less Than 0.5 Mt, While The Maximum Magnetic Field Inside The Room Temperature Bore Is Between Zero And 5 Tesla. The Front Face Of The Magnet Shall Be The Side Without Any Possible Cold Head. Magnets, Which Meet The Stray Field Requirement At A Smaller Distance Will Be Given Preference. ) The Magnetic Stray Field Shall Be Axially At 315 Cm From The Front Face Through The Magnet Less Than 0.5 Mt While The Maximum Magnetic Field Inside The Room Temperature Bore Is Between Zero And 5 Tesla. Magnets, Which Meet The Stray Field Requirement At A Smaller Distance Will Be Given Preference. the Maximum Magnetic Field Of 5 Tesla Shall Be Reached From A Start Field Of Zero Tesla In Less Than 90 Minutes. ) Magnet Dimensions room Temperature Bore Of The Magnet Shall Have A Diameter Equal To Or Exceeding 150 Mm. Magnets With Larger Diameter Room Temperature Bore Will Be Given Preference. the Full Diameter Of The Bore Shall Be Accessible From Both Sides Of The Magnet. the Diameter Of The Magnet Including Support Structure Shall Be Less Than 135 Cm. the Magnet Without Cryo-head And Support Structure Shall Be Shorter Than 140 Cm. the Center Of The Bore Shall Be 110 Cm Above The Floor. the Magnet With Its Support Structure Needs To Fit Through Fit Through The Entrance Door Of The Laboratory, Which Is 166 Cm Wide And 208 Cm High, While Being Loaded On A Pallet Jack Or Similar Means To Move The Magnet. support Structure For Magnet magnet Support Structure Shall Have A Customer Specified Hole Pattern At The Bottom For Mounting On Linear Guide Carriages. magnet And Connections Shall Be Able To Translate Along Linear Rails Up To 2/3rds Of The Magnet Depth Without Breaking Connections. misc the Superconducting Magnet Shall Be Cooled With A Closed-cycle System Using A Pulse Tube. cryo-cooler Lines Shall Be Longer Than 18 M. power Supply For Magnet Shall Be Included And Remotely Controlled Via Analog Voltage, Usb, Ethernet Or Gpib. all Required Control Software For Operation Of The Magnet Shall Be Included. all Required Temperature Monitoring Systems Shall Be Included. optional Criteria higher Magnetic Field: Magnet Shall Produce A Magnetic Field Exceeding 5 Tesla. Magnets With Larger Magnetic Field, Higher Field Uniformity At Larger Magnetic Fields And Smaller Stray Fields At Larger Magnetic Fields Will Be Given Preference. extended Warranty/service Beyond Base For 3 Years On The Complete Magnet System Including Cryo-cooler Beyond Base. Preference Will Be Given For Longer Warranty/service. 6. Delivery Shall Be Completed No More Than 13 Months After Receipt Of Order. Delivery Will Be Made To: Doc/nist Shipping & Receiving 325 Broadway Boulder, Co 80305 how To Respond To This Notice in Responding To This Notice, Please Do Not Provide Proprietary Inforrmation. Please Include Only The Following Information, Readable In Either Microsoft Word 365, Microsoft Excel 365, Or .pdf Format, In The Response: Submit The Response By Email To The Primary Point Of Contact And, If Specified, To The Secondary Point Of Contact Specialist Listed At The Bottom Of This Notice As Soon As Possible, And Preferably Before The Closing Date And Time Of This Notice. provide The Complete Name Of Your Company, Address, Name Of Contact For Follow-up Questions, Their Email, Their Phone Number And, If Your Company Has An Active Registration In Https://sam.gov, Your Company’s Unique Entity Id (uei). identify Laboratory Equipment That Your Company Sells That Is Of The Nature Addressed In The Background Section Of This Notice. Include Brand Name, Make, Model, And/or Other Distinguishing Information. state If Your Company Is The Manufacturer Of The Identified Equipment Or Is A Retailer Or Wholesaler That Normally Sells The Identified Equipment. If The Latter, Indicate Whether The Manufacturer Authorized In Writing For Your Company To Sell The Identified Equipment On Behalf Of The Manufacturer. describe Performance Capabilities And Relevant Or Beneficial Physical And Functional Features For Any Equipment You Identified To Satisfy The Nist-identified Minimum Specifications Described In This Notice. identify Any Aspects Of The Nist Market Research Notice, Including Instructions, And Draft Minimum Specifications In The Background Section Above That Could Be Viewed As Unduly Restrictive Or Contain Unnecessary Barriers That Adversely Affect Your Ability To Fully Participate And Indicate Why. In Such A Scenario, Please Offer Suggestions For How The Market Research Notice And Draft Minimum Specifications Could Be Made More Inclusive And Competitive. discuss Whether The Equipment That Your Company Sells And Which You Describe In Your Response To This Notice May Be Customized To Specifications And Indicate Any Limits To Customization. for The Naics Code Listed In This Notice: indicate Whether Your Company Is (a) A Small Business Or (b) Other Than Small Business. See The Table Of Small Business Size Standards And The Associated .pdf Download File For Small Business Size Standards And Additional Information. if You Believe The Naics Code Listed In This Notice Is Not The Best Naics Code For The Type Of Product Addressed In This Notice, Identify An Alternative Naics Code That You Believe Would Be More Appropriate For The Planned Procurement. describe Services That Are Available With The Purchase Of The Aforementioned Equipment From Your Company Such As Installation, Training, And Equipment Maintenance. describe Standard Terms And Conditions Of Sale Offered By Your Company For The Aforementioned Equipment Such As: Delivery Time After Your Company Accepts The Order; Fob Shipping Terms: Manufacturer Warranty (including Details Regarding Nature And Duration); If Available, Description(s) Of Available Extended Warranty; Equipment Setup And Test; Operator And Service Instruction Manual(s); Cleanup After Installation; And If Applicable, Other Offered Services. Provide A Copy Of Manufacturer Standard Terms And Conditions That Typically Relate To The Sale Of The Specified Equipment, If Available. state Whether Your Company Offers Facility Renovation Services Related To Installation Of The Aforementioned Equipment At Its Delivery Destination, If Required Per The Nist-identified Minimum Specifications, And Provide Description Of Services. Indicate If Your Company Performs The Facility Renovation Services Or Typically Subcontracts The Work To Another Company. Indicate If Your Company Would Be Interested Inspecting The Intended Installation Site During The Market Research Phase. state Published Price, Discount Or Rebate Arrangements For Aforementioned Equipment And/or Provide Link To Access Company’s Published Prices For Equipment And Services. state Whether The Aforementioned Equipment Is Manufactured In The United States And, If Not, State The Name Of The Country Where The Equipment Is Manufactured. identify Any Plans/possibilities For Changes In Manufacturing Location Of The Aforementioned Equipment And Provide Relevant Details. if The Aforementioned Equipment And Related Services Are Available For Purchase On Any Existing Federal Supply Schedule Contract(s) Or Other Contracts Against Which Nist May Be Able Place Orders, Identify The Contract Number(s) And Other Relevant Information. identify Any Customers In The Public Or Private Sectors In Which You Provided The Aforementioned Or Similar Equipment. Include Customer(s) Information: Company Name, Phone Number, Point Of Contact, Email Address. provide Any Other Information That You Believe Would Be Valuable For Nist To Know As Part Of Its Market Research For This Requirement. state If You Require Nist To Provide Additional Information To Improve Your Understanding Of The Government’s Requirement And/or Would Like To Meet With Nist Representatives To Discuss The Requirement And The Capabilities Of The Identified Equipment. important Notes the Information Received In Response To This Notice Will Be Reviewed And Considered So That Nist May Appropriately Solicit For Its Requirements In The Near Future. this Notice Should Not Be Construed As A Commitment By Nist To Issue A Solicitation Or Ultimately Award A Contract. responses Will Not Be Considered As Proposals Or Quotations. no Award Will Be Made As A Result Of This Notice. nist Is Not Responsible For Any Costs Incurred By The Respondents To This Notice. nist Reserves The Right To Use Information Provided By Respondents For Any Purpose Deemed Necessary And Appropriate. thank You For Taking The Time To Submit A Response To This Request!