Northern Railway Tender

Supply and installation of End plug for OFC cable item. Inspection: Site Engineer. 5

Supply and installation of Cable sealing plug for OFC cable. Inspection : Site Engineer

Supply and installation of Plastic Coupler- Slip fit/ Push fit type for OFC cable. Inspection : Site Engineer

HDD Boring & Trenchless of 120mm dia. without HDPE pipe for laying of signalling/ telecom / power cable under Track /Road/Culvert etc. cable laying is covered separately. Inspection: Site Engineer

Supply of Power Cable 1X16 Sq. mm as per specification IS:694/2010 or latest for commissioning of IPS (Insulation color Red & Black in the ratio of 1:1). Inspection by RDSO

Supply and installation of 24-40V/5A DC-DC convertor module suitable for IPS systems as per instruction of Site Incharge and RDSO spec No. RDSO/ SPN/ 165/ 2012 ver.3.0 or latest. Inspection: Supply- RDSO, Installation- Site Incharge

"Supply, Installation & Commissioning of maintenance free earth suitable kit as per RDSO Specification no. RDSO/SPN/197/2008 and Drg No. SDO/./E&B/001 dated:- 19.09.2008 and Drg No. RDSO/SDO/./E&B/002 dated:- 19.09.2008. Earthing kit consisting of earthing electrode of 17mm dia as 3m long -01 no 2 MEEB (300mmx25mmx6mm) -o1 no. 3. SEEB (150mmx25mmx6mm) -01 no 4. Earth enhancing compound - 30 kg (minimum). This includes:- Provision of earth connection from MEEB to S&T equipment i.e. cable sheath, apparatus case, BPAC, Axle counter, IPS, Data Logger etc. 10 with PVC earth wire of size 25/35 sq.mm through copper lugs of suitable size PVC earth wire shall be supplied by contractor. Note: At certain locations, it may not be possible to achieve earth resistance of less than 1.0 ohm with one earth electrode /pit due to soil resistivity. In such cases, provision of loop earth consisting of more than one earth pit shall be done, for interconnection of two earth pits copper tape of size 25x2 sq.mm shall be provided by the contractor. The No's of pits required shall be decided based on the resistance achieved for the earth pits already installed. The procedure mentioned above for one earth pit shall be repeated for other earth pits. The other earth so installed for the purpose of loop earthing arrangement shall be counted as seperate earth. Inspection : RDSO for supply ,Site engineer for Execution.

Fabrication, supply and fixing of cable termination board of size 2200mmx900mm as per Drg. No. NR/S&T/CON/4-1/97A made of angel iron size 40mmx40mmx5mm along with outer frame made of angle iron size 65mmx65mmx8mm duly fitted with Bakelite sheet (HYLAM MAKE or similar ) of size 6mm thick. This also includes fixing of ARA terminals/strips/Wago connectors & fuse bases etc. 11 Supply and fixing of hard wood of size 70cmx25cmx4cm in the back at bottom for jamming of armour of cables, each cable in the hole drilled separately for each cable through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering. All the fixing materials like bolts, nuts, washers, Insulators, shoe, angle irons, flats, L- bolts, Catenary wires & cement concretes etc. will be supplied by the contractor. This includes cleaning, priming by red oxide, painting & description etc. with ISI mark paints. Inspection :Site Engineer

Supply & Installation of Thermo shrink jointing kit for 6-Quad/4-Quad cable for straight 12 through joints as per specifications, drawings and stipulations of tender documents and as per approved cable route plan at various locations. Jointing kits to be supplied as per RDSO specification IRS:TC 77-2012 (Rev.-3) or latest amendments. Inspection : Consignee.

Supply of single app. case steel RE with 'E' type lock and key ward no.42 and handle as per drg. No. RE/S&T/ALD/SK/219/82 with (Alt A) and 221/82 with Alt.B. Inspection :Rites

"Casting, concreting and curing of foundation and erection of single app. cases of size (1160mmx760mm) at surface and 650mm deep as per approved Drg.No.NR/S&T/CON/2-7/97. A layer 14 of 3 mm of bitumen compound has to be provided between foundation and location box to prevent ingress of water in the base of location box. All material such as cement, coarse sand, aggregate and anchor bolt shall be supplied by contractor. App. Case single will be supplied by Railway. Contractor is required to execute all type of repair Works of foundations if required during inserting the cable for termination. Inspection: Site Engineer."

Preparation of App. Case single involving wiring of relays. Preparation & fixing of bakelite hylum sheet 910x800x6mm and backelite shelf 900x450x10mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location boxes secured by nuts and bolts. This includes fixing of fuses, ARA terminal, Q series relays and other type relays on square bars fixing and jamming of cables with 2-inch thick salwood plank provided at the bottom. This will include opening, pasting and jamming armour of each cable in the hole drilled separately for each cable through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering. Wiring description for terminal drawing of circuits, inside app. Case. Painting from out-side as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including Backelite shelf, hylum board, salwood plank, angle iron square bar, wire and wiring material as per the IRS specn., non-deteriorating type HRC fuses with bases, catenary wires, nuts and bolts and other items shall be supplied by the contractor. Relays, ARA terminals only shall be supplied by the Railways. Inspection: Site Engineer.

Preparation of App. Case single not involving wiring of relays. Preparation & fixing of bakelite hylum sheet 910x800x6mm and Backelite shelf 900x450x10mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location boxes secured by nuts and bolts. This includes fixing of fuses, ARA terminal and fixing and jamming of cables with 2-inch thick salwood plank provided at the bottom. This will include opening, pasting and jamming armour of each cable in 16 the hole drilled separately for each cable through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering. Wiring description for terminal drawing of circuits, inside app. Case. Painting from out-side as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including Backelite shelf, hylum board, salwood plank, angle iron square bar, wire and wiring material as per the IRS specn., non-deteriorating type HRC fuses with bases, catenary wires, nuts and bolts and other items shall be supplied by the contractor. ARA terminals only shall be supplied by the Railways. Inspection: Site Engineer.

Supply of apparatus case steel RE half with E type lock and key ward no.42 and handle as per drg.no. RE/S&T/ALD/SK/220/82 and 221/82 with Alt.B. Inspection : Consignee

Casting, concreting and curing of foundation and erection of half app. cases of size (670mmx760mm) and 650mm deep as per Drg.No.NR/S&T/CON/2. 8/97. A layer of 3 mm of bitumen 18 compound has to be provided between foundation and location box to prevent ingress of water in the base of location box. All material such as cement, coarse sand, aggregate and anchor bolt shall be supplied by contractor. App. Case half will be supplied by Railway. Contractor is required to execute all type of repair Works of foundations if required during inserting the cable for termination. Inspection: Site Engineer.

Preparation of App. Case half not involving wiring of relays. Preparation and fixing of Bakelite hylum sheet 450x800x6mm and Backelite shelf 450x450x10mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location box secured by nuts and bolts. This includes fixing of fuse ARA terminal and fixing and jamming of cable with 2-inch thick salwood plank provided at the bottom. This will include opening, pasting and jamming armour of each cable in the 19 hole drilled separately for each cable through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering. Wiring description for terminal drawing of circuits, inside app. Case. Painting from out-side as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including Backelite shelf, hylum board, salwood plank, angle iron square bar, wire and wiring material as per the IRS specification, non-deteriorating type HRC fuses with bases, catenary wires, nuts and bolts and other items shall be supplied by the contractor. Relays, ARA terminals only shall be supplied by the Railways. Inspection: Site Engineer.

Supply and installation of earth electrodes as per std. practice. The item includes digging of pit in earth, 3 Mtrs. deep and fixing earth electrode pipe. Casting of cement concrete enclosures as per drg. No. (NR/S&T/CON/6.4/97). The soil treatment shall be done as per std. practice. The item includes provn. of mild steel flat of size 35mm x 6mm (as per IRSEM) and nut bolted connection of MS flat with earth electrode. The other end of mild steel flat to be connected to block instrument, cable sheath of power equipment, signal base, apparatus case, CT rack / relay racks, other equipment's as per the instruction of Engr. at site & IRSEM. Earthing connection location to location shall be done through cable which shall be provided by Railway. Complete materials such as earth electrodes as per drg. No. ( NR/S&T/CON/6. 3/97), cement, wiring material, nut bolt for connection & mild steel flat of size 35mm x 6mm or 210 sqm as per SEM etc. to be supplied by the contractor. Inspection : Site Engineer

Testing & meggering of all types of outdoor cables after its laying and termination on 21 both ends under supervision of Railway representative. This also includes preparation of test report for core to core and core to earth on prescribed proforma for each core of the cable separately. This also include dressing and lacing of cable on both ends. Proforma for testing and material for lacing to be supplied by the contractor. Inspection: Site Engineer.

Excavating and refilling of trench in Normal Soil to the level of ground with rammed 22 earth as per approved Drg. No.NR/S&T/CON/1-1/97A. Aso as not to form a drain 0.3 Mtrs. Wide & 1 Mtr. Deep on both side of the station alongside the track. It shall conform to the safe distance as per signalling and cable plan. It also includes clearance of roots of trees & bushes. Inspection: Site Engineer.

Excavating and refilling of trench in Rocky soil to the level of ground with rammed earth as per approved Drg. No.NR/S&T/CON/1-1/97-A1 so as not to form a drain 0.3 Mtrs. Wide & 23 0.5Mtr. Deep on both side of the station alongside the track. This includes 50mm thick concreting work throughout in 1:3:6 ratio. All concreting material to be supplied by the contractor. It shall conform to the safe distance as per signalling and cable plan It also includes clearance of routes of trees & bushes. Inspection: Site Engineer.

Supply and laying of 2nd class bricks in the trench and laying as per approved Drg. No.NR/S&T/CON/1- 1/97A as per instructions of the site Engineer. Inspection: Site Engineer.

Supply and fixing of G.I. pipe perforated at a distance of 20 CM or less of required 25 length at culverts/ bridges/along the cuttings, suitably concreted at both ends as per drg. No. (NR/S&T/CON/1. 4/97) or at ASM office / other buildings suitably fixing it to the wall and at both ends. G.I. clamps of M.S. flats bolts and nut, to be supplied by the contractor. G.I. pipe 75/80 mm dia, 3mm thick. Inspection: RITES for supply, Site Engineer for execution.

Supply, laying & fixing of HDPE double Wall Corrugated (DWC) Duct as per as per RDSO Specification No. RDSO/SPN/204/2011 Ver. 1.1 With Amndt-1 (outer dia 120mm in 6m st. length with one coupler for every 6m length). All the materials cement, sand etc. are to be supplied by the 26 contractor. This includes brick work and other arrangements required to secure the pipe as per specifications, drawings and stipulations of tender documents and as per approved cable route plan including road crossing/platform/track crossing and for bridges and culverts etc. All the materials cement, sand & bitumen etc. are to be supplied by the contractor. Inspection: Supply- RITES, Installation- Site Incharge

All work of horizontal boring and trenchless cabling along with supply, transportation and insertion of double wall corrugated pipe -( ISI marked ) conforming to RDSO Spec no. 27 RDSO/SPN/204/2011, and the laying of cable in the boring under the track / road etc as per instruction of site engg. by using pipe of size 120 mm outer dia, 103.5 mm inner dia in which required No's of cables to be crossed. The depth of horizontal boring should be minimum 1.0 m from rail flange/road level. Inspection : RITES for DWC pipe.

"Laying of signalling/Telecom/power cables of different sizes as per approved Drg. No. NR/S&T/CON/1-1/97A and as per cable route plan approved by Railways and meggering of cable before and after its laying of all type of outdoor cables. Inspection: Site Engineer."

Supply of ARA Terminal Block 25MM center M6 terminal made of PBT as per IRS spec. No.IRS-S- 75/2006 (Rev.2) & IRS drawing No. SA- 23741A(Alt.4), SA23745(Alt.5), SA-23746 & SA- 23756(Alt.3). Inspection: RDSO

Supply of electric fuse complete with fuse block(base) for Railway signalling non- deteriorating type low voltage fuse assembly 2Amp/4Amp/16Amp. to suit. Specn. No.IRS: S- 78/2006 and fuse block made of PBT/Polycarbonate as per IRS: S-75/2006 (Rev-2 & Amd 2 ) and drg no. 23748 (IRS) Alt.4 or latest. Fuse block shall be suitable for round head type fuses. Inspection :RDSO

Supply of Portable digital auto range multi-meter clamp type Philips, Motwani, Fluke, 31 Rishabh make or similar capable to measure from (0.1mv/0.01ma) AC/DC upto 50Amp(AC/DC), 600V(AC/DC) and 0.1 ohms- 40M ohms suitable for measurement of Freq., capacitance complete with Manual, leads, battery and holster etc. Inspection :Consignee 32

Supply of manual track drilling machine. Inspection: Consignee

Relay, Non-AC Immunized, plug in type, style "QN1" DC neutral line 24VDC, 8F/8b 33 contact, front and back contact metal to carbon with plug board, retaining clip and connector a conforming to BRS:930,IRS - S - 34-68 Adm-6 and IRS:S-23/88-Adm-1 (as applicable). The interlocking code for this unit shall be ABCDF or latest. Inspection: RDSO

Supply of Relay, AC Immune, plug-in type, Style 'QNA1', DC Neutral Line, 24V contacts, front & back contacts metal to carbon with plug board retaining clip and connectors conforming to BRS 931A,IRS S 60,IRS S34 & IRS S23 (as applicable). Inspection RDSO

Supply fixing and wiring of fuse auto changeover system (FACS main system) as per RDSO/SPN/209/2012 Rev. 2.0 with latest amendments. One automatic changeover unit comprise 32 nos of external Non-Deteriorating Type or 'G' type fuses of various Ampere Rating, working voltage- 35 24 VDC which are in signalling circuits. System shall have 8 cards with monitoring arrangement of 4 fuses in one card. Installation, , wiring, Testing and commissioning of Fuse Alarm System, it consists of fixing of modules of fuse alarm system on existing relay rack, wiring from existing fuses to modules, soldering, lacing etc. working to be executed without affecting the functioning of the existing Circuits/Gears and the work shall be supplied by the contractor. Inspection by RDSO

Cleaning, Scrapping, Painting and lettering of all newly installed and existing gears such as signals, point equipment, track circuit equipment with T.C. no on rail app. Cases JB. TL JBs point rodding cranks, compensators etc. including gate equipment if existing in station section as per 36 the provision of IRSEM. All paints (ISI marked) shall be approved by Railway Engr. and painting material to be supplied by the contractor. This item also includes writing and painting requirement of all indoor and outdoor gears along with making of all circuit nos. near terminal and terminal boards/track in app. Cases, junction boxes, relay room, SMs room, writing of relay nomenclature fuse nos. and equipment nomenclature as the approved plans and as per provision of IRSEM. (1 Job=1 Station). Inspection: Site Engineer

Supply of ESM furniture of Godrej or better make consisting of the following :- 1. Executive revolving bearing series low back floating chair with normal arms cushioned Chair : 1No. 2. 37 Executive Table size 72x36x30" with 3 drawers one side, lockers cabinet on other side : 1No. 3. Visitor chair seat & back cushion with high density Foam with plastic PVC handle capsule type Flat pipe duly Painted black : 3Nos. 4. One Steel Almirah of size 48"x30"x17" with lock and handle arrangement for record keeping at station. Inspection : Consignee

General concrete work in cement, coarse sand and aggregate ratio 1:3:6, work 38 scattered at different places for items not covered in above schedule and fine plastering of top will be done with cement sand ratio of 1:4 . Volume of foundation also includes volume of C.I. base, anchor bolts etc. Coarse sand, aggregate 25mm and cement to be supplied by contractor. Inspection : Site Engineer

Supply and Installation of OFC integrated access device IPV6 ready 19" rack mountable for LVCD/Digital Axle Counter purpose with four tributary slots & front panel Quad indication status vide LEDs, Optical support vide 4 SFP port supporting TDMoIP /IPMPLS in the unit supporting dual core OFC and 04 100/1000mbps Ethernet port (POE or NON-POE as required at the site) for surveillance/smoke detector, optical SFP ports provided distance support to be 20 KMs, unit to support one E&M card supporting four2W/4W configurable & four quad port 2W/4W. Each port configurable to support axle counter/UFSBI/control phone/EC/RTU and one telnet/SNMP port, unit to support 04 E-1 ports in addition to 04SFP ports of TDMoIP/IPMPLS dual DC power supply 18 to 72VDC support, unit to support change over mechanism automatic between E&M (V.21) to E1 port & optical fiber TDMoIP (SFP) & quad path for E&M interface option, one number cable to be provided along with E&M. Equipment should be able to integrate with STM E1 & IPMPLS 1Gbps ports FABIO 2CX+/OFC/ DC& module 2W/4W four port E&M (1+1) protection, the unit to be able to integrate on 1Gbps with IPMPLS devices Make: TEAMENGG/FABIO or equivalent. Charges: Borne by Railways. Payment Terms:100% after supply. Inspection: RITES

Supply of VF Tapping & Termination Transformers 1120:470 Ohm as per IRS-TC-22/76 with Amd 1 with latest amendments. Inspection: Consignee

"Supply and installation of Fiber management syatem 19"" with all installation 41 materials, splicing, termination and testing of 2*24 fibre of the cable i.e. 48 fibre with all connector's material as per the instruction of the site engineer. Inspection:- For Supply Rites and for Installation : Site Engineer