Municipal Council Tender
If you're typing tender ID over and again or finding it difficult to go through the cumbersome government websites for looking at Delhi tenders online. We have come up with a solution i.e. we have collated every eprocurement Delhi tender on BidAssist. Also, for any queries related to an e-tender Delhi, like the bidding process, registration process, etc., the same are explained below.
Costs
EMD
₹ 41,264Document Cost
Refer DocumentsTender Fee
Refer Documents
Summary
Improvement To Swati Complex, New Delhi
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_NDMC_256189_1Bid Award Id
ViewTender No
33 /EE (BM-II)/2023-24Tender Authority
Municipal Council ViewPurchaser Address
-Website
http://https://www.ndmc.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Treatment at points of contact of wood work by chemical
emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.
305
85309
279.7
Spray painting using spray painting machine on M.S. Sheet, Cupboards Shutters/ Almirah of any size on both side in required colour/ Polish including necessary repair, denting, filling of putty, rubbing, primer and taking necessary precaution to avoid breakage of glass and using tape to avoid splashes on glass etc.complete as per direction of Engineer-in-charge. (Front face of almirah shall be measured with glass or without glass).
308
415911
1350.36
Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.
132
66884
506.7
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
32
76565
2392.65
Providing & Fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick
43
38584
897.3
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws
etc. complete :300x16 mm
18
5459
303.25
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm
18
2342
130.1
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm
18
1795
99.7
Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
Concrete of M20 grade with minimum cement content of 270 kg /cum
7
64488
9212.6
Providing and fixing brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 20 mm diameter.
353
121256
343.5
Providing and fixing Curtains of Décor/Welspun/Trident or equivalent complete arragement including stitching & fixing as per site requirement or approved by Engineer-in-charge. (Clean opening the Door/window to be measured).
1047
476636
455.24
P/F 1mm thick stainless steel (Grade-304) brush finished name plate signages of required size with side without having glossy border bend in deep photo etching. The required informatory matters, logo, picture etc filled with PU colour and polished border and fixing arrangement at the back using studs fasterners etc. as per direction of Engineer-In-Charge. (Surface area with bend shall be measured for payment).
31950
46328
1.45
Manufacturing, supplying and fixing retro reflective overhead signage as per drawings, specification and direction of the engineer-incharge.( Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01
as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete. Overhead informatory road signage
12
70559
5879.9
Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)
55
59986
1090.65
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets,gates and similar works
1416.96
244567
172.6
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
108
16837
155.9
Credit of dismantled material i) Old Curtain rod with pelmet
353
-10590
30
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements