Municipal Council Tender

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work (Excluding the cost of arcylic emulsion paint)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work(Excluding the cost of Synthetic enamel paint)

Supply and stacking of following materials of approved brand and manufacturer as per direction and entire satisfaction of engineer in charge at site including all lead. (a) White cement based Putty

(b) Water thinnble cement primer

(c) Arcylic Emulsion Paint

(d) Synthetic Enamel Paint

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 20 mm dia

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture1.4 mm in both directions with wire of dia 0.63 mm all complete. With 2nd class teak wood beading 62X19 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 15 mm nominal bore

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Fexible pipe (a) 32 mm dia.

(b) 40 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superiorglass (of approved quality) complete with 6 mm thick hard boardground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 15 mm dia CP Brass single/centre hole basin mixer for wash basin of approved quality and make per the direction and satisfaction of engineer in charge

Providing and fixing C.P. brass two way angle valve for basin mixer and geyser points of approved make and quality 15 mm nominal bore

Providing and fixing C.P. brass wall mixer non telephonic with chrome finish of approved make and quality as per the direction and satisfaction of engineer in charge

Providing and fixing Stainless Steel shower of Size 300 mm sqaure with 600 mm shower arm with flange of approved make and quality as per the direction and satisfaction of engineer in charge

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. 10 litre (full flush) capacity-white

Providing and fixing solid plastic seat with lid for pedestal type W.C pan complete : White solid plastic seat with lid

Providing and fixing SS connection pipe for hot and cold water at geyser or basin mixer points of approved quality as per the direction and satisfaction of engineer in charge 15 mm nominal bore 450 mm long with SS unions

Providing and fixing UV stabilised 2 mm thick plain FRP sheet by nuts and bolts or wire as per the direction and satisfaction of engineer in charge

Fabricating and fixing M.S. sheet cup board shutter with frame (factory made) Godrej style/design using 18 gauge M.S sheet in all work minimum width of chowkhat 100mm of required depth including cost of fixing with teak wood plugs of size 50x50x50 mm in C.C. 1:3:6 ( 1 cement 3 coarse sand :6 graded stone aggerdale 12.5 mm nominal size ) or with rawl plugs or with dash fasteners including locking arrangement with harrision / Plaza or equivalent make almirah lock and C.P. handle complete with appd. steel primer and spray painting in Teak or required colour finish as per direction of Engineer In Charge (only front face area of Almirah shall be measures for payment purpose).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :100 mm