Military Engineer Services Tender
If you're typing tender ID over and again or finding it difficult to go through the cumbersome government websites for looking at Delhi tenders online. We have come up with a solution i.e. we have collated every eprocurement Delhi tender on BidAssist. Also, for any queries related to an e-tender Delhi, like the bidding process, registration process, etc., the same are explained below.
Costs
EMD
₹ 97,110Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_680677_1Tender No
GE/SP/TOKEN-45/2024-25Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
M&L Reinforced cement concrete nominal mix 1:2:4, type B-1 using (using 20mm graded stoen aggregate) in slabs supported on walls, beams and column in floors,roofs,landings, balconies, canopies, deck slabs and in shelves and the like complete including formwork complete all as specified and directed by Engr-In-Charge.
1
-
-
Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed
15
-
-
Material and labour for false ceilings using GI snap grid system with roll-formed out of hot dip galvanised steel caping (powder coated) main runner 38 x 24 mm , cross Tee 29 x 24 mm and wall angle 24 x 24 mm members suspended with 4mm dia GI wire, carry maximum load up to 8.10 Kg/Sqm with 4mm thick designer ceiling board , pre painted Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions size 595 x 595mmx 4mm thick any texture (Lake and Hill, oceaniccascade or Electra) as approved by GE all as per , Everest Ceiling grid system 'Regular T-2430' or its equivalent make of "'Ramco, Charminar/Armstrong'' at any height complete all as specified and as directed by Engr-In-Charge.
15
-
-
M&L for rendering CM (1:6) 10 mm thick on fair faces of brick work or concrete surfaces etc including finished even and smooth without using extra cement complete all as specified and directed by Engr In Charge.
314
-
-
M&L for 15 mm thick cement plaster in cement mortar 1:4 on concrete or brick surface and finished even and smooth w/o using extra cement with water proofing compound complete all as specified and directed by Engineer-in-charge.
480
-
-
M & L rendering 5mm thick on ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and directed by Engr In Charge.
30
-
-
M&L for preparation of new plastered surfaces of walls, and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and directed by engr-in -charge.
154
-
-
M&L for Complete removal of existing treatment from walls and applying two coat of approved shade of oil emulsion distemper over a coat of alkali resistant primer complete all as specified and directed by Engr-in-Charge.
120
-
-
M&L for preparation of new plastered or unplastered surface and applying three coats of white wash on ceiling complete and all as specified and directed by engr-in -charge.
30
-
-
M & L for preparation of old plastered surface and applying two coats of white wash on ceiling complete and all as specified and directed by engr-in -charge.
50
-
-
Material & labour for preparation of new plastered surfaces and applying two coat of exterior grade modified antifungal water based weather proof acrylic emulsion dirt cleaning property paints on wall, fins, facias, chajjas over a coat of primer incl 3mm thick wall care putty etc complete all as specified and as directed by the Engr-in-Charge.
480
-
-
Material & labour for preparation of old decorated plastered surfaces and applying two coat of exterior grade modified antifungal water based weather proof acrylic emulsion dirt cleaning property paints on wall, fins, facias, chajjas incl 3mm thick wall care putty etc complete all as specified and as directed by the Engr-in-Charge.
450
-
-
Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area exc 1.5 sqm and not n.exc 4.0 sqm (including make good with CM 1:4 and hold fast) complete all as specified and directed by Engr In Charge.
6
-
-
All as per item No 16 here in before area not exc 1.5 Sqm .
3
-
-
Taking down shutters of any description exc 1.0 sqm but not exc 2.0 sqm each complete all as specified and directed by Engr In Charge.
6
-
-
S&F for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165. complete all as specified and directed.
496
-
-
S&F windows/ventilators section of frame 72 X 55 fixed to wall or concrete surface with ms hold fast (30 x 5 section) 150 mm long made of galvanised steel powder coated and section of shutter 47 X 20 mm mulion section 72 X 50 mm (Base steel as per IS 513 "D" quality galvanised as per IS 277 with zinc of 120 gms/ Sqm ) glazed or guaged and wire guage shutter prepare to recieve wire mess to the shutters ( Double door shutter) with total coated thickness of 0.60 mm including powder coated grill/guard bars made of surface bars 10 mm dia at 100 c/c horizontal spacing fixed in ms flat frame ( 30 x 5 mm ) fixed to windwods frames with screws incl 4 to 5 mm thick sheet glass, 0.36 mm stainless steel wire cloth with 1.40 mm aparture neccessary fittings and all builders hard ware such as handles ,tower bolts, and stays and cooler opening shall be provided with double side shutter with grill and design of window shall be approved by Engr-in-Charge etc. complete all as specified and shown in Drg No : CEAF/STD-191/2014 Sheet No 1/2 and 2/2 dated 11-12-2014 including taking down existing window/vetilator and making good complete all as specified and directed
12
-
-
M & L for cement concrete type C1, 1:3:6 (using 12.5 mm graded stone aggregate) in door and windows frames, any size, single or double rebated, including ar- rangement for fixing of hinges and fixtures as required complete all as specified and directed by Engr In Charge.
0.1
-
-
S & F 35mm thick factory made plain framed, Flush shutters, solid core construction, with block board core and plywood face panels, commercial particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engr In Charge.
15
-
-
Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification complete all as specified and directed by Engr In Charge.
14
-
-
S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face complete all as specified and directed by Engr In Charge.
4.7
-
-
S&F 150mm long Aluminium anodised, barrel tower bolts of ex- truded section and fixed complete all as specified and directed by engr-in -charge.
15
-
-
S&F 150mm long aluminium handle cast type polished bright complete all as specified and directed by engr-in -charge.
24
-
-
S&F 100 mm long butt hinges medium weight, stenless steel, and fixed complete and specified and directed by engr-in -charge.
36
-
-
S&F for 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed by engr-in -charge.
9
-
-
Demolition of concrete surfaces in ground floor and paving n.exc. 15cm thickness (below or above ground level) complete all as Specified and directed
6.75
-
-
M & L for 75 mm thick PCC 1:3:6 type C2 as in Plinth Protection (using 40 mm graded stone aggregate) including making joints & filling with sand bitumen mastic complete all as specified and directed by Engr In Charge.
90
-
-
Dismantling stone slab and granite of any description or thickness in floors etc and removing the debries outside the MOD land complete all as specified and directed by Engineer-in-Charge.
40.4
-
-
M & L 15 mm thick screed bed or bedding layer of cement mortar (1:4), for laying of granite complete all as specified and directed by Engr In Charge.
8
-
-
M&L 20mm thick Granite (of any type) work (table rubbed and polished) in flooring, steps, jambs, pillars, window cills, cooking platform, wall and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with add mixture of pigment to match with shade of granite complete all as specified and directed
64
-
-
M&L Machine cut pre polished kota stone flooring 20 mm(+-2mm) thick in tread of steps,Floor and similar over cement screed 20 mm thick in cm 1;4 base laid and jointed with grey slurry mixed with pigment to match the slab including rubbing and polishing complete all as specified and directed by Engr In Charge.
42
-
-
Supply only liquid water proofing compound complete all as specified and directed.
6
-
-
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed by Engr In Charge.
656
-
-
M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed by Engr In Charge.
210
-
-
All as per item No-37 here in before but as on vertical surface of wall such as skirting/dado incl 10mm thick cement plaster (1:4) as in backing coat of tiles
18
-
-
M&L Glazed ceramic coloured tiles in vertical surface 300X 450X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl back plaster 10 mm thick in cm 1:4 complete all as specified and directed by Engr In Charge.
328
-
-
M & L for providing cement concrete 1:2:4 type B-0 cement concrete (using 12.5mm graded aggregate) as in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed by engr-in -charge.
0.5
-
-
M&L for Preparation of old/New painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge.
35
-
-
M&L for Preparation of new wooden surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr In Charge.
14
-
-
M&L for one coats of synthetic enamel paint including preparation of old wooden surfaces complete all as specified and directed by Engr In Charge.
10
-
-
Taking down steel tubing or removing from site of 15mm bore pipe complete all as specified and directed by Engineer-in-charge.
30
-
-
All as per item No 44 here in before but 20mm bore.
40
-
-
S&F for 15mm bore steel water tubing medium grade , galvanized ISI marked with all fittings fixed to wall & ceiling or laid in floors complete all as specified and directed by Engineer-in-charge.
30
-
-
All as per item No 46 here in before but 20mm bore
40
-
-
Dismantling water tanks exc 250 but not exc 500 ltrs capacity and removing to store complete all as specified and directed by Engr In Charge.
3
-
-
S&F Rotational moulded polyethylene 500 Ltr water storage tanks as per IS (cylindrical vertical with closed top) hoisted and fixed in position including necessary fittings complete all as specified and as directed by Engr-in-Charge.
3
-
-
S &F for 20 mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass errule and fixed complete all as specified and directed by Engr In Charge.
3
-
-
S&F in repairs vitreous china wash down water closet pan (Pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) incl P or S trap etc complete all as specified and directed by Engineer-in-charge.
3
-
-
S&F in repairs10 ltr capacity PVC flushing cistern coloured with accessories Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete and specified and directed by engr-in -charge.
3
-
-
S&F in repair 600mmx450mm bevelled edge mirror of selected quality 5mm glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engr In Charge.
3
-
-
S & F in repairs for 125mm dia stainless steel grating doom with or without waste hole for waste pipe ( minimum weight 40 gram) complete all as specified and directed by Engr In Charge.
6
-
-
S&F as in repairs 15 mm Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated with long shank and cup (concealed type) complete all as specified and directed.
10
-
-
S & F as in repairs 15mm CP bib tap fancy type copper alloy with crutch or butterfly handle , screwed down, screwed for iron pipe etc complete all as specified and directed by Engr In Charge.
6
-
-
M&L as in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed by Engr In Charge.
4
-
-
S&F in repairs vitreous china wash hand basin of size 550mm x 400mm white, flat back including angle iron brackets with two coats of synthetic enamel paints including PVC waste pipe of 32mm dia of suitable length, CP fancy type pillar cock, PVC connection of 15mm dia & 450mm long with PTMT nuts, and 32mm dia brass waste fitting complete all as specified and directed.
3
-
-
S&F 15mm dia PVC Connection 450 mm long with nuts complete all as specified and directed by Engr In Charge.
8
-
-
Taking out of APP modified water proofing membrane including mud puska complete on roof surface and surface properly cleaned by wire brush including removing of debries/domolished material from roof out from defence land complete all as specified and as directed by Engineer-in-Charge.
430
-
-
M&L for preparation of plastered/concrete surfaces of roof and applying the under mentioned course of roof treatement complete all as specified and directed by Engineer-in-Charge.:-
(a) Surface shall be throughly wire brushed, cleaned, washed, dried up properly and apply evenly a bituminuous primer coat conforming to IS @0.4 ltr /Sqm over concrete / plastered roof surface.
(b) Applying evenly a tack coat of bitumen 85/25 grade @1.20 kg/ sqm.
(c) Laying of 3mm thick APP membrane sheet (min weight 3 Kg/Sqm) consisting of a core of 160 gms/Sqm polyster non woven fabric mat protected on both sides with a high quality polymeric asphaltic mix again protected with thermo fusible HMHDPE FILM on dried primed surface by torch application method. APP membrane will normally be laid in length at right angle to the direction of slope. The over lap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc.
(d) Membrane bonded completely to the substrate & the over laps are then scaled/fused by flame.
(e) Including 10mm thick rendering with 1:4 using WPC.
(f) Painting with two coats of water proofing paint with aluminium finish. (g) PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) roof kerbs, benching rounded or chamfered on edge including rounded or chamfered edges with necessary form work etc complete
Note:- This treatement shall be done by the approved authorized applicators and guarantte of treatement shall be for 10 years.
430
-
-
M&L PCC 1:2:4 type B1 (using 20mm graded stone aggregate) mixed with water proofing compound as per manufacturer instructions laid as in padding over roof slabs for providing proper slope to the concrete padding, surface finished even and smooth without using extra cement up to four stories complete all as specified and directed
10.75
-
-
Dismantling of corrugated steel sheeting any gauge, thickeness including nainital or similar roof coverings complete all as specified and as directed.
250
-
-
S & F moulded pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed
230
-
-
S&F precast machine pressed PCC interlocking paver block of 80 mm thickness, M-40 grade of any shape and size confirming to IS -15658-2006 with grey cement and pigment as approved over 50mm thick sand cushion and 100mm thick plain cement concrete, type D-2, 1:4:8, (using 40mm graded stone aggregate) as in sub base flooring, surface finished even and rough to receive floor topping including dismentling complete all as specified and directed by Engineer-in-Charge.
288
-
-
S&F in repairs Brass CP tubular Towel rail , 20 mm dia, D Type 600mm long between flanges brass chromium plated with screws and cleats, (Minimum weight 190 gms) complete all as specified and directed by Engr In Charge.
2
-
-
S&F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws as specification complete all as specified and directed by Engr In Charge.
20
-
-
S&F steel/work in tubular truses, purlins, rafters, struts, vertical members and similar work including special shape washers complete using ERW or induction butt welded tubes confirming to I.S. 1161-1998 grade St-240 as specification complete all as specified and directed by Engr In Charge.
2700
-
-
M&L for excavation in post holes ( or similar holes) in any type of soil each n.exc. 0.5 cum, getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm complete all as specified and directed by engr in charge
18
-
-
M&L for applying two coats of synthetic enamel paint on steel & iron surfaces of any description , not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of red oxide, zinc chrome complete all as directed by engr in charge
110
-
-
Demolition of cement concrete un reinforced in ground floors and Pavings exc 15 cm thick but not exc 60 cm thick (below ground level ) complete all as specified and directed
2.5
-
-
M&L for providing reinforced cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) in precast posts, fencing posts, struts etc, for fencing, average sectional area exc 250 Sq. cm and n.exc 400 Sq. Cm , with or without chamfered angles and flat, splayed, rounded or mitred tops complete all as specified and directed by Engr In Charge
4.5
-
-
M&L Brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed by Engr In Charge.
17
-
-
M&L Precast cement concrete1:2:4 type B-1 (using 20 mm graded stone aggregate) as in coping, benching etc including necessary form work, chamfers, weatherings, throating etc. Complete all as specified and directed.
0.2
-
-
Taking down cement plaster etc on brick wall or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and disposed off unserviceable materials to out side MOD land complete all as specified and directed by Engineer-in-Charge.
849
-
-
M&L for rendering CM (1:6) 15 mm thick on other than fair faces of brick work or concrete new /old surfaces etc including finished even and smooth without using extra cement complete all as specified and directed by Engr In Charge.
245
-
-
M&L for preparation of newly plastered or unplastered surface and applying two coats of distemper oil emulsion on walls over a coat of primer incl 1.5mm thick wall care putty on walls complete all as specified and directed by Engr-In-Charge.
160
-
-
M&L for preparing surfaces of new plaster Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and directed by Engineer-in-charge.
245
-
-
M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not xceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:4) over 100mm thick plain cement concrete, type D-2, 1:4:8, complete all as specified and directed by Engr In Charge.
100
-
-
S&F precast machine pressed PCC interlocking paver block of 80 mm thickness, M-40 grade of any shape and size confirming to IS -15658-2006 with grey cement and pigment as approved over 50 mm thick sand cushion and 100mm thick plain cement concrete, type D-2, 1:4:8, (using 40mm graded stone aggregate) as in sub base flooring, surface finished even and rough to receive floor topping including dismentling complete all as specified and directed.
765
-
-
M&L for Chequered cement concrete tiles (rubber moulded with gloshy finishing) with grey cemet and pigments 30cm x30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with 15mm thick bedding layer of cement sand mortar (1:6) including dismentling complete all as specified and directed by Engr In Charge.
30
-
-
M&L for machine pressed precast cement concrete factory made glazed kerb stone of any size PCC (1:2:4) type B 0 using 12.5 mm graded stone agg , jointed in CM 1:4 including excavation and removing complete all as specified as directed.
8
-
-
M&L for two coats of synthetic enamel paint over a coat of priming paint incl preparation of concrete surface old or new exc 10 cm width or girth complete all as specified and as directed by engr in charge.
180
-
-
Taking down carefully copper/aluminium point wiring light ,fan, light fittings,socket or power complete, such as switches, ceiling roses, pendents, regulators, sockets etc.removing materials to store for keeping in safe costudy or for taking credit (credit for above items should be made as per conditioned separately) and making good disturbed surface of walls, floors etc. complete all as specified and directed by Engineer-in-Charge.
70
-
-
M&L for point wiring for one light point controlled by one SP switch with single core PVC insulated unsheathed 1100 volt grade cable with multi strand copper conductor of size 1.5 Sq mm FRLS (Nominal area) drawn through and including non metallic rigid PVC concealed conduit, medium grade, ISI marked not less than 20mm dia, concealed in wall, ceiling with GI saddles GI screws, rawl plugs (concealed conduit wiring) with all fittings including Tee, Junction boxes and provision of pressed steel terminal modular box powder coated of suitable size for mounting switch sockets and regulators and drawing continuous earth wire of PVC insulated unsheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) complete all as specified.
Note: Cost for cutting, chasing and making good to existing surfaces are deemed to be included in the Quoted Rate.
28
-
-
All as per item No 85 here in before but for one fan/exhaust fan point controlled by one SP switch.
10
-
-
All as per item No-85 here in before but for one 3 pin socket out let, 6 Amps on same board with the cable 1.5 Sqmm size.
8
-
-
All as per item No-85 here iin before but for one 3 pin socket out let, 6 Amps on Independent board with the cable 1.5 Sqmm size.
12
-
-
All as per item No 85 here in before but with 2.5 Sq mm cable for Independent bd one 3 pin 15 Amps socket outlet including S/C 2.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR LS cable for continuous earth wire required size all as specified and directed by Engineer-in-Charge.
12
-
-
S&F switch piano 5 amps flush type single pole one way suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.
58
-
-
S&F socket outlet flush type 5 pin 6 amps suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.
20
-
-
S&F switch piano 16 amps flush type single pole one way suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.
12
-
-
S&F socket outlet 2 in 1, 5 pin 16 amps flush type suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.
12
-
-
Supply and fix electronic Fan Regulator rotary flush step type 120 watt, 240 volt complete all as specified and directed.
5
-
-
Supply and fixing of ceiling roses, surface bakelite 65x50mm 2 or 3 terminals , PVC/Polycarbonate, isolated body fixed on PVC round block complete all as specified and directed by Engineer-In- Charge.
22
-
-
Supply and fixed Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB complete all as specified and directed.
2
-
-
Supply and fixing wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver ,20 watt LED fitting, 4000K , 230 Volts, diffused optics ,etc complete with all accessories , connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting, and testing complete all as specified and directed by the Engineer- In- Charge.
26
-
-
Supply and fixing wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver ,10 watt LED fitting with 100 lumen/watt, 6000K , 230 Volts, diffused optics ,etc complete with all accessories , connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting, and testing complete all as specified and directed by the Engineer- In- Charge.
2
-
-
Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up driver with flexible copper conductor cases of suitable size complete all as specified and directed.
2
-
-
Supply and fixing LED security light fitting 35 watt high pressure dia cast aluminium housing and secondary optical lens for superior light distribution , heat resistant thoughened glass with frame, IP66 protection complete with lamp & connected item and connection with suitable cable from ceiling rose to light fitting and fixing on GI bracket made out of suaitable GI Pipe medium garde 1.2 mtr long bent to shape and fixed on wall with flat iron clamps, nuts bolts washer etc complete all as specified and directed
3
-
-
Taking down including disconnecting the electric connection of ceiling fan dismantling blades and greasing complete all as specified and directed
5
-
-
Hanging / fixing only ceiling fan received from item No 101 above and connecting up including fastner and provision of suitable size of copper cable from connector of fans to ceiling rose complete all as specified and directed.
5
-
-
Taking down including disconnecting the electric connection of exhaust fan, dismantling blades,greasing and painting the whole assembly including marking MES No complete all as specified and directed
2
-
-
Fixing only Exhaust fan received from item No 103 above and connecting up including fastner and provision of suitable size of copper cable from connector of fans to ceiling rose complete all as specified and directed.
2
-
-
Taking down unserviceable submain wiring of alluminium two runs of any size cable including batten/conduit complete etc and making good disturbed surfaces complete all as specified and directed.
120
-
-
M & L for in replacement submain wiring with two run of 6.0 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked and one run of 6.0 sqmm PVC insulated but unsheathed FRLS cable for earth continuty conductor drawn through and under suitable size of rigid non metallic PVC conduit , medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all laid/fixed concealed in wall/ceiling or surface in wall and surface conduit on ceiling, and also include the specified runs of specified size earth continuity conductor of similar type cable complete all as specified. Note - 2 Runs of 6.0 Sqmm single core and one run of 6.0 sqmm single core cable with one run of 20mm dia PVC conduit shall be measured as one unit for payment purpose
50
-
-
M & L for in replacement submain wiring with two run of 4.0 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked and one run of 4.0 sqmm PVC insulated but unsheathed FRLS cable for earth continuty conductordrawn through and under suitable size of rigid non metallic PVC conduit , medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all laid/fixed concealed in wall/ceiling or surface in wall and surface conduit on ceiling, and also include the specified runs of specified size earth continuity conductor of similar type cable complete all as specified. Note : 2 Runs of 4.0 Sqmm single core and one run of 4.0 sqmm single core cable with one run of 20mm dia PVC conduit shall be measured as one unit for payment purpose
70
-
-
Taking down old MCB DB SPN with MCBs of any size from site complete all as specified and directed.
4
-
-
Supply and fixing in replacement MCB distribution board with Bus bar 200A neutral link , earth bar made out of CRCA mild steel sheet surface mounting SPN 8 way 230 volts double door type regal gray horizontal type complete all as specified and as directed by Engineer-in-Charge. Note :- MCB shall be measured and paid seperately.
2
-
-
Supply and fixing in replacement MCB distribution board with Bus bar 200A neutral link , earth bar made out of CRCA mild steel sheet surface mounting SPN 12 way 230 volts double door type regal gray horizontal type complete all as specified and as directed by Engineer-in-Charge. Note :- MCB shall be measured and paid seperately.
2
-
-
S&F MCB SP 6 to 32 Amps 10 KA, 240 volt 'C' Series complete all as specified and directed by engineer-in-charge.
32
-
-
S&F MCB SPN 40 Amps 10 KA, 240 volt 50 Hz 'C' Series complete all as specified and directed by engineer-in-charge.
4
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%