Military Engineer Services Tender

M&L for river washed and screened, dry sand filling in trenches for cushioning of UG cables as layers of 8 cm before laying and 15 cm after laying of cables complete all as specified and directed by Engineer- in- Charge. Note : Measurement shall be taken after punning down.

S&F of sub class B bricks having minimum compressive strength 75 Kg/ Sqcm laid in trenches for cable protection etc complete all as specified and directed by Engineer- in- Charge.

All as per srl item No 5 here-in-before but using old bricks obtained under srl item No 1 complete all as specified and directed by Engineer- in- Charge.

Supply, laying, jointing, testing and commissioning in replacment of LT underground cables 1100 volts grade, PVC insulated XLPE and PVC sheathed, heavy duty armoured, with multistranded aluminium conductors, IS-1554 marked, laid in trenches complete all as specified and directed by Engineer- in- Charge. Cables of the following sizes:- Note Excavation, earth work, cable protection, sand fillings, cable joint shall be measured and paid separately.

35 Sq mm 3.5 core.

50 Sq mm 3.5 core.

70 Sq mm 3.5 core.

95 Sq mm 3.5 core.

185 Sq mm 3.5 core.

S&F of 90 Watt LED street light fittings made up of pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, IP66 protection complete all as specified and directed by Engineer- in- Charge.

M&L for GI Tubes of size 50 mm dia light grade, galvanised, with all fitting, laid in trenches for protection of cable in road /drain crossing complete all as specified and directed by Engineer- in- Charge.

M&L for boring of holes under road, pavement, hard standing by trenchless technology including 150 mm dia HDPE pipe suitable for 0.6 mpa working pressure. Note :- The quoted rate shall deemed to be included of taking permission from concerned authority like Army Signal and other utility authority and any damage done during execution of work and the same will be repaired/replaced by the Contractor.

Taking out old rusted unserviceable LT panel Supply, installing, testing and commissioning in replacement outdoor type stainless steel (SS 316) cubical enclosure compartmentalized exterior and interior mirror type brushed suitable for highly corrosive environment, high creep resistance, better mechanical properties like ductility, yield strength, hardness etc. The outer enclosure shall be made of 3.15 mm thick SS 316 sheet and inner compartment should be 2 mm. The fixing of double doors shall be on SS hinges with anti-theft provision (the door can’t be removed from enclosure without cutting enclosure). All fabrication/welding shall be done with TIG/MIG or as approved by Engineer in charge suitable for SS 316. Sliding handle and locking arrangement front and rear both side. Enclosure shall be suitable for AC supply system 415 volts, 3 phase, 4 wire, 50 Hz. IP-55 class protection and mounted on channel 75 mm welded with panel of SS 316 with 04 Nos foundation bolt of size not less than 20mm dia and 300mm long. The enclosure shall have provision of cable alley. Cable entry from bottom side including internal wiring with PVC insulated solid, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size (but not less than 2.5 sqmm) and comprising of the following :- INCOMING :- (i) MCCB 4 pole , 400 Amps,50 Hz,415 Volts, 50 KA, with adjustable thermal & fixed Magnetic type - 01 Nos (ii) Onload changeover 400 Amps -01 No (iii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No (iv) Ammeter digital type with 4 way rotary selector switch-01No (iv) CTs ratio 400/5 A ,class 1, ISI marked -01 set of three (v) Indicating lamp- 01 set of three (vi) Aluminium bus bar of rating 600A - set of four (vii) Rotary handle - 02 No. OUTGOING :- (i) MCCB 4 pole , 125 Amps,50 Hz,415 Volts, 35 KA with adjustable thermal & fixed Magnetic type - 03 Nos. (ii) MCCB 4 pole , 100 Amps,50 Hz,415 Volts, 35 KA with adjustable thermal & fixed Magnetic

type - 03 Nos. (iii) Rotary handle - 06 Nos PLATFORM FOR PANEL :- Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level. Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947/IS 13947/Pt.II/1993 (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer. (iv) Energy meter is not included in the present scope of work and shall be shifted from Old LT Panel to New LT Panel. The rate for shifting is also deemed to be included in the quoted rates.

All as per item No. 11 here-in-before but comprising of the following :- (Near 17 Mandir Marg) INCOMING :- (i) MCCB 4 pole , 400 Amps,50 Hz,415 Volts, 50 KA, with adjustable thermal & fixed Magnetic type - 01 Nos (ii) Onload changeover 400 Amps -01 No (iii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No (iv) Ammeter digital type with 4 way rotary selector switch-01No (iv) CTs ratio 400/5 A ,class 1, ISI marked -01 set of three (v) Indicating lamp- 01 set of three (vi) Aluminium bus bar of rating 600A - set of four (vii) Rotary handle - 02 Nos OUTGOING :- (i) MCCB 4 pole , 200 Amps,50 Hz,415 Volts, 35 KA with adjustable thermal & fixed Magnetic type - 01 Nos. (ii) MCCB 4 pole , 160 Amps,50 Hz,415 Volts, 35 KA with adjustable thermal & fixed Magnetic type - 02 Nos. (iii) MCCB 4 pole , 125 Amps,50 Hz,415 Volts, 35 KA with adjustable thermal & fixed Magnetic type - 03 Nos. (iv) MCCB 4 pole , 100 Amps,50 Hz,415 Volts, 35 KA with adjustable thermal & fixed Magnetic type - 03 Nos. (v) Rotary handle - 09 No PLATFORM FOR PANEL :- Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level.

Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947/IS 13947/Pt.II/1993 (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer. (iv) Energy meter is not included in the present scope of work and shall be shifted from Old LT Panel to New LT Panel. The rate for shifting is also deemed to be included in the quoted rates.

All as per item No. 11 here-in-before but comprising of the following :- INCOMING :- (i) ACB 4 pole, 1000 Amp, 415 Volts, 50 KA - 01 No (ii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No (iii) Ammeter digital type with 4 way rotary selector switch-01No (iv) CTs ratio 1000/5 A ,class 1, ISI marked -01 set of three (v) Indicating lamp- 01 set of three (vi) Aluminium bus bar of rating 1600A - set of four OUTGOING :- (i) MCCB 4 pole, 250 Amps, 50 Hz, 415 Volts, 35 KA with adjustable thermal & fixed Magnetic type - 04 Nos. (ii) Rotary handle - 04 Nos PLATFORM FOR PANEL :- Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level. Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947/IS 13947/Pt.II/1993 (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer. (iv) Energy meter is not included in the present scope of work and shall be shifted from Old LT Panel to New LT Panel. The rate for shifting is also deemed to be included in the quoted rates.

Supply, installation, testing and commissioning in replacement of factory made and tested (including CPRI type tested certified panel) LT Panel board ,cubical compartmentalized , out door type double door , plate form mounted, suitable for 415 volts, 3 phase, 4 wire, 50 HZ AC supply system having bus bar chamber with insulated aluminium bus bars four pole installed on porcelain/SMC insulator. The panel shall be dust and vermin proof. IP-65 class protection and shell be made of 3.15 mm CRCA MS sheet, and 50x50x6mm thick MS angle iron frame work, powder coated finish over one coat of red oxide primer on outside surface and painted inside with two coats of red oxide primer, front and rear opening type, with apron for cable entry closing locking arrangement including internal wiring with PVC insulated solid, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size (but not less than 2.5 Sqmm) and comprising of the following :- (Mall Road) INCOMING :- (i) ACB 4 pole, 800 Amp, 50 KA, 415 Volt AC Horizontal draw out type motorized, front operated with Micro processor based LCD protection release for adjustable over current, short circuit and earth fault protection-01 No (ii) Voltmeter digital type with 4 way rotary selector swicth -01 No. (iii) Ammeter digital type with 4 way rotary selector switch-01 No. (iv) CTs ratio 800/5 A ,class 1, ISI marked -01 sets of three (v) Indicating lamp- 01 set of three (vi) Aluminium bus bar of rating 1600 Amp- set of four OUTGOING :- (i) MCCB 4 pole , 400 Amps,50 Hz,415 Volts, 36 KA with microprocessor release - 03 Nos. (ii) MCCB 4 pole , 200 Amps,50 Hz,415 Volts, 36 KA with microprocessor release - 02 Nos. (iii) Rotary handle - 05 No PLATFORM FOR PANEL :- Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The

platform shall be such that it is of a height 45 cm above the nearest road level. Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947-II/IS 13947-II (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer.

All as per item No.11 here-in-before but comprising of the following :- (Near Mall Road circle) INCOMING :- (i) MCCB 4 pole, 400 Amps, 50 Hz,415 Volts, 50 KA, with adjustable thermal & fixed Magnetic type - 01 Nos (ii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth - 01No (iii) Ammeter digital type with 4 way rotary selector switch - 01No (iv) CTs ratio 400/5 A ,class 1, ISI marked -01 sets of three (v) Indicating lamp- 01 set of three (vi) Aluminium bus bar of rating 600A - set of four (vii) Rotary handle - 01 No OUTGOING :- (i) MCCB 4 pole, 315 Amps,50 Hz,415 Volts, 35 KA with adjustable thermal & fixed Magnetic type - 01 No. (ii) MCCB 4 pole, 200 Amps,50 Hz,415 Volts, 35 KA with adjustable thermal & fixed Magnetic type - 02 Nos. (iii) MCCB 4 pole, 125 Amps,50 Hz,415 Volts, 35 KA with adjustable thermal & fixed Magnetic type - 02 Nos. (iv) Rotary handle - 05 Nos PLATFORM FOR PANEL :- Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level.

Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947/IS 13947/Pt.II/1993 (Latest Version). The MCCB should have Ics=100%Icu. The MCCBsshall have spreader links and barriers as standard feature of manufacturer . (iv) Energy meter is not included in the present scope of work and shall be shifted from Old LT Panel to New LT Panel. The rate for shifting is also deemed to be included in the quoted rates.

All as per item No. 14 here-in-before but comprising of the following :- (Near 16 Mall road) INCOMING :- (i) MCCB 4 pole, 400 Amps,50 Hz,415 Volts, 50 KA, with adjustable thermal & fixed Magnetic type - 01 Nos (ii) Onload changeover 400 Amps -01 No (iii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No (iv) Ammeter digital type with 4 way rotary selector switch-01No (iv) CTs ratio 400/5 A ,class 1, ISI marked -01 sets of three (v) Indicating lamp- 01 set of three (vi) Aluminium bus bar of rating 600A - set of four (vii) Rotary handle - 02 No OUTGOING :- (i) MCCB 4 pole , 160 Amps,50 Hz,415 Volts, 35 KA with thermal magnetic release - 02 Nos. (ii) MCCB 4 pole , 125 Amps,50 Hz,415 Volts, 35 KA with thermal magnetic release - 04 Nos. (iii) MCCB 4 pole , 100 Amps,50 Hz,415 Volts, 35 KA with thermal magnetic release - 04 Nos. (iv) Rotary handle - 10 No PLATFORM FOR PANEL :- Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level. Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947/IS 13947/Pt.II/1993 (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer.

(iv) Energy meter is not included in the present scope of work and shall be shifted from Old LT Panel to New LT Panel. The rate for shifting is also deemed to be included in the quoted rates.

Supply, installing, testing and commissioning of factory made and tested (including CPRI type tested certified timer panel) LT Panel board ,cubical compartmentalized , out door type double door , plate form mounted, suitable for 415 volts, 3 phase, 4 wire, 50 HZ AC supply system having bus bar chamber with insulated aluminium bus bars four pole installed on porcelain/SMC insulator. The panel shall be dust and vermin proof. IP-65 class protection and shell be made of 3.15 mm CRCA MS sheet, and 50x50x6mm thick MS angle iron frame work, powder coated finish over one coat of red oxide primer on outside surface and painted inside with two coats of red oxide primer, front and rear opening type, with apron for cable entry closing locking arrangement including internal wiring with PVC insulated solid, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size ( but not less than 2.5 Sqmm) and comprising of the following :- (DID LINE PARK) INCOMING :- (i) MCCB 4 pole , 125 Amps,50 Hz,415 Volts, 25 KA with Adjustable thermal and fixed magnetic type - 01 Nos (ii) 3 Pole power contractor, type MNX 110 having 2 NO +2 NC -01 No (iii) Electromechanical class time switch day programme with resume- 1 Nos (iv) Auto /manual selector switch -01 No (iv) Voltmeter digital type with 4 way rotary selector swicth -01No (v) Ammeter digital type with 4 way rotary selector switch-01No (vi) CTs ratio 125/5 A ,class 1, ISI marked -01 sets of three (vii) Indicating lamp- 01 set of three (viii) Aluminium bus bar of rating 250 Amp- set of four OUTGOING:- (i) MCCB 4 pole , 63 Amps,50 Hz,415 Volts, 25 KA with Adjustable thermal and fixed magnetic type - 03 Nos

PLATFORM FOR PANEL :- Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, typeC-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level.

All as in item No 14 here-in-before but comprising of the following:- (Near Gate No:- 03 and HRC ) INCOMING :- (i) MCCB 4 pole , 250 Amps,50 Hz,415 Volts, 50 KA, with Adjustable thermal and fixed magnetic type - 01 Nos (ii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No (iii) Ammeter digital type with 4 way rotary selector switch-01No (iv) CTs ratio 250/5 A ,class 1, ISI marked -01 sets of three (v) Indicating lamp- 01 set of three (vi) Aluminium bus bar of rating 400A - set of four (vii) Rotary handle - 01 No OUTGOING:- (i) MCCB 4 pole , 100 Amps,50 Hz,415 Volts, 35 KA with Adjustable thermal and fixed magnetic type - 02 Nos. (ii) MCCB 4 pole , 125 Amps,50 Hz,415 Volts, 35 KA with Adjustable thermal and fixed magnetic type - 03 Nos. (iii) Rotary handle - 05 No PLATFORM FOR PANEL :- Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level. Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947/IS 13947/Pt.II/1993 (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer.

(iv) Energy meter is not included in the present scope of work and shall be shifted from Old LT Panel to New LT Panel. The rate for shifting is also deemed to be included in the quoted rates.

Supply, installing, testing and commissioning in replacement of factory made and tested (including CPRI type tested certified panel) LT Panel board ,cubical compartmentalized , out door type double door , plate form mounted, suitable for 415 volts, 3 phase, 4 wire, 50 HZ AC supply system having bus bar chamber with insulated aluminium bus bars four pole installed on porcelain/SMC insulator. The panel shall be dust and vermin proof. IP-65 class protection and shell be made of 3.15 mm CRCA MS sheet, and 50x50x6mm thick MS angle iron frame work, powder coated finish over one coat of red oxide primer on outside surface and painted inside with two coats of red oxide primer, front and rear opening type, with apron for cable entry closing locking arrangement including internal wiring with PVC insulated solid, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size ( but not less than 2.5 Sqmm) and comprising of the following :- INCOMING :- (i) MCCB 4 pole , 400 Amps,50 Hz,415 Volts, 50 KA, with Adjustable thermal and fixed magnetic type - 01 Nos (ii) Voltmeter 0-500 volts digital type with 4 way rotary selector swicth -01No (iii) Ammeter digital type with 4 way rotary selector switch-01No (iv) CTs ratio 400/5 A ,class 1, ISI marked -01 sets of three (v) Indicating lamp- 01 set of three (vi) Aluminium bus bar of rating 600A - set of four (vii) Rotary handle - 01 No OUTGOING :- (i) MCCB 4 pole , 250 Amps,50 Hz,415 Volts, 35 KA with Adjustable thermal and fixed magnetic type - 01 Nos. (ii) MCCB 4 pole , 200 Amps,50 Hz,415 Volts, 35 KA with Adjustable thermal and fixed magnetic type - 02 Nos. (iii) MCCB 4 pole ,125 Amps,50 Hz,415 Volts, 35 KA with Adjustable thermal and fixed magnetic type - 01 Nos. (iv) Rotary handle - 06 No

PLATFORM FOR PANEL :- Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level. Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947/IS 13947/Pt.II/1993 (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer . (iv) Energy meter is not included in the present scope of work and shall be shifted from Old LT Panel to New LT Panel. The rate for shifting is also deemed to be included in the quoted rates.

Note : Contractor should procure and provide 50 % of the material as listed above within 15 days of the placing of work order and shall be verified by the Engr-in-charge.