Military Engineer Services Tender
If you're typing tender ID over and again or finding it difficult to go through the cumbersome government websites for looking at Delhi tenders online. We have come up with a solution i.e. we have collated every eprocurement Delhi tender on BidAssist. Also, for any queries related to an e-tender Delhi, like the bidding process, registration process, etc., the same are explained below.
Costs
EMD
₹ 4,79,000Document Cost
₹ 2,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_682751_1Tender No
CEDZ/TOKEN-21 OF 2024Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Dismantling boarding any discription fixed in any position with nails or hinges, complete all as specified & directed.
250
-
-
Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified & directed.
150
-
-
Taking down shutters of any description exc. 1 sqm and not exc. 2 Sqm each, complete all as specified & directed.
184
-
-
Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified & directed.
1645
-
-
Demolition of stone sett paving of any description or thickness, laid, bedded and pointed in any mortar, complete all as specified & directed.
160
-
-
Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (Reinforcement cut as required to facilitate demolition), complete all as specified & directed.
160
-
-
Taking up or down steel tubing and connections 15mm bore, complete all as specifed & directed.
800
-
-
Taking up or down steel tubing and connections 20mm bore, complete all as specifed & directed.
1000
-
-
Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish, vegitation outside complex (MOD land), complete all as specified & directed.
6238
-
-
M&L for Rendering 15 mm thick in ready mix plaster on fair faces of brick work or concrete surfaces, finished even and fair without using extra cement, height of building upto 4th story, complete all as specified and directed.
5543
-
-
M&L for Rendering 5 mm thick in ready mix plaster on ceiling concrete surfaces finished even and fair without using extra cement, complete all as specified and directed.
695
-
-
Supply only integral water proofing compound (ISI marked), complete all as specified and directed.
20
-
-
M&L for chipping out spilled and loose concrete cover and derusting steel reinforement of concrete column, beam, slab, chajjas, parapets and the like as directed upto 25 to 35mm thick roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry including derusting steel wire reinforecement, providing fabric MS wire mesh 75 x 75 x 2mm as reinforcement to concrete surface applying adhesive/admixture over steel mesh and providing 25mm average thickness guniting mix using one part of OPC 53 grade and two part of gaggar sand mixed with adhesive/admixture @ pressure of 2.5 to 3.00kg/Sqcm by guiniting machine and surface finished even and fair including necessary padding, shuttering/scaffolding, formwork (guniting work to be carried out upto 15 metre height), complete all as specified and directed at site. Notes :- (a) After placing the additional reinforecement all concrete surfaces shall be throughly scrubbed with wire brushes, washed with water and allow to dry, apply chemistic polycretes admixture @ 2.25 kg by weight of cement all as per manufacturers instructions. (b) When polymix concreting in taking condition, guiniting is done with polycrete admixture @ 2% by weight of cement all as per manufacturers instructions (polycrete admixture shall be procured from chemical adhesive Pvt Ltd Co or their authorised dealer). (c) Cost of the above aspect shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account.
150
-
-
M&L for two coats of oil bound distemper including preparation of new plastered surfaces over one coat of alkali resistant primer & including 1mm thick wall care putty complete all as specified and directed.
3795
-
-
M&L for preparation of newly plastered surfaces of ceiling and applying two coats of white wash, complete all as specified & directed.
695
-
-
M&L for preparation of newly plastered surfaces of walls and providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with acrylic smooth exterior paint of required shade with two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm, complete all as specified and directed.
1748
-
-
M&L for preparation of old decorated plastered surfaces of walls, complete removal of existing treatment by rubbing, brooming down, washing with water etc and providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with acrylic smooth exterior paint of required shade with two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm, complete all as specified and directed.
1800
-
-
M&L for complete removal of existing treatment from old decorated plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer over 1mm thick wall care putty, complete all as specified & directed.
3565
-
-
M&L for preparation of old painted surface of ceiling and applying two coats of oil bound distemper on ceiling, complete all as specified and directed.
3000
-
-
M&L for 18mm thick WPC Prelam board solid flush type selected colour fixed with necessary screws solvent cement adhesive to make timber frame work as in kitchen cabinet as per sample, complete all as specified and directed.
350
-
-
M&L for teak wood lipping, 6mm thick fixed with nails to 18mm thick veneered particle borad including polishing, complete all as specified and directed.
900
-
-
S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30mm, complete all as specified & directed.
105
-
-
S&F 40mm dia, copboard knobs fixed with nut, screw and washer of mild steel, brass polished, complete all as specified & directed.
300
-
-
S&F ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed, complete all as specified & directed.
300
-
-
S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with meter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.
475
-
-
S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charg, omplete all as specified and directed.
Note : Stainless steel butt hinges and necessary S.S screws shall be paid for separately.
131
-
-
S&F of Stainless steel auto closing hinges openable at 0 degree for kitchen cabinet shutters and bed room cub boards, complete all as specified and directed. Make: Hettich, Ebco, Prime
900
-
-
S&F of stainless steel handles 100 mm size for kitchen cabinet shutters and bed room cub boards, complete all as per specified and directed. Make: Hettich, Ebco, Prime, Inox
800
-
-
S&F brass chromium plated tubular hanger rod 20 mm dia with suitable brackets complete all as specified and directed.
400
-
-
S&F PVC magnetic door catches of kitchen cabinet and similar work fixed with MS screws, complete all as specified and directed.
150
-
-
S&F mild steel framed work as in door or gates of angle or other sections, cooler stands, with gusset plates rails, braces etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and purpose made hinges or steel sheeting or other covering, running rails and guides) and hanging, fastening and fixing complete conforiming to Fe 290 Gde E-165, complete all as specified and directed.
2000
-
-
S&F Factory made double rebated extruded WPC (Wood Polymer Composite) Soild door/window/Ceosetory windows & other frames/chowkat of size 50 x 60 (Suspension Grade), Calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and nontoxic additives (Max toxicity index of 12 of 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58 N/mm and resistance to flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardent and fixed with MS Holdfast /lugs/SS dash fasteners of required dia and length complete as per direction of Eng-in charge. Note : For WPC soild door/winodow frames, minus 5mm tolerance in diamension i.e depth and width of profile diamension i.e on plus side shall be accepatable but no extra payment on this account shall be paid.
727.5
-
-
S&F 30mm thick factory made wire mesh solid WPC door shutter consisting of Density 650 kg /cbm manufactured by an ISO-9001-2015 certified company, Door to be panneled with SS mosquito mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as oer IS:4020). The door should be water proof, termite proof, fire retardent and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm x 25mm x 2mm and 32 mm long steel screw drilled suitable to pass through other hardware shouldbe fixed with 19 x 6 mm size steel screw etc, complete as as specified and as per direction of Engineer-in-charge, manufacture's specification and drawings Note : Fixture/fitting shall be measured & paid for separately.
255
-
-
S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn-charge ,complete all as specified and directed.
Note: Stainless steel butt hinges and necessary S.S screws shall be paid for separately
200
-
-
S&F stainless steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized iron staples including wooden beadings, complete all as specified and directed.
350
-
-
S&F aluminium anodised barrel tower bolt extruded section 200mm long and fixed with MS screws, complete all as specified & directed.
800
-
-
S&F 150 mm extruded aluminium alloy handle anodised fabricated type and fixed with MS screws, complete all as specified & directed.
800
-
-
S&F 200 mm extruded aluminium alloy handle anodised fabricated type and fixed with MS screws, complete all as specified & directed.
200
-
-
S&F 300 mm extruded section aluminium alloy anodised, sliding door bolt with hasp and staple and fixing clip of sheet and fixing bolt and nut, complete all as specified & directed.
150
-
-
S&F 300 mm MS ordinary rat tail rod pattern spring including roller and roller plate complete fixed on wooden frame or on wall with wooden plugs and set in cement mortar, complete all as specified & directed.
100
-
-
S&F SS butt hinges medium weight 100 mm size fixed with SS screws, complete all as specified & directed.
900
-
-
S&F brass chromium plated magic eye, complete all as specified and directed.
50
-
-
S&F in repairs floor door stopper 140mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and as directed.
250
-
-
Taking down wooden door shutter exc 1.00 Sqm and n. exc 2.00 Sqm each and refixing in same opening, complete all as specified & directed.
200
-
-
S&F in repairs looking mirror of size 600mm x450mm x5.5mm thick with aluminium frame selected quality mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified & directed.
50
-
-
S&F in repairs Stainless steel sink with drainage board made of stainless steel 1mm thick for kitchen or laboratory with stainless steel grating, plugs, washers and wastes, connecting union, stainless steel waste coupling, PVC waste pipe of 40mm size etc including bedding in cement mortar to dwarf wall or including fixing cantilever cast iron bracket, overall size 915x460mm with bowl size 410x330x160mm, complete all as specified & directed.
50
-
-
M&L for welding in repairs not exc 2.5 cm in length and not exc 6mm thick matel complete all as specified and directed
50
-
-
M&L 20mm CPVC pipes SDR 11 with all plain CPVC SDR 11 and brass threaded fittings like elbow, Tee, MTA/ BTA Adoptor, tank adeptor etc. and fixed complete to walls, ceiling or laid in floor, complete all as spd and directed.
1040
-
-
All as per item No 51 above but 25mm dia.
1000
-
-
M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc,; and cutting chases for concealed water tubing or concealed conduit wiring etc., and making good, cutting exc. 10cm but n exc 20cm girth in brick/stone walls, complete all as specified & directed.
639
-
-
S&F vitreous China, wash hand basin (pedestal), flat back white of size 550mmx400mm including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, PVC 32mm dia waste pipe, chain and plug including cutting for and pinning in ends of brackets or erecting stand, complete all as specified.
50
-
-
S&F in repair vitreous China wash down water closet pan (pedestal pattern) wall mounted white including 'P' or 'S' 100 mm trap and making good the disturbed surface to match with the existing, complete all as specified and directed.
50
-
-
Supply only plastic water closet seat cover white closed pattern with flat bottom end cover and mild steel chromium plated hanging device, complete all as specified and directed.
50
-
-
S&F in repairs PVC low level white flushing cistern valveless syphonic action type 10 lts capacity with inlet, ball valve, float and handle including PVC flush pipe 32 mm dia with bend and a pair of mild steel angle iron brackets of suitable size including making necessary connections to water supply pipe line and WC, complete all as specified and directed.
50
-
-
S&F in repairs bib taps 15 mm bore chromium plated brass, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed.
150
-
-
S&F in repairs Stop Valve /gate valve 20 mm dia cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or unions, complete all as specified and directed.
50
-
-
S&F in repairs angle valve/concealed Stop cock fancy type, chromium plated brass, 15mm, complete all as specified and directed.
200
-
-
S&F in repairs PVC connection 15mm dia and 60 cms long with two nos of brass nuts and washers, complete all as specified & directed.
150
-
-
S&F in repairs shower rose, chromium plated brass, fancy type, 125x125 mm, with or without swivel , any size, including fixing to steel pipe or union, complete all as spepcfied and directed.
50
-
-
S&F Stop valves, cast copper alloy, 15mm bore, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., fixed in repairs, complete all as specifed & directed.
50
-
-
S&F in repairs Glass Corner Shelf of 8mm thick including CP railing radius 250mm complete all as specified and directed.
50
-
-
S&F in repairs kitchen plate rack with four shelves made out of stainless steel sheet of 1mm thickness over all size 90x80x25cm, complete all as specified and directed.
50
-
-
S&F in repairs stainless steel of AE-SI-316 grade towel rack of size 600mmx300mm including a pair of brass bracket, complete all as specified and directed.
50
-
-
S&F in repairs brass chromium plated tubuler towel rail 20mm dia D type ISI marked 60cm long between flanges including a pair of CP brass brackets, complete all as specified)
50
-
-
S&F in repairs brass chromium plated soap dish, complete all as specified and directed.
50
-
-
S&F in repairs 25mm outer dia stainless steel decorative drapery rod (including necessary fittings) of thickness 20 gauge, for every 1 RM length provide 10 numbers stainless steel wings of 50mm dia and proportionate for part off with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod ar both ends, complete all as specified & directed.
Note: The drapery rod shall be projected 150mm outer side from the closer opening of doors/windows.
460
-
-
S&F in repairs stainless steel peg set of 6 peg, 45 centimeter long, complete all as specified and directed.
50
-
-
M&L for glazed ceramic coloured tiles of size 450mmx300mm, thickness 7 to 8mm as in vertical surfaces such as wall, pillar, skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed.
1270
-
-
M&L for non skid ceramic rectified coloured tiles, 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but nexc 0.11 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:6, complete all as specified and directed .
375
-
-
M&L for non skid ceramic coloured tiles, 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but nexc 0.38 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:6, complete all as specified and directed .
2600
-
-
All as per Srl Item No.73 above but on vertical surfaces such as skirting/dado etc. set & jointed in neat cement slury & pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4.
200
-
-
M&L for machine cut kota stone slab flooring, 20-25 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, grinding and polishing laid over and including 20mm screed layer in cement mortar 1:4, complete all as specified & directed.
140
-
-
M&L for machine cut kota stone slab, 20-25 mm thick as in vertical surfaces such as skirting/dado etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, grinding and polishing, laid over and including 10mm thick screed bed in cement mortar 1:4, complete all as specified & directed.
15
-
-
M&l for 18-20mm thick granite stone work (table rubbed and polished) machine cut in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, cutting polishing, half rounding of exposed edges of stone slabs, hole for gas pipe line over & including 15mm thick screed bed in cement mortar 1:4, complete all as specified & directed.
200
-
-
M&L for 75 mm thick cement concrete 1:3:6 type C1 using 20mm graded crushed stone aggregate as in plinth protection, laid to slope of 1 in 24 in alternate basis system, surfaces even and smooth without using extra cement, each bay shall not exceed 3m in length, 0.75m wide & 75mm deep joint shall be formed between the bays which shall be filled with Mastic filling to full depth comprising a mixture of 1 part of heator hot blow bitumen 85/25 portion and two parts of heated badrapur sand (by volume), complete all as specified and directed.
225
-
-
M&L for forming construction joint 75mm deep x 10mm wide filled with sealing compound Grade A, complete all as specified and directed.
6
-
-
S&F glass dividing strips, 38mm wide and 3mm thick and inserted in position to conform to design, complete all as specified and directed.
60
-
-
M&L for providing cement concrete 1:2:4 type B-I using 20mm graded aggregate in roof kerb or mud slops, rounded or chamfered on edges, plinth courses, coping, kneelers, apex stone, kerb water tough and the like including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work, complete all as specified and directed.
15
-
-
M&L for use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified & directed.
150
-
-
M&L for RCC M-25 design mix cement concrete (20mm graded aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies deck slabs and in shelves and the like, complete all as specified and directed.
4.5
-
-
S&F TMT bars 10mm dia & over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified & directed.
2100
-
-
Dismantling water tanks of capacity exc 250 litres but n exc 500 litres, complete all as specified & directed.
50
-
-
S&F rotationally moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted & fixed in position of capacity 500 ltrs including making necessary arrangements for fixing of inlet, outlet, over flow pipe, wash out pipe, complete all as specified & directed.
34
-
-
S&F in repairs PVC (SWR) pipes, double socketed in any length with rubber ring joints, fixed to walls 110mm mm dia, in four storey building, complete all as specified and directed.
270
-
-
S&F in repairs PVC (SWR) bends of any radius of 110mm bore including jointing with solvent cement, complete all as specified and directed.
84
-
-
S&F in repairs Grating doom 125 mm dia with waste hole of PTMT (minimum weight - 40 gms, complete all as specified and directed.
50
-
-
M&L for Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:6, complete all as specified & directed.
165
-
-
M&L for brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan to any radius, half brick thick walls built in cement mortar 1:4, complete all as specified & directed.
150
-
-
S&F in repairs stainless steel grating of 100mm size (square/round), male/female pattern with or without hole, fixed in nahani/floor traps with white/coloured cement, complete all as specified & directed.
100
-
-
S&F Mild steel framed work as in grills, gratings, etc. with ends of bars shouldered and or reveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 grade-E-165, complete all as specified & directed.
7000
-
-
S&F powder coated (minimum thickness of powder coating 50 micron) aluminium section for shutters suitable for three/four track window and aluminium section weighting more than 0.5 kg/m of sliding members including all necessary fittings and fixtures, jointing cleats, rubber packing etc, complete all as specified and directed.
300
-
-
S&F powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, side hung type with/ without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21, 100mm long (2 Nos) suitable handle (1 No) complete all as specified and directed.
125
-
-
S&F 4mm thick pin headed glass (figured) panes used in anodised aluminium glazed/gauzed windows and ventilators shutters, complete all as specified and directed.
40
-
-
S&F 5.5mm thick sheet glass selected qualities for aluminium windows in sqm n exc 0.5 sqm each pane, complete all as specified and directed.
130
-
-
S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple, complete all as specified and directed.
200
-
-
Demolition of Bricks (laid flat or on edge) or brick tiles in roof/floors, channels, kerbs, aprons, etc. (each layer), removing out from defence land, complete all as specified and directed.
1350
-
-
S&F Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) 78, solar reflection 0.70 and initial emittance 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner, complete all as specified and directed.
1350
-
-
Demolition of mud phuska on roof slabs, any thickness including cleaning of roof surfaces and removing the debris upto the distance exc 1.00 Km but not n.exc 1.5 Km, complete all as specified and directed.
250
-
-
Scraping old tar felt roof treatment over concrete padding of any thickness etc from roof including finishes or junction or parapet and cleaning the surface, complete all as specified and directed.
1350
-
-
M&L for RCC M-25 design mix grade cement concrete for reinforced cement concrete work using 20mm graded crushed stone aggregate as in slabs, beams, parapet wall, RCC wall, RCC column etc position of using cement content as per approved design mix, including pumping of concrete to site of laying and the cost of centering, shuttering, form work, finishing and excluding reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.The Mix design as per particular specifications shall be got approved by Engineer-in-Charge before execution of the item.The rate shall include cost of all specified materials and operations at all levels and heights, including the cost of centering, shuttering and form work excluding reinforcement which shall be paid under relevant item, complete all as specified and directed.
Note :- Cement content considered in this item is @ 300 kg/cum as per IS 456 table showing minimum cement content. No extra will be paid nor any amount will recovered on account of variation of cement in mix design as per specifications for controlled concrete.
160
-
-
M&L for water proofing treatment to roof surface with APP polymeric based water proofing membrane 3mm thick & weighing not less than 3.5 Kg / Sqm of approved make black finish consisting of a central core of high molecular high density polyethylene film (HMHDPF) & reinforced with non woven polyester matt of min 160 gm/sqm with a thermo fusible finish laid over a coat of hot blown bitumen of 85/25 grade conforming to IS 702 @ 1.2 kg/sqm over a coat of an bitumen primer conforming to IS-3384 @0.4 Ltr/Sqm over prepared roof surfaces, forcing overlap with a propane or a butane gas torch with a overlap of 75mm at sides & 100mm at ends & sealing including applying a coat of cold emulsion bituminous primer complete as per manufacturer's instructions complete all as specified and directed. (Make Super thermolay manufactured by STP Ltd or 'Hyper Plas' (Polyster) manufactured by M/S IWL Ltd or 'Shalipals' (polyster) manufactured by M/S Capital Steels and chemicals Pvt Ltd)
Notes :- 1. Water proofing treatment shall be got carried out by the manufacturer or their authorised applicator only.
2. Bitumen primer, bitumen and membrane shall be of same make / manufacturer. 3. The APP Membrane to be inserted in the parapet wall/wall by cutting chases of at least 65mm X 50mm size & making good in cement mortar 1:3.
1350
-
-
M&L for cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate on roof padding with using water proofing compound as per manufacturers instructions, surface finished even and smooth without using extra cement ,complete all as specified and directed. Note : Rate of WPC shall be deemed included in unit rate of this item.
75
-
-
M&L for cement concrete 1:5:10 type E2 using 40mm graded crushed stone aggregate as in filling of sunken portion and similar items, complete all as specified and directed..
14.5
-
-
Dismantling of cast iron drain pipes, jointed in cement mortar and taking out of trenches, if required, Internal dia of pipe 100mm, complete all as specified & directed.
180
-
-
Dismantling of cast iron drain pipes, jointed in cement mortar and taking out of trenches, if required, Internal dia of pipe 75mm, complete all as specified & directed.
360
-
-
S&F cast iron soil, waste and vent pipe, sand cast, 100mm bore in any length with or without ears with cement joints, laid in trenches or in floors/walls, complete all as specified & directed.
165
-
-
S&F cast iron soil, waste and vent pipe, sand cast, 75mm bore in any length with or without ears with cement joints, laid in trenches or in floors/walls, complete all as specified & directed.
331.2
-
-
S&F 100 mm bore cost iron 'P' or 'S' traps fixed with lead joints, complete all as specified and direced.
50
-
-
S&F 100mm bore cast iron bends/T (any radius) diminishing pieces or tapers (larger bore to be measured) with oval access doors, complete all as specified and directed.
50
-
-
S&F 75mm bore cast iron bends/T (any radius) diminishing pieces or tapers (larger bore to be measured) with oval access doors, complete all as specified and directed.
100
-
-
S&F 100mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches including oval access door, complete all as specified & directed.
50
-
-
S&F 75mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches including oval access door, complete all as specified & directed.
100
-
-
S&F CI Cowl for 100mm bore for CI pipe, complete all as specified and directed.
15
-
-
M&L for preparation of old wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.
900
-
-
M&L for preparation of old steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.
250
-
-
S&F brass CP vertical mixer for mixing hot & cold water for wash hand basin screwed down for 15 mm bore iron pipe or ferrule, complete all as specified and directed.
50
-
-
S&F CP wall mixer non telephonic type for mixing hot and cold water for shower screwed down for 15 mm brass iron pipe or ferrule, complete all as specified and directed.
50
-
-
S&F in repairs ball valve high pressure of PTMT with epoxy coated aluminum rod and high density polythene float and flynut complete, screwed for iron pipe or brass furrule size 25mm bore (Min weight 210gms), complete all as specified and directed.
50
-
-
S&F 25mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides as shutter of cupboard, complete all as specified and directed.
85
-
-
M&L for providing 40mm thick PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate using integral WPC, surface finished even and smooth with using extra cement, complete all as specified and directed. Note: Integral water proofing compound shall be measured & paid for seperately under respective item.
55
-
-
M&L for 10mm thick rendering in cement mortar 1:3 on brick/concrete surfaces using integral water proofing compound, surface finished even and smooth without using extra cement, complete all as specified & directed.
Note : Integral water proofing compound shall be measured & paid for seperately under respective item.
150
-
-
M&L for 15mm thick protection plaster in cement mortar 1:3 using integral water proofing compound, surface finished even and smooth without using extra cement, complete all as specified & directed.
Note : Integral water proofing compound shall be measured & paid for seperately under respective item.
138
-
-
M&L for providing 40mm dia GI pipe spout projecting at least 150mm beyond outer face of wall, complete all as specified and directed.
45
-
-
M&L for glass fibre reinforced acrylic modified cementious coating system with base coat of Sika Top @ Seal 107 or equivalent @ 1.50 Kg/Sqm fibre reinforcement Sika ® Fab-1 and top coat with Sika Top® Seal-107@ 1.50 Kg/Sqm or equivalent of FOSROC or PIDILITE, complete all as specified and directed
138
-
-
S&F powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, beading for grill with one or more rebates including joining cleat for fixing etc., complete all as specified and directed .
2152.5
-
-
Supply only CP waste coupling 32mm size with PVC waste pipe, plugs and washers for kitchen sink ,complete all as specified & directed.
50
-
-
M&L for followings :-i) Removing plaster & finishes from all exposed / damaged portion of columns, slabs & beams (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible)(iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed)(iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. (The Engr-in-charge may order sand blasting if rust is approved)(vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out, complete all as specified and directed
210
-
-
M&L for providing rust proof /anti corrosive treatment to bars -i) cleaning of all exposed bars (new & old) alround(ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer(ili) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note: Anti corrosive treatment shall be continuous specially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating, complete all as specified and directed.
150
-
-
M&L for providing PMM (Polymer modified cementitious mortar ) :-(i) Dry sub strate
surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes) (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note: Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use.(iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.
200
-
-
S&F 12mm dia steel sheer connector in grid pattern in between old core and Eac new concrete as wherever directed by Engr-in-charge and as specifed by manufactuer Including drilling hole of depth of 100 mm and chemical anchoring with pure epoxy resin anchoring mortar (Master flow 935 of BASF or equivalent FOSROC/SIKA). (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item), complete all as specified and directed.
1500
-
-
M&L for Providing & Pouring Micro concreting M-40 grade -(i) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes) (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade, Make: Master Emaco S46T of BASF or equivalent FOSROC/SIKA using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc, Adding of aggregates will be permitted only as per manufacturer's recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed. Note: The cost of micro concrete M-40 grade & Epoxy bond coat is deemed included in this item.
30
-
-
M&L for Drilling & chemical anchoring of new rebars/stirrups -i) Drilling in to the sound
RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under -8 mm dia bar - drilling length 80 to 100 mm, complete all as specified and directed. Note: Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar (Master flow 935 of BASF or equivalent FOSROC/SIKA) with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is deemed included in this item
600
-
-
M&L for Drilling & chemical anchoring of new rebars/stirrups :-(i) Drilling in to the sound
RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under -16 & 20 mm dia bar - drilling length 160 to 180 mm, complete all as specified and directed.
Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar (Master flow 935 of BASE or equivalent FOSROC/SIKÀ) with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is deemed included in this item)
220
-
-
M&L for impregnating cream for injection into masonry or concrete wall 230mm thick against capilary rising humidity. Rising bar super strong (Product no. 201) of chowgale building chemicals or equivalent pidlite/Drfixit/sika/phosrock, complete all as specified and directed
Method of Application
Methodology
(a) The surface must be sound , absorbent, clean, free of dust, oil, paint, curing agents , loose cement or lime plaster & concrete, debris, or any separation layers.
(b) The plaster must be knocked off at least 50cm beyond the visibly penetrated area.
(c) Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. All sharp edges/joints need to be levelled ; loose concrete to be removed.
(d) Drill boreholes at ground level horizntally. The boreholes are drilled horizontal into the masonry. (e) The holes should be drilled until a depth of approx 5cm (for a 6cm thick wall) before the end of the wall is reached. The boreholes should have a diameter of 12mm upto a maximum of 15mm and should be spaced approx 100-120mm apart and the vertical offset is 6cm maximum.
(f) Before inserting rising bar super strong or equivalent the boreholes must be clean from boring dust by using air pressure. It is not necessary to pre-wet the boreholes. (g) For applying of rising bar of super strong or equivalent the dosing system inserted as far as possible into the bore holes. While dosing the product uniformly, the injection nozzle is pulled out leading to a completely filled boreholes
(h) Treatment of highly absorbent masonary mught required repeated filling of the boreholes. depending upon extent of damage, rising bar superstrong or equivalent can be re-injected into the same hole after 24 hrs. depending on observency, application or masonry thickness 0.1 to 0.15 ltr/m with 10cm wall thickness.
300
-
-
M&L for Preventive treatment against the danger of carbonation in exposed faces of RCC members :-
(i) Cleaning existing surfaces of RCC members and making surface free of loose material, oil, grease etc. by vigorous wire brushing including light grit blasting where necessary as recommended by Engr-in-charge.
(ii) Further, cleaning using biocide (as recommended by manufacturer) to ensure that surface is free of algae and fungus and no trace of paint (any type) left out. Sand blasting to be done to remove trace of paint.
(iii) Cleaned surface to be allowed to dry.
(iv) Spray a coat of primer (as recommended by manufacturer) over dry cleaned surface as required prior to final finish. Primer shall be diluted in proposition 2:1 with mineral turpentine. After application, primer shall be allowed to dry for 03 hours or as directed.
(v) Apply a coat of neat Aliphatic Acrylic anti-carbonation (ACC) over the primed surface with air / spray gun at nominal rate of 3.5 ltrs per sqm as recommended by manufacturer.
(vi) Apply a more coat of Aliphatic Acrylic anti-carbonation (ACC) after 5-6 hours as recommended by manufacturer complete all as specified and directed.
850
-
-
M&L for use & waste of form work using steel sheet, steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period, complete all as specified and directed.
Note : Form work shall be 100% leak proof. For purpose of payment area in touch with concrete shall be measured.
200
-
-
S&F for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
18500
-
-
All as per item No.140 above but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders.
450
-
-
S&F FRP chajjas of 450mm wide suitable for various openings including fittings and fixtures upto 4 storey bldg complete all as specified and directed.
250
-
-
Refixing of balcony grill without damage including welding, cleaning rust and apply zink primer and fixing at same place without any damage to existing structure etc complete all as specified and directed. Note : The cost of dismantling of all balcany grill up to 4 storey building without any damage and refixing at same place is deemed included in this item.
35
-
-
M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. including brushing neat cement slurry with 3.0kg of cement per sq. Metre, complete all as specified & directed.
2600
-
-
M&L providing pre cast cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in kitchen slab, passage roof etc and set in cement mortar 1:4, complete all as specified & directed.
10
-
-
M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of syntethic enamel paint over one coat of red oxide zinc chrome primer, complete all as specified & directed.
250
-
-
S&F brass CP mixer swivel spout for mixing hot & cold water for sink, screwed down for 15mm bore pipe or ferrul, complete all as spd & directed.
50
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%