Military Engineer Services Tender
If you're typing tender ID over and again or finding it difficult to go through the cumbersome government websites for looking at Delhi tenders online. We have come up with a solution i.e. we have collated every eprocurement Delhi tender on BidAssist. Also, for any queries related to an e-tender Delhi, like the bidding process, registration process, etc., the same are explained below.
Costs
EMD
₹ 96,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_684419_1Tender No
NIT No GE/ND-95/2024-25Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
M&L for complete removal of existing treatment and applying 1mm thick wall care putty to achived smooth surface and then applying two coats of oil bound distemper over a coat of chalk whitening as priming coat after preparation of ceiling surfaces complete all as specified and directed. Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimun regional HQs) issued not earlier than 30 days days from bid start date of the said work.
(c) The contractor shall provide application,testing and certification of finishes by paint manufacturing firms/their authorised applicators.
(d) Cost of above mentioned shall also included in quoted rates.
1500
-
-
M&L for preparation of old surface and apply one coat Plastic emulsion paint (ready mix 1st quality) having of approved manufacturer complete all as specified and directed.
Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimun regional HQs) issued not earlier than 30 days days from bid start date of the said work.
(c) The contractor shall provide application,testing and certification of finishes by paint manufacturing firms/their authorised applicators.
(d) Cost of above mentioned shall also included in quoted rates.
150
-
-
M&L for complete removal of existing treatment and applying texture paint as per design and shape and size shall be as directed by engr-in charge with 1st quality of glossy or matte plastic emulsion paint over a coat of base paint over 2 mm thickness cement base putty over plastered surface to prepare the surface even and smooth complete all as specified and directed.
Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimun regional HQs) issued not earlier than 30 days days from bid start date of the said work.
(c) The contractor shall provide application,testing and certification of finishes by paint manufacturing firms/their authorised applicators.
(d) Cost of above mentioned shall also included in quoted rates.
50
-
-
M&L for applying one coat of white wash on old decorated ceiling surfaces including preparation of surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salt and greesy spots complete all as specified and directed.
3500
-
-
M&L for applying one coat of cement base paint on old painted wall surface including preparation of surfaces complete all as specified and directed.
Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimun regional HQs) issued not earlier than 30 days days from bid start date of the said work.
(c) The contractor shall provide application,testing and certification of finishes by paint manufacturing firms/their authorised applicators.
(d) Cost of above mentioned shall also included in quoted rates. (e) work shall be execuated up to six story bldgs
8000
-
-
M&L for preparation of old surfaces of walls by completet removal of existing and after preparation of surfaces applying primer and further applying two coat of cement base paint complete all as specified and directed.
Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimun regional HQs) issued not earlier than 30 days days from bid start date of the said work.
(c) The contractor shall provide application,testing and certification of finishes by paint manufacturing firms/their authorised applicators.
(d) Cost of above mentioned shall also included in quoted rates. (e) work shall be execuated up to six story bldgs
3000
-
-
M&L complete removal of existing treatment and applying finishing walls with Acrylic Smooth exterior paint of required shade more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.
Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimun regional HQs) issued not earlier than 30 days days from bid start date of the said work.
(c) The contractor shall provide application,testing and certification of finishes by paint manufacturing firms/their authorised applicators.
(d) Cost of above mentioned shall also included in quoted rates. (e) work shall be execuated up to six story bldgs
2100
-
-
M&L for Washing, rubbing down and stopping of old surface and applying one coat of acrylic Smooth exterior paint of required shade complete all as specified and directed. Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimun regional HQs) issued not earlier than 30 days days from bid start date of the said work.
(c) The contractor shall provide application,testing and certification of finishes by paint manufacturing firms/their authorised applicators.
(d) Cost of above mentioned shall also included in quoted rates. (e) work shall be execuated up to six story bldgs
7575
-
-
M&L for applying one coat of synthetic enamel paint on old painted wooden surfaces of any description not otherwise described over 10 cm width or girth including preparation of surfaces complete all as specified and directed.
Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimun regional HQs) issued not earlier than 30 days from bid start date of the said work.
(c) The contractor shall provide application,testing and certification of finishes by paint manufacturing firms/their authorised applicators.
(d) Cost of above mentioned shall also included in quoted rates.
400
-
-
M&L for complete removal of existing treatment and applying two coat of synthetic enamel paint over one coat of primer of wooden surfaces of any description not otherwise described over 10 cm width or girth including preparation of surfaces complete all as specified and directed.
Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimun regional HQs) issued not earlier than 30 days from bid start date of the said work.
(c) The contractor shall provide application,testing and certification of finishes by paint manufacturing firms/their authorised applicators.
(d) Cost of above mentioned shall also included in quoted rates.
300
-
-
M&L for applying one coat of synthetic enamel paint on old painted steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surfaces complete all as specified and directed.
Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimun regional HQs) issued not earlier than 30 days from bid start date of the said work.
(c) The contractor shall provide application,testing and certification of finishes by paint manufacturing firms/their authorised applicators.
(d) Cost of above mentioned shall also included in quoted rates.
500
-
-
M&L for complete removal of existing treatment and applying two coat of synthetic enamel paint over one coat of primer of steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surfaces complete all as specified and directed.
Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimun regional HQs) issued not earlier than 30 days from bid start date of the said work.
(c) The contractor shall provide application,testing and certification of finishes by paint manufacturing firms/their authorised applicators.
(d) Cost of above mentioned shall also included in quoted rates.
500
-
-
Taking down cement plaster on brick Walls built in cement mortar including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.
675
-
-
M&L for rendering 15 mm thick in cement mortar 1:6 on conc/ brick surfaces, finished even and smooth without using extra cement complete all as specified and directed.
100
-
-
M&L for 15mm thick cement plastering in cement mortar 1:4 with Water Proofing Compound @200 ml/per bag of cement on fair faces of brick work or concrete surfaces finished even & fair without using extra cement complete all as specified and directed. Note: WPC will be measured and paid saparately
100
-
-
M&L for 5mm thick cement plastering in cement mortar 1:3 as on ceiling surfaces finished even and smooth without using extra complete all as specified and directed.
100
-
-
Supply only liquid water proofing compound as per manufacture instruction complete all as specified and directed.
5
-
-
M&L for Preparation of new plastered surface and applying one & more coat of white putty min 1 mm thick on wall surfaces over a coat of chalk whiting priming over two coat of disteemper oil emulsion complete all as specified and directed.
125
-
-
M&L for Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and directed.
175
-
-
M & L for prepapation of new plaster serface of walls and applying two coats of acrylic emultion weather coat paint over a coat of primer over 1mm thick cement base wall care putty complete as specified and directed.
100
-
-
M&L for uprooting plants (girth n.exc 15 cm of trunk to any of plants grown along the pipes or walls chajjas, parapets and roof of building and making good the surface as per existing surface and pouring acid not less than 100ml for each plant in the roof to avoid further growth complete all as specified and directed.
Note:-Work has to be executed in multi storey bldgs upto 25 Meter height
1200
-
-
Cleaning of existing sewage lines of any dia and depth by roding manually or with MACHINICAL PROCESS as required at site from manhole to manhole, removing blockage of any type , flushing the line with pressure water jets and making the line fully functional including manhole cleaning complete all as specified and as directed by Engineer-in-charge
150
-
-
Excavation in trenches n exc 1.5 m wide and n exc 1.5 m deep for foundation and getting out in soft/loose soil complete all as specified and directed.
55
-
-
Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25 cm soft/ loose soil complete all as specified and directed.
10
-
-
Removing excavated materials n exc 50 m and depositing where directed at a level n exc 1.50 mtr above the starting point complete all as specified and directed.
45
-
-
Demolition and breaking up drain pipes salt glazed stone ware pipes 150 mm dia (internal) set in cement mortar complete all as specified and directed.
150
-
-
Material and labour for HDPE Black DWC Sewerage and Drainage Pipe 150 mm in trenches and jointed with using ruber gaskit and pipe joint lubricant for both end and 150 to 200 mmd wide color joint socket shll be provided to cover the joint all around as per specefication and manufacture insturction complete all as specified and directed.
150
-
-
M&L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm/160 mm bore pipes complete all as specified and directed.
140
-
-
Cleaning of MANHOLE of capacity upto 2.00 cum by using mobile high pressure super sucker macnine consisting of two tanks (a water tank and a sludge tank), or alternatively two vehicles (super sucker unit and dump tanks), a high pressure water jet pimp and a high flow jetting blower or vacuum pump for suction, pumping out sewae water accumulated night soil, sludge's (both soild and liquid) and other obstructive materials into dump tank and removing to outside of defence land immediately for disposal, re-fixing the cover after complete cleaning of septic tank, complete all as specified and as directed by Engr-in-Chagre.
Note :- 1. After removal of the sludges from the pits, the setic tank to be cleaned thoroughtly with wter.
2. Cleaning to be confirmed by the Engr-in-Charge of the work.
3. Care shall be given to maintain hygeinic condition while removing sludge/foul materials to pit etc. 3
4. Dates of measurment and location shall be recorded commensurate with users certificate of compliance in a register duly signed by the contractor & Engr-in-charge. 5. Cleaning of tanks once carried out shall not be repeated without written request of the user and approval of Engr-in-charge/GE. 6. Contractor should quote rate on whole job basis.
40
-
-
All as per Item No 32.00 above but of capacity 2.00 to 5.00 cum complete all as specified and directed.
30
-
-
All as per Item No 32.00 above but of capacity beyond 5.00 cum complete all as specified and directed.
5
-
-
Dismantling of cast iron or reinforced concrete drain pipe 100 & 75mm bore, jointed in cement mottor and taking out of treanches if required complete all as specified and directed.
74
-
-
S&F Cast iron soil,waste and vent sand cast pipes pipes in any length with or without ears,with cement joints,laid in trenches or in floors of size 100 mm bore complete all as specified and directed.
30
-
-
S&F Cast iron soil,waste and vent sand cast pipes pipes in any length with or without ears,with cement joints,laid in trenches or in floors of size 75 mm bore complete all as specified and directed.
25
-
-
S&F Cast iron soil,waste and vent sand cast pipes pipes in any length with or without ears,with cement joints, fixed to wall, of size 100 mm bore incl take necessary safety precaution during execution of the work up to 6 story buildings complete all as specified and directed.
30
-
-
S&F Cast iron soil,waste and vent sand cast pipes pipes in any length with or without ears,with cement joints, fixed to wall, of size 100 mm bore incl take necessary safety precaution during execution of the work up to 6 story buildings complete all as specified and directed.
24
-
-
S&F in repair Cast iron bends,tee, Y, elbow, branch piece with ducks foot or heel rest.of size 100mm bore of pipe complete all as specified and directed.
30
-
-
S&F in repair Cast iron bends,tee, Y, elbow, branch piece with ducks foot or heel rest.of size 75mm bore of pipe complete all as specified and directed.
22
-
-
Demolition of reinforced cement concrete of any description and any position no otherwise specifically ( below or above ground level) including cutting of reinforcement as required to facilitate demoilition incl removing the unserviceable material out side the MOD land complete all as specified and directed.
5
-
-
M&L for precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in landing, cover slab, manhole cover etc including necessary form work, set in cement mortar 1:4 complete all as specified and directed.
10
-
-
M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
225
-
-
M&L for cement concrete type C-2, 1:3:6 ( 20mm graded stone aggregate ) , 75 mm thick as in plinth protection , finished cement concrete surface even & smooth without using extra cement complete all as specified and directed.
100
-
-
M&L for cutting into existing manholes for connecting new drains, making good to pipes and renderning, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1, smooth finished and reforming benching as required for 150 mm internal dia of pipes complete all as specified and directed.
2
-
-
Dismantling of floor of size not exceeding 1.50 Sqm mtr for EWC/ IWC water closet and removing out the cinder/concrete from sunken portion, grinding any sharp edges etc all as specified and directed with following: (a) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc.
(b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite.
(c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified.
(d) M&L for providing 40 mm dia GI pipe spout projecting at least 150 mm beyond outer face of wall.
(e) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed.
(f) The area of Each WC portion is n.exc 1.50 Sqm each.
(g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account.
(h) 72 hrs Ponding test shall be carried out for sunken treatment before payment.
10
-
-
S&F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints using solvent adhesives fixed to walls with brackets etc of 110mm dia complete all as specified and directed.
70
-
-
S&F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints using solvent adhesives fixed to walls with brackets etc of 75 mm dia complete all as specified and directed.
50
-
-
S&F in repair PVC (SWR) bends, shoes, ' Y' and tee any radius of 110mm dia complete all as specified and directed.
20
-
-
S&F in repair PVC (SWR) bends,shoes, ' Y' and tee any radius of 75mm dia complete all as specified and directed.
20
-
-
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.
250
-
-
M&L for coloured non skid ceramic tiles 7 to8mm thick in floors, areaof each tile exc 0.11 sqm but not exc 0.18 sqm od 1st quality set & jointed in neat cement slurry and pointed in coloured cement to match over & including 20mm thick screed bed in CM 1:4 complete all as specified and directed.
60
-
-
M&L for 600mmX300mm and 7mm to 8mm thickness glazed ceramic tiles colored as in dado/skirting and vertical serfaces set & jointed in neat cement slurry and pointed in colored cement over and incl 10 mm thick cement mortar 1:4, Shade, pattern, laying etc of tiles complete all as specified and directed.
150
-
-
M&L for 10mm thick reeady mix plaster READIPLAST RP of (Make Ultra tech) on any surfaces of brick/concrete includidng aapplication of bonding coat as Ultratech seal and Dry 5 Plus as per manufacturers instruction including finished even and smooth includng taking down old plaster complete all as specified and directed.
Note: The work shall be carried out upto sixth storey height of buildings including all safety factor.
50
-
-
M&L for 5mm thick reeady mix plaster READIPLAST RP of (Make Ultra tech) on any surfaces of brick/concrete includidng aapplication of bonding coat as Ultratech seal and Dry 5 Plus as per manufacturers instruction including finished even and smooth on soffits/ceiling surfaces complete all as specified and directed. Note: The work shall be carried out upto sixth storey height of buildings including all safety factor.
75
-
-
M&L for finishing wall with Acrylic smooth exterior paint of required shade: New work ( two or more coats applied @ 1.67 Ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.20 Kg/10 Sqm) complete all as specified and directed.
112.5
-
-
Demolition of cement concrete unreinforced of any description and in any position not other wise specifically provided incling removing the unserviceable material out side the MOD land complete all as specified and directed.
35
-
-
M&L for lean concrete 1:4:8 type D2(using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.
2
-
-
M&L for PCC 1:3:6, type C-1 (using 20 mm graded Agg) as in drain finished even & smooth surface without using extra cement complete all as specified and directed.
4
-
-
M&L for 100 mm thick cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base or sub floors finishing the surfaces even and rough to receive the topping layer complete all as specified and directed.
250
-
-
M&L for cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in floor/path finished even and smooth surface without using extra cement complete all as specified and directed.
12
-
-
S&F in repair Vitreous China wash down water closet pan single piece syphonic action, white including soft close sheet cover of closed pattern with flat bottom complete all as specified and directed.
Make: Hindware Cat part No 20121, Cera Cat No. :S1013178VS, Jaguar Cat No SLS-WHT-6851S110PP
8
-
-
S&F in repair, brass chromium plated Health Faucet including flexible pipe of 15 mm bore and 1.20M long with and including 15 mm bore complete all as specified and directed.
Make: Jaguar of Cat No ALD-573, Hindware cat No SI-13081 SI-14001 and CERA Cat No. : F8030105AB
17
-
-
S&F in repair brass chromium plated toilet paper holder, complete all as specified and directed.
Make: Jaguar Cat No CAN-1151N, CERA Cat Part No F5007110, or Hindware cat No F880003CP
12
-
-
S&F in repairs Single Lever Basin Mixer Wall Mounted Consisting of Operating Lever, Cartridge Sleeve, Wall Flange, Nipple & Spout suitable for basin including all fittings complete all as specified and directed.
Make: Jaquar cat part no ALD-233N & ALD-235N, CERA Cat Part No G1017473, Hindware Cat Part No F570029CP
15
-
-
S&F in repair 3 in 1 conceled single lever shower mixter, Shower System, 300mm Shower with arm, hand shower 1m to 1.2m connection and one spout with 10 layer surface finished, Shower System owns a modern and stylish look . Excellent plating technology prevents the coating from falling off, after a long time use still keep the surface smooth and clean will all conneted items all as specefied by manufacture complete all as specified and directed.
Make Jaquar Cat No RP-CHR-10125PM , Hindware Cat No F570022CP & Cera Cat No. F1019403
20
-
-
S&F in repair Bib tab (spout) 15mm bore while with Wall Flange complete all as specified and directed.
Make Jagaur Model : code No OPP-15037PM, Hindware Cat Part No F340004C or Cera Cat No. : F1015151
45
-
-
S&F in repair Angular Stop Cock 15mm bore with Wall Flange while complete all as specified and directed.
Make : Jaguar model OPP-15053PM, Hindware Cat Part No F570043CP or Cera Cat Part No F8040204
45
-
-
S&F in repair vitreous china wash down water closet pedestal pattern white incl valveless syphonic action type PVC low level flushing cistern with inlet ball valve float & handle incl. brackets of 10 ltrs capacity with dual flush and saparate switch operated small flush: 2-3 ltr and Large flush: 8 to 10 ltrs complete with plastic water closet seat white closed pattern with flat bottom & cover & mild steel chromium plated or aluminium hinges device & flush pipe of polythene of low or high density of PVC 32mm dia for low level PVC cistern complete all as specified and directed.
12
-
-
S&F in repair water closet vitreous china squatting pan of ORISSA pattern size 580 mm X 440 mm white with integral foot rest incl setting the cast iron trap & pan into cement and sand mortar, provn of lime concrete bedding complete.incl valveless syphonic action type PVC low level flushing cistern with inlet ball valve float & handle incl. brackets of 10 ltrs with dual flush and saparate switch operated small flush: 2-3 ltr and Large flush: 8 to 10 ltrs capacity complete all as specified and directed.
20
-
-
M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6.00 m mean radius built in CM 1:6 including Demolition with removing the unserviceable material out side the MOD land complete all as specified and directed.
5
-
-
M&L for machine vibrated precast concrete interlocking paver/ tiles (glazed finish) with grey cement and pigment any shape, any size, confirming to IS 15658-2006 of 60 mm thick and M-35 grade over 50mm thick sand layer including taking down old existing flooring any type complete all as specified and directed.
150
-
-
M&L for cement concrete chequered tiles top PU quoted with size 300x300x22-25 mm thick with grey cement and no pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors over and including 15 mm thick screed bed in cement mortar 1:6 including taking down old existing flooring any type complete all as specified and directed.
250
-
-
Cleaning and removing all scales and dirt etc from existing tanks and from mouths of circulating pipes etc for exceeding or including 500 litres to 1000 Litres capacity of tanks complete all as specified and directed.
80
-
-
Cleaning and removing all scales and dirt etc from existing tanks and from mouths of circulating pipes etc for exceeding 1000 litres but n.exc 2000 Litres capacity of tanks complete all as specified and directed.
2
-
-
S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed.
20
-
-
S&F Pre- painted galvalume aluminum zinc coating GI based steel sheet with approved profile and 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws including taking down existing roof sheeting complete all as specified and directed.
98
-
-
M&L for 10mm thick rendering in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces, rendering finished even and smooth (without using extra cement) complete all as specified and directed.
175
-
-
M&L for chipping out spilled and loose concrete cover and derusting steel reinforcement of concrete column, beam, slab, chajjas, parapets and the like as directed up to 25 to 35mm thick roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry including derusting steel wire reinforcement, providing fabric MS wire mesh 75 x 75 x 2mm as reinforcement to concrete surface applying adhesive/admixture over steel mesh and providing 25mm average thickness guniting mix using one part of OPC 53 grade and two part of sand mixed with adhesive/admixture @ pressure of 2.5 to 3.00kg/Sqcm by guniting machine and surface finished even and fair including necessary padding, shuttering/scaffolding, formwork (guniting work to be carried out up to six floors building height) complete all as specified and directed.
Note :- (a) After placing the additional reinforcement all concrete surfaces shall be thoroughly scrubbed with wire brushes, washed with water and allow to dry, apply chemistic polycretes admixture @ 2.25 kg by weight of cement all as per manufacturers instruction. (b) when polymix concreting in taking condition,guniting is done with polycretes admixture @ 2% by weight of cement all as per manufacturers instructions (polycretes admixture shall be procured from chemical adhesive Pvt Ltd Co or their authorised dealer). (c) Cost of the above aspect shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account. (d) including formwork for reconsturction if required
75
-
-
M& L for fixing rebar of required length & diameter for structural connection in RCC slab, Beams and similar situations including power drilling holes of appropriate diameters in reinforced or plain concrete upto depth minimum 100 mm or as per manufacturers specification, fixing the reinforcement in position using epoxy Arcylate based anchoring adhesive at all heights and levels, 16 mm dia hole suitable for inserting 12 mm dia reinforcement bars (TMT bar shall be measured and paid saparately) complete all as specified and directed.
45
-
-
M& L for fixing rebar of required length & diameter for structural connection in RCC slab, Beams and similar situations including power drilling holes of appropriate diameters in reinforced or plain concrete upto depth minimum 100 mm or as per manufacturers specification, fixing the reinforcement in position using epoxy Arcylate based anchoring adhesive at all heights and levels, 12 mm dia hole suitable for inserting 08 mm dia reinforcement bars (TMT bar shall be measured and paid saparately) complete all as specified and directed.
50
-
-
S&F TMT bars 5 mm dia upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with with mild steel wire (annealed) not less than 0.9mm dia or securing with clips including U-shaped stirrups with necessary welding required at site complete all as specified and directed.
65
-
-
M&L for Providing & Pouring Micro concreting M-40 grade :-
(I) Dry concrete substrate surface and free of debris & dust
(ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes).
(iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade, Make : MasterEmaco S46T of BASF or equivalent FOSROC/SIKA using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed including M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed.
Note : Form work shall be 100% leak proof. The cost of micro concrete M-40 grade & Epoxy bond coat is included in this item.
2
-
-
Dismantling wrought iron, mild steel work of any description not otherwise provided for purlins, balcony railing and similar works etc. complete all as specified and directed.
0.75
-
-
S&F joist, channels, angles, tees or other sections fixed independently with or without connecting plates, cleats with necessary welding etc as required complete all as specified and directed steel work confirming to Fe-290 Gde E 165 complete all as specified and directed.
150
-
-
M&L for two coats of synthetic enamel paint on new steel and iron surfaces over a coat of red oxide primer incl preparation of surfaces over 10 cm width of girth complete all as specified and directed.
35
-
-
M&L for demolition of cement concrete in the sunken floor and and removing rubbish and cleaning sunken portion of slab (Bottom & sides) and providing water proofing treatment as under :-
(a) Providing upto 50 mm concave coving with PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate mixed with liquid WPC to maintenance damage/smooth sunken floor surfaces. (b) Applying 15mm thick plaster in CM 1:4 admixed with WPC all around of sunken floor . (e) Fixing of GI tubing 40 mm dia of medium grade for spout length as per site for sunken floor. (b) Apply WPC with cement slowly as 1:20 ratio or as per manufacture instruction upto to top of sunken portion.
(f) Applying 2 full coats of brush bond acrylic emulsion based elastomeric water proofing coating after the primer with a min time gap of 4-6 hrs between 1st & 2nd coat.
(c) Fixing the all GI/CI/PVC pipe/fiftings of any dia (Pipe/fittings will be measured and paid separately) and laying half bricks all surrounding of the pipe/fittings.
(d) Filled the all half bricks gaps with cement mortar in 1: 3 ratio mixed with WPC 200ml per 50kg of cement.
(e) Over plaster apply WPC with cement slowly as 1:20 Ratio or as per manufacture instruction to achieve smooth surface.
(f) Provide PCC 40 mm thick 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) mixed with water proofing compound as per manufacture instruction over PCC 1:5:10 as remain portion of in sunken floor complete all as specified and directed.
(Note : Measurement will be taken as floor area of the sunken floor)
14
-
-
S&F in repair medium grade galvanised steel tubing with all fittings fixed to walls and ceilings or laid in floors for 15 mm bore GI tubings complete all as specified and directed.
50
-
-
S&F in repair medium grade galvanised steel tubing with all fittings fixed to walls and ceilings or laid in floors for 20 mm bore GI tubings complete all as specified and directed.
70
-
-
S&F in repair medium grade galvanised steel tubing with all fittings fixed to walls and ceilings or laid in floors for 25 mm bore GI tubings complete all as specified and directed.
60
-
-
S&F in repair PVC (SWR) 75 mm dia floor trap/nahani trap, plain with grating including jointing with solvent cement complete all as specified and directed.
10
-
-
Demolition of old damaged existing water proofing compound on RCC roof of any description in any position and specification and cleaning the surface thoroughly and removing materials from site of work and providing the following works :-
(a) Over 15 mm thick screed bed in cement mortar 1:4 on roof surface or concrete surfaces, finished even and smooth (without using extra cement) mixed with WPC (200ml per 50kg of bag cement) all as specified and directed. (b) Applying evenly a coat of bitumen primer @ 0.50 Kg/Sqm. (c) Applying APP modified polymeric membrane over the bitumen coat surface ,weight not less than 3.0 Kg/Sqm and over lap 100mm and sealed by torch application as per manufacture insteructions. (d) Sealing edges well into grooves & protect with CM 1:2 complete all as specified and directed.
1200
-
-
M&L for providing cement concrete as in roof kerbs, levelling courses for making proper gradient/slope or mud stops rounded or chamfered on edges with B-1, 1:2:4 using stone aggregate mixed with water proofing compound as per manufacture instruction including necessary form work and including demolition complete all as specified and directed.
Note: water proofing compound to be measured and paid separately.
4
-
-
M&L for applying a coat of aluminium paint @ 200 gm/sqm in two coats over polymeric membrene at non approchable roof complete all as specified and directed.
900
-
-
M&L for for cement concrete tiles of size 25 cm x 25 cm x 22 mm thick, machine pressed, set, jointed and pointed in neat cement slurry with grey cement and no pigment in approch roofs over and including screed bed or bedding layer of cement mortar 15 mm thick in CM 1:4 for laying floor finishes complete all as specified and directed.
300
-
-
M&L for Glazed ceramic coloured walls tiles 450x300mm, 6/7mm thick, for works on vertical surfaces such as skirting/dados of 1st quality , set and jointed in neat cement slurry and pointed in coloured cement to match including rendering 10mm thick on fair faces or other than fair faces of brick work in cement mortar 1:4, finished even and fair as in backing layer complete all as specified and directed.
40
-
-
S&F in repair 5mm thick modern mirror of size 600x750mm fixed on decorative PVC cabinet with border design suitable for wash basin cabinet with fitted with LED Front and Backlight, Stepless Dimmable Wall Mirrors with Anti-Fog, Shatter-Proof, Memory, 3 Colors, Double LED Vanity Mirror with touch off/on switch in one mirror including all fixing arrangement complete all as specified and directed.
2
-
-
S & F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket guard and railing 60 cm long complete all as specified and directed.
10
-
-
S&F in repair fancy type glass corner 300mm radius of 10mm thick toughened glass with CP railing fixed with screws fancy type complete all as specified and directed.
10
-
-
S&F in repair fancy type stainless steel towel rack size 600mm X 300mm including a pair of brass bracket complete all as specified and directed.
Make: CERA cat part no. F5003101, Prayag Cat Part No BA12, Somany Cat Part No 272130330101
5
-
-
S&F in repairs Good quality Connection pipe (PVC) 15 mm dia and 450/600mm long complete all as specified and directed.
50
-
-
S&F in repair Plastic water closet seat, white , closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and jointing complete all as specified and directed.
50
-
-
S&F in repair vereous china urinals, half stall urinal type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with one stop cock and brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed.
10
-
-
S&F in repair PVC (Plastic polymer Cistern) valve less, Syphonic action type, flushing cistern of capacity 10 liters with dual flush and saparate switch operated small flush: 2-3 ltr and Large flush: 8 to 10 ltrs, low level, White with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as specified and directed.
20
-
-
S&F in repair 40mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.
100
-
-
S&F in repair 32 mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.
100
-
-
S&F in repairs brass chromium plataed basin mixer with regular swimming spouts suitable for WHB with connecting legs/ flanges) complete all as specified and directed.
4
-
-
S&F in repair bib taps fancy type chromium plated 15mm bore dia of pipe with crutch or butterfly handle complete all as specified and directed.
50
-
-
S&F in repair rotational moulded polythene water storage tanks in triple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 500 ltrs incl making connection with fitting for inlet & outlet pipe complete all as specified and directed.
20
-
-
All as per item no 110.00 above but capacity 1000 ltrs incl making connection with fitting for inlet & outlet pipe complete all as specified and directed.
6
-
-
All as per item no 110.00 above but capacity 2000 ltrs incl making connection with fitting for inlet & outlet pipe complete all as specified and directed.
2
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%