Military Engineer Services Tender
If you're typing tender ID over and again or finding it difficult to go through the cumbersome government websites for looking at Delhi tenders online. We have come up with a solution i.e. we have collated every eprocurement Delhi tender on BidAssist. Also, for any queries related to an e-tender Delhi, like the bidding process, registration process, etc., the same are explained below.
Costs
EMD
₹ 99,960Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_647675_1Bid Award Id
ViewTender No
GE/DE-128/2023-24Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
REPAIR/ MAINT OF WOODEN AND STEEL FURNITURE AND TRADE PATTERN/ SPECIAL FURNITURE ITEMS AND ITS POLISHING AT BASE HOSPITAL COMPLEX/ BSO FURNITURE YARD UNDER GE (EAST) DELHI CANTT-10
BOQ Items
S&F in replacement of new top short rail of size 375mm x 50mm x 25mm duly polished.
105
-
-
S&F in replacement of new stiffener of size 975mm x 50mm x 25mm duly polished.
90
-
-
S&F in replacement of new top of Table writing with E26. Edge should be covered with 6mm thick teak wood beading duly polished. (Make-Kitply/ Novapan/ Green Panelmax)
90
-
-
Repair and replacement of new drawer of table writing made to shape and size, front of the drawer shall be 18/19mm thick pre-laminated exterior grade MDF board OSL (Grade I) with 02 Nos knobs as per drg and as directed by Engr-in-Charge. (Make-Kitply/ Novapan/ Green Panel)
95
-
-
S&F of ply wood 3mm thick one side teak faced in front, rear and both side of table writing duly polished and as directed by Engr-in-Charge.
90
-
-
Repair/ replacement of new shutter for table writing with new 18" long piano type hinge, one knob made from 18mm/19mm thick pre laminated particle board, edges should be covered with 6 mm thick teak wood beading.
95
-
-
Side board (FD-241)
-
-
-
Removing the existing unserviceable Top and S&F new top made out of 18/19mm thick pre-laminated exterior grade MDF board OSL (Grade I) (Kitply/greenply/ Green Panel) all as specified and as shown on drgs.
12
-
-
Removing the existing unserviceable side and S&F new side made out of 18mm/19mm thick pre laminated particle board (Kitply/greenply/Green Panel) all as specified and as shown on drgs.
12
-
-
Removing the existing unserviceable back of side board and S&F new back with 6mm thick plywood commercial and duly polished all as specified and as shown on drgs.
12
-
-
Removing the existing unserviceable Top drawer and S&F new pre laminate particle board 18mm thick (Kitply/Greenply) for front of drawer and teak wood for both side and rear side of drawer and 6mm commercial plywood used for bottom of the drawer and French polished to be done only front side of the drawer all as specified and as shown on drg.
12
-
-
Removing the existing unserviceable shutter and S&F new shutter made out of 18/19mm thick pre-laminated exterior grade MDF board OSL (Grade I) particle board (Kitply/greenply/ Green Panel) including hinges and locks all as shown on drgs (Each shutter will be measured as single unit).
6
-
-
Removing the existing unserviceable bottom of side board and S&F new bottom made out of 18mm/19mm thick plywood commercial type and painted with two coats or synthetic enamel paint over a coat of primer all as specified and as shown on drgs.
12
-
-
Removing the existing unserviceable leg frame and S&F new teak wood leg frame with legs duly polished all as specified and as shown on drgs.
12
-
-
Table dining 6 persons/ 8 persons (FD-30/239/ 273)
-
-
-
Removing the unserviceable damaged Top and S&F top with new 18/19mm thick pre-laminated exterior grade MDF board OSL (Grade I) (Kitply/greenply/ Green Panel) 4mm thick teak wood edgings duly polished all around all as specified and as shown on drgs.
20
-
-
Replacement of old unserviceable leg from existing Table dining 06/08 persons and supply and fixing the same size new leg made out of Ist class hard wood teak/seasam to table dining 06 persons duly french polished all as shown on drawing and as directed by Engineer-in-Charge.
50
-
-
All as per srl item No. 3.01 here-in-before but long rail of table.
45
-
-
All as per srl item No. 3.01 here-in-before but short rail of table.
50
-
-
All as per srl item No. 3.01 here-in-before but stiffener of table.
40
-
-
S & F wooden corners made of first class hard wood teak/seasam to legs jointing top rails each with 04 Nos of steel screws.
60
-
-
Table 900mm x 600mm x 760mm with drawer/ without drawer (FD-41/224/283)
-
-
-
Removing the existing unserviceable Table Top and S&F new top with 18/19mm thick pre-laminated exterior grade MDF board OSL (Grade I) with 4mm thick teak wood edging duly polished all around all as specified and as shown on drgs. (Make-Kitply/ Novapan/ Green Panel)
90
-
-
Removing the unserviceable front leg and S&F new front leg duly polished all as per drg and as directed by Engr-in-Charge.
180
-
-
All as per Srl item No 4.02 above but back leg only.
175
-
-
Removing the unserviceable side rail of seat frame and S&F new frame duly polished all as per drg and as directed.
105
-
-
All as per Srl item No 4.02 above but front rail of seat frame.
76
-
-
All as per Srl item No 4.02 above but back rail of seat frame.
76
-
-
Removing the unserviceable back rest stiffener and S&F new stiffener only polished all as shown on drg and as directed.
92
-
-
Removing the unserviceable bottom stiffener and S&F new stiffener duly polished all as shown on drg.
88
-
-
Sofa set 5 Seater with FRC (FD/MAP-II/02)
-
-
-
S&F in replacement of foam cushion (ISI marked IS: 1741) 10 Nos in each set of sofa 3 pieces, 5 seater size of cushion 22" x 20" x 4" thick 32 density and tapestry cloth of best quality as approved complete all as per drg and as specified and directed (10 Nos cushions to be replaced) in each sofa set Make-Sleep Well/ Coir foam/ Feather foam/ JJ foam)
33
-
-
Chair Easy (FD-280,FD-229, FD-282, FD-279 & FD-75)
-
-
-
Removing of Teak Wood unserviceable front leg and S&F new legs of teak wood duly polished as per drg and as directed by Engr-in-Charge.
30
-
-
All as per Srl item No 6.01 above but back leg only.
30
-
-
Removing the unserviceable side rail of seat frame and S&F new side rail duly polished all as per drg. The caning holes 12.5 mm centre to centre all as per drg.
30
-
-
All as per Srl item No 6.03 above but front rail of seat frame.
25
-
-
All as per Srl item No. 6.03 above but back rail of seat frame.
30
-
-
Removing the unserviceable back rest stiffener and S&F new stiffener duly polished as shown on drg.
30
-
-
Removing the unserviceable arm rest all as per shown on drg.
30
-
-
Repair to Chair Dining (FD-279):
-
-
-
Removing the unserviceable front leg and S&F new front leg duly polished all as per drg and as directed by Engr-in-Charge.
260
-
-
All as per Srl item No 7.01 above but back leg only.
240
-
-
Removing the unserviceable side rail of seat frame and S&F new frame duly polished all as per drg and as directed.
180
-
-
All as per Srl item No 7.03 above but front rail of seat frame.
175
-
-
All as per Srl item No 7.03 above but back rail of seat frame.
175
-
-
Removing the unserviceable back rest stiffener and S&F new stiffener only polished all as shown on drg and as directed.
175
-
-
Removing the unserviceable bottom stiffener and S&F new stiffener duly polished all as shown on drg.
175
-
-
Repairs to Table 3' x 3' x 2 1/2' (900 x 900 x 760mm) (FD-291)
-
-
-
Removing of old unserviceable top to table, S&F table top made of pre-laminate particle of 18mm thick exterior quality type-I, gde-II duly fixed PVC beading as per FD and as directed by Engr-in-Charge. (Make-Kitply/ Novapan/ Green Panel)
60
-
-
All as per Ser item No 8.01 above but S&F long rail duly polished.
20
-
-
All as per Ser item No 8.01 above but S&F leg of table duly polished.
38
-
-
Table Dressing W/M Ladies(FD-32 (M) & FD-251)
-
-
-
Removing of old unserviceable 'D' figure mirror 5mm thick and S&F of new mirror size as per drg. Make-Atul/ Modiguard. Mirror shall be fixed in frame after providing rubber packing of required size before fixing of back ply.
25
-
-
S&F of new back ply of Mirror made out of teak wood commercial 6mm thick Make- Kit Ply/green ply after removing old unserviceable ply.
25
-
-
Removing of old unserviceable glass shutters including aluminium channel and S&F of new glass shutter including aluminium channel as shown in drawings and approved by Engineer-in-Charge.
25
-
-
Removing/ dismantling of old unserviceable shutters and S&F of new shutter/ drawer made out of teak wood commercial 12mm thick one side teak face. Make - Kit Ply/greenply.
25
-
-
Table Dressing Gents(FD-32, FD-251)
-
-
-
Dismantling of old existing unserviceable top of table dressing and S&F of new top shall be made out of 12 mm thick pre laminated particle board as specified and shown in drg.
25
-
-
Removing of existing mirror and S&F new mirror of 5mm thick back ply 6mm alongwith 4mm bedding as per drg.
25
-
-
Removing of existing unserviceable knob and S&F new knob CP brass 25mm size as approved by the GE/ Engr-in-Charge,
25
-
-
Peg Table (FD-25 (m), 270)
-
-
-
Dismantling of old existing unserviceable top of Peg Table and S&F of new top of 18/19mm thick pre-laminated exterior grade MDF board OSL (Grade I) as specified and shown on drg. (Make-Kitply/ Novapan/ Green Panel)
60
-
-
All as per Ser item No 11.01 above but front top rail/ side top rail/ stiffener & leg of 1st grade teak wood duly polished.
60
-
-
Repair to Bed plywood Top(FD-246/247)
-
-
-
Removing the unserviceable ply wood from bed top and supply & fix 12mm thick plywood(commercial of size 1980mmx900mm duly polished as shown as drg.
45
-
-
Removing unserviceable long rail and supply & fix of size 1980mmx90mmx35mm 2nd class hard wood rail made to shape duly polished as shown on drg.
35
-
-
Removing existing unserviceable/damaged OST plywood & beading of hard board and S&F 4mm thick OST plywood of size 450mmx900mm and 15mm teak wood beading made to shape duly polished as shown on drg.
40
-
-
Removing existing unserviceable/damaged OST plywood & beading of foot board and S&F 4mm thick OST plywood of size 250mmx900mm and 15mm teak wood beading made to shape duly polished as shown on drg.
40
-
-
Removing existing unserviceable Foot board and S&F new foot board of teak wood as per drg.
40
-
-
All as per ser item No. 12.05 above but Head board.
40
-
-
Recanning of all types of chair, stool dressing bin soiled linen etc
-
-
-
Recanning of steel and (including chair Verendah) wooden chairs, stool dressing, bin soiled linen etc, of different types after removing of old canes in weaving with new white plastic cane with 1.8mm wide are type and 3mm wide area for border as of approved quality complete all as per pattern shown on and all as specified in drg.
90
-
-
Peg Table Wooden 500MM X 500MM X 600MM
-
-
-
Removing of old unserviceable Glass Top from and S&F new Glass top made of 6mm thick of the top duly fixed in position all as specified and directed by Engineer-in-charge. (Make:- Modigaurd/).
16
-
-
Replacement of old unserviceable leg from existing Peg Table and S&F the same size new leg made out of Ist class hard wood teak duly french polished all as shown on drawing and as directed by Engineer-in-Charge.
32
-
-
All as per srl item No. 14.02 here-in-before but long top rail.
32
-
-
All as per srl item No. 14.02 here-in-before but bottom rail / stiffner.
32
-
-
S&F new steel bracket/corners of suitable size with steel screws all as shown on drawing and as directed.
48
-
-
TEAPOY WOODEN FD-232, 278 & 382
-
-
-
Replacement of old unserviceable leg from existing Teapoy Wooden and supply and fixing the same size new leg made out of Ist class hard wood teak/ seesam to teapoy wooden duly french polished all as shown on drawing and as directed.
300
-
-
All as per srl item No. 15.01 here-in-before but top long rail.
91
-
-
All as per srl item No. 15.01 here-in-before but top side rail.
82
-
-
All as per srl item No. 15.01 here-in-before but bottom rail / stiffner.
100
-
-
S&F new steel bracket/corners of suitable size with steel screws all as shown on drawing and as directed.
413
-
-
TABLE CENTRE FD-235/FD-274
-
-
-
Removing of old unserviceable top from table centre and S&F new top made of 18mm thick exterior grade, ISI marked particle board duly post-formed (PFT) with 0.6mm thick teak faced laminate extended upto minimum 50mm from the bottom edge and having other side white and with 02mm thick PVC edging on two short sides of the top duly fixed with strong adhesive and fixed in position all as specified and directed by Engineer-in-charge. (Make:- Ecoboard /Action- Tesa / Greenply).
45
-
-
Replacement of old unserviceable leg from existing table centre and S&F the same size new leg made out of Ist class hard wood teak/seesam duly french polished all as shown on drawing and as directed by Engineer-in-Charge.
127
-
-
All as per srl item No. 16.02 here-in-before but long top rail.
75
-
-
All as per srl item No. 16.02 here-in-before but bottom rail.
65
-
-
All as per srl item No. 16.02 here-in-before but side rail the top.
70
-
-
S&F new steel bracket/corners of suitable size with steel screws all as shown on drawing and as directed.
180
-
-
TABLE BED SIDE FD 248 & 276
-
-
-
Removing of old unserviceable top from Table bed side and S&F the new top of same size made out of 18 mm thick exterior grade pre-laminated particle board,teak faced,ISI marked all as shown on drawing check 4mm thick teakwood beading all around duly polished as directed. (Make:- Ecoboard/Action- Tesa / Greenply).
54
-
-
All as per srl item No. 17.01 here-in-before but side.
45
-
-
All as per srl item No. 17.01 here-in-before but shelf / bottom.
43
-
-
Removing of old unserviceable back ply from Table bed side and S&F the new back ply of same size of 06mm thick commercical plywood (ISI marked) including one coat of french polish all as shown on drawing and as directed.
60
-
-
STUDY TABLE WITH STORAGE UNIT SIZE OF 30"x24"x66"
-
-
-
Removing of old unserviceable top from Study table with storage unit and S&F the new top of same size made out of 18 mm thick exterior grade pre-laminated particle board,teak faced,ISI marked all as shown on drawing as directed. (Make:- Ecoboard/Action- Tesa / Greenply).
51
-
-
All as per srl item No. 18.01 here-in-before but bottom.
44
-
-
All as per srl item No. 18.01 here-in-before but Back.
40
-
-
All as per srl item No. 18.01 here-in-before but Two Sides.
90
-
-
All as per srl item No. 18.01 here-in-before but Door of.
140
-
-
All as per srl item No. 18.01 here-in-before but Shelves.
155
-
-
All as per srl item No. 18.01 here-in-before but Lock.
51
-
-
All as per srl item No. 18.01 here-in-before but Knob.
240
-
-
All as per srl item No. 18.01 here-in-before but Hinges.
480
-
-
CHAIR WRITING
-
-
-
Replacement of old unserviceable front leg from existing Chair Writing and S&F the same size new front leg made out of Ist class hard wood seesam/teakwood duly french polished all as shown on drawing and as directed.
50
-
-
All as per srl item No. 19.01 here-in-before but rear leg.
95
-
-
All as per srl item No. 19.01 here-in-before but front/back/side rail.
82
-
-
All as per srl item No. 19.01 here-in-before but back rest (i.e. horizontal wooden members for back rest of size 50mm x 15mm).
42
-
-
All as per srl item No. 19.01 here-in-before but stiffener between front leg and rear leg.
50
-
-
All as per srl item No. 19.01 here-in-before but stiffener for jointing to side stiffeners.
50
-
-
All as per srl item No. 19.01 here-in-before but arm.
87
-
-
S & F wooden corners made of first class hard wood seesam to legs joining top rails each with steel screws.
142
-
-
Polishing of the wooden furniture:- Prepare the existing surface of wooden furniture of any description by applying sand paper, removing the stains and filling the bore holes, cracks by putting bees wax & chalk powder etc and duly polished to the exposed surface polishing shall be uniform and shall be glossy finish for the following items:-
-
-
-
Bed plytop
90
-
-
Table writing/ Table office clerk
100
-
-
Side board
10
-
-
Table dining 6/8 persons
25
-
-
Sofa set five seater with FRC
40
-
-
Chair easy/ dining/ writing
390
-
-
Table dressing ladies/ gents with mirror
50
-
-
Table bed side wooden
80
-
-
Table 3' x 2' with drawer/ without drawer
100
-
-
Table peg
75
-
-
Teapoy (W)
150
-
-
Table centre
65
-
-
Table 3' x 3' x 2 1/2' (900 x 900 x 760mm) (FD-291)
60
-
-
Almirah Large steel With Shelves and 1/2 Hanging, 1/2 Shelves (FD-1031, FD-114, FD-83) :
-
-
-
Material & labour for replacement of worn out shelves made out of PBI sheet 20 gauge and fixing complete all as specified & as directed by Engr-in-Charge.
125
-
-
Fixing of existing Shelves including necessary fixing arrangements.
185
-
-
Material and labour for replacement of chromium plated MS handle complete with washer etc as approved complete all as specified and as directed by Engr-in-Charge.
190
-
-
S&F in replacement of old and unserviceable lock for Almirah large steel with new locks with duplicate keys. The lockers shall be six lever (Sample shall be approved by GE before in corporation of the work) complete all as specified and as directed by Engr-in-Charge (Make-Harrison or equivalent ISI Marked.)
196
-
-
M & L for legs made out of 1mm as thick PBI sheet channel base ends covered complete all as specified and as directed by Engr-in-Charge.
176
-
-
M & L for replacement of worn out base made out of PBI sheet 20 gauge complete all as specified and as directed by Engr-in-Charge.
158
-
-
M & L for removing of old and unserviceable MS hinges fitting 75mm long and fixing new with smoothing the welded surface complete all as specified and as directed by Engr-in-Charge.
208
-
-
M & L for locking device MS round bar 10mm dia with brass bush fitting in place of worn out fitting (Locking system) complete all as specified & as directed by Engr-in-Charge.
120
-
-
Almirah medium steel with Shelves and 1/2 H, 1/2 Shelves (FD-1032):-
-
-
-
M&L for replacement of worn out shelves made out of PBI sheet 20 gauge and fixing only complete all as specified and as directed by Engr-in-Charge.
143
-
-
Fixing of existing Shelves including necessary fixing arrangements.
136
-
-
M&L for replacement of MS CP handle complete with washer etc as approved by GE.
124
-
-
M&L for replacement of old unserviceable locks and fixing new locks with duplicate keys. The locks shall be six lever as approved by GE before in corporation in the work. (Make-Harrison/Godrej or equivalent.)
130
-
-
M&L for legs made out of 1mm thick PBI sheet channel base ends covered as specified and as directed by Engr-in-Charge.
96
-
-
M&L for replacement of worn out base made out of PBI sheet 20 gauge complete all as specified and as directed by Engr-in-Charge.
96
-
-
S&F New MS hinges 75mm long (as approved by GE) by welding, including removing old hinges and smoothing the welded surface complete all as specified and as directed by Engr-in-Charge.
185
-
-
M&L for locking device, MS round 10mm dia bar with brass bush fitting in place of worn out fitting complete all as specified and as directed by Engr-in-Charge.
106
-
-
Table office Clerk Steel (FD-84 (m):-
-
-
-
M&L for replacement old unserviceable table top with new top size 4'x2'-5" made out of 18/19mm thick pre-laminated exterior grade MDF board OSL (Grade I) and fixed 4mm thick teak wood beading all around the top duly french polished. The top shall be fixed making appropriate fixing arrangements i.e. drilling of holes, tightening of top, with appropriate size of screws wood steel complete all as specified and as directed by Engr-in-Charge. (Make-Kitply/ Novapan/ Green Panel)
100
-
-
M&L for replacement of unserviceable drawer with new drawer made to shape and size with 1mm thick PBI sheet including repairing the sliding surface of the drawer by smoothing the portion denting and welding or any other means to enable all the three drawers to work smoothly complete all as specified and as directed by Engr-in-Charge.
80
-
-
M & L for replacement of locks with new brass locks with duplicate keys complete all as specified and as directed by Engr-in-Charge.
90
-
-
M & L for replacement of PVC shoes with new PVC shoes complete all as specified and as directed by Engr-in-Charge.
200
-
-
Table office Officer Steel (FD-85(m):-
-
-
-
M&L for replacement old unserviceable table top with new top size 5' x 3' made out of 18/19mm thick pre-laminated exterior grade MDF board OSL (Grade I) and fixed 4mm thick teak wood beading alround the top duly french polished. The top shall be fixed making appropriate fixing arrangements i.e, drilling of holes, tightening of top, with appropriate size of screws wood steel complete all as specified and as directed by Engr-in-Charge. (Make-Kitply/ Novapan/ Green Panel)
77
-
-
M&L for replacement of unserviceable drawer with new drawer made to shape and size with 1mm thick PBI sheet including repairing the sliding surface of the drawer by smoothening the portion denting and welding or any other means to enable all the three drawers to work smoothly complete all as specified and as directed by Engr-in-Charge.
96
-
-
M&L for replacement of PVC shoes with new PVC shoes complete all as specified and as directed by Engr-in-Charge.
240
-
-
M&L for replacement of locks with new brass locks with duplicate keys of Make Godrej complete all as specified and as directed by Engr-in-Charge.
68
-
-
Table Dining ORs Aluminium (FD-185):
-
-
-
M&L for replacement top with new top made out of 18mm/19mm thick commercial particle board with 22 gauge thick aluminium sheet with over lapping with steel screws complete all as specified and as directed by Engr-in-Charge. (Make-Kitply/ Novapan)
10
-
-
M&L for replacement of worn out frame with new MS Square pipe 25mm x 25mm 16 gauge including stiffner where ever required complete all as specified and as directed by Engr-in-Charge.
10
-
-
M&L for welding upto 2.5 mm long welding to steel frame with electric welding and smoothening of the welding portion complete all as specified and as directed by Engr-in-Charge.
10
-
-
Table Bed side, Steel (FD-157)
-
-
-
Removing of old unserviceable broken top and supply and fixing of new top made out of 18mm/19mm thick prelaminated particle board. (Make - Kitply/ Novapan) including Teak wood beading 4mm thick all around duly french polished shall be provided.
380
-
-
Removing of old unserviceable knob with locking strip and supply and fixing of new knob with flat iron strip and locking strip made out of Flat iron 15x3 mm duly approved by GE/ Engr-in-Charge.
380
-
-
Removing of old unserviceable and broken rusted legs and S&F of new legs made out of MS square pipe 25mm x 25mm x 18 gauge as per shape/ size shown in drg. Fixing of legs shall be done by gas welding continuously and smoothened with File steel as approved by GE/ Engr-in-Charge.
540
-
-
Removing of old unserviceable PVC shoes and S&F of new shoes of PVC of required size as shown in drawing and approved by GE/ Engr-in-Charge.
700
-
-
Chair visitor cushined (TP)
-
-
-
Removing the unsv handles of chair & S&F new handles with screw steel as directed by Engr-in-Charge.
188
-
-
Removing unserviceable upholstory and S&F of foam over lining cloth, Hessian cloth as directed by Engr-in-Charge on both seat & back.
292
-
-
Rack Side Steel with Tray (FD-97)
-
-
-
M&L for removing of unserviceable shelf, S&F new shelf rack side steel 1 mm thick PBI sheet channel base end welding complete as required and shown on drg
30
-
-
Screen moveable 3 fold steel with curtains (FD-83)
-
-
-
Removing the repairable parts duly dents & bents with sliding arrangement and fixed with duly welding and smooth edges as per drg( welding point)
20
-
-
Removing the old curtain of screen moveable and S&F new curtain of green coloured cloth.
30
-
-
Removing the old wheels of screen moveable and S&F new wheels of good quality as per directed by Engr-in-Charge.
30
-
-
Locker bed side Steel /Steel Locker 4/6 Unit (FD-257,FD-243) : Repairs to Lockers Steel and replacement of components as under :-
-
-
-
S&F in replacement of worn out shelves with new made out of PBI sheets 1 mm thick and fixing 4 Nos cleats as per drg made shape 4 size including two coat of enamelled olive green paint over a coat of metal primer complete all as specified and as directed by Engr-in-Charge. Make - Nerolac /Berger/ Asian.
180
-
-
M&L for replacement of Alluminium anodised tow handles and 100 mm long alluminium hasp & staples to lockers steel complete all as spaecified and as directed by Engr -in- charge.
120
-
-
S&F MS hinges 75 mm long by welding ,including removing old hinges and smoothening the welded surface complete all as specified and as directed by Engr-in- charge.
150
-
-
M&L for legs made out of 1 mm thick PBI sheet channel base ends covered as shown on drg complete all as specified and as directed by Engr-in-charge.
200
-
-
M&L for replacement of worn out base made out of PBI sheet 20 gauge complete all as specified and as directed by Engr-in-Charge.
100
-
-
Step stand two tier steel (FD-131)
-
-
-
Removing the repairable parts duly dents and bents and fixed with the proper welding and smooth edges as per drg (welding point)
30
-
-
Chair Visitor Cushioned set of 3 chair welded together.
-
-
-
Removing unsv upholstory and S&F of foam 50 MM thick 32 density (make -feather foam/sleepwell and change of tapestry cloth not less than of Rs 150/RM as directed by Engr-in-Charge on both seat & back.
132
-
-
S& F of Adjustable Bolt
365
-
-
Charpoy GI pipe (FD-220)
-
-
-
Removing the existing broken long rails and supply & fix 32mm of dia GI long rail med grade of size 1900 mm duly threaded both ends as shown on drg for one leg.
430
-
-
Cutting and threading for short rails of size 810 mm from broken long rail and threaded both ends as shown on drg.
300
-
-
Removing the existing broken short rails and cutting and threading of leg of size 400 mm out of broken short rail as shown on drg.
230
-
-
S & F check nut of size 32mm dia 6mm thick conforming to ISI.
360
-
-
Removing the existing unserviceable 3 way GI elbow 32mm dia and S&F 3 way GI elbow 32mm dia ISI marked.
600
-
-
S&F in replacement of unserviceable top of Charpoy to be made of 12 mm thick (7Ply) commercial plywood BWR grade, confirming to IS 303-1989 and ISI marked and to be fixed with appropriate sizes of SS nuts & bolts with washers without having any joints after tightening of frame. Make : Kit Ply/Green Ply/Century Ply/Archid Ply with shape and size as per drg and as directed by Engr-in-Charge.
415
-
-
REPAIR TO CHARPOY PLY TOP STEEL FRAME
-
-
-
S&F in replacement of unserviceable top of bed hard steel to be made of 12 mm thick (7Ply) commercial plywood BWR grade, confirming to IS 303-1989 and ISI marked and to be fixed with appropriate sizes of SS nuts & bolts with washers without having any joints after tightening of frame by welding. Make : Kit Ply/Green Ply/Century Ply/Archid Ply with shape and size as per drg and as directed by Engr-in-Charge.
26
-
-
M&L, scraping of existing coat of paints complete filling, finishing and painting of Bed Hard steel with two coats of synthetic enamel paint (Make: Berger/ Asian Paint) with spray after applying a coat of red oxide primer and as directed by Engr-in-Charge.
26
-
-
S&F new PVC hard Rubber Shoes as per drg or as directed by the Engr-in-Charge.
104
-
-
REPAIR TO BED HARD PLY TOP STEEL (FD/E6/MAP/08(R) :
-
-
-
S&F in replacement of unserviceable top of bed hard steel to be made of 12 mm thick (7Ply) commercial plywood BWR grade, confirming to IS 303-1989 and ISI marked and to be fixed with appropriate sizes of SS nuts & bolts with washers without having any joints after tightening of frame by welding. Make : Kit Ply/Green Ply/Century Ply/Archid Ply with shape and size as per drg and as directed by Engr-in-Charge.
45
-
-
REPAIR TO HEAD BOARD : Removing of unserviceable board of head rest and S&F new board of Head rest to be made of 18 mm thick Ext grade MDF board of approved shade duly covered with PVC beading 2 mm thick all around (Make : Action Tesa/Novapan/Green Panel Max) of size with suitable Screws with the cleats as specified on drg and as directed by Engineer-in-Charge.
45
-
-
REPAIR TO FOOT BOARD :All as per Srl item No. 35.00 but for foot board.
45
-
-
M&L, scraping of existing coat of paints complete filling, finishing and painting of Bed Hard steel with two coats of synthetic enamel paint (Make: Berger/ Asian Paint) with spray after applying a coat of red oxide primer and as directed by Engr-in-Charge.
45
-
-
S&F new PVC hard Rubber Shoes as per drg or as directed by the Engr-in-Charge.
180
-
-
Repairs to chair CBA/ CBB Tubular Steel with arm/without arm (FD-75 (M): - Removing the existing unserviceable broken seat and back frame of tubular steel chairs, S&F new seat and back frame out of 1st class hard wood Teak duly french polished and cane for weaving as drawing with not less than 1.8mm width plastic cane for weaving and 3mm width for bordering. Canning holes shall be 12.5 mm centre to centre. Seat and back shall be fixed to frame with bolts and nuts (5mm dia and 100mm long) 04 Nos each for seat and back. Handles are to be shaped as per drawing and duly polished and fixed with suitable steel screws as directed by Engr-in-Charge.
-
-
-
Seat of chair CBA tubular steel with arms seat.
130
-
-
Back of chair CBA tubular steel with arms.
130
-
-
Seat of Chair CBB tubular steel without arms seat as per drg.
130
-
-
Back of chair CBB tubular steel w/o arms.
130
-
-
Arm rest for chair CBA tubular with arms.
140
-
-
Chair Visitor Cushioned set of 2 chair welded together.
-
-
-
Removing unsv upholstory and S&F of foam 50 MM thick 32 density (make -feather foam/sleepwell and change of tapestry cloth not less than of Rs 150/RM as directed by Engr-in-Charge on both seat & back.
50
-
-
S& F of Adjustable Bolt
120
-
-
Repair to Hot food Trolley
-
-
-
S&F Electrical Work : In this all new wiring will be install, New indicators, New
thermostate and heaters will be install.
4
-
-
S&F Rubber: New side rubbers will be install on all sides of the trolleys
56
-
-
S&F Ganj : All the trolleys will have new conatainers as per their specifications.
30
-
-
S&F Top Door : All the containers will be covered by doors which will be install on the
top with heavy duty hinges.
8
-
-
S&F Handle : side handle will be applied on the trolleys which help them to move
from one side to another.
2
-
-
S&F Wheels :Heavy duty big castors will be install as per the requirment.
4
-
-
S&F Denting and Painting of rolleys
4
-
-
Couch Examination FD 121
-
-
-
Removing of old unserviceable brocken top base and supply , fixing new top base made out of ply wood 18 mm thick commercial. (Make-Kitply/ Novapan/ Green Panelmax)
8
-
-
Dismantling of old unserviceable and brocken spring and S&F of new springs 100 mm dia as per size/Shape as shown on drg.
600
-
-
Dismantling of old unserviceable and broken 10 gauge MS wire copper plated as per size/Shape as shown on drg.
8
-
-
Removing old unserviceable upholstery and S&F of rubber foam (Sleepwell) 60 mm thick over lining cloth, Hessian Cloth, Coir, Fiber , Foam Leatherette.
8
-
-
TABLE 3'x 2' STEEL WITHOUT DRAWER :-
-
-
-
Removing of old unserviceable top from Table 3' x 2' steel without drawer and supply and fixing the new top of same size made out of 18/19mm thick pre-laminated particle board teak faced with 4mm thick teak wood beading all-around the table top all as shown on drawing and as directed. (Make :- Action-tesa/Ecoboard/Greenply/ Archidply)
25
-
-
Welding to broken joints of Table 3'X2' steel without drawer all as directed .
70
-
-
S & F in replacement PVC shoes to Table 3' x 2' steel without drawer complete all as shown on drg and as directed.
100
-
-
S & F in replacement 100mm long piece of 25 Sq mm MS tube having wall thickness of 1.6mm including welding to Table 3' x 2' steel without drawer complete all as directed by Engineer -in-Charge.
42
-
-
Painting to the Steel Furniture:- Preparing the old painted surfaces by sand papering deserting removing dents and bents and filling with putty (metal paste) painting with synthetic enamel paints two coats to give glossy finish all as directed by Engr-in-Charge.
-
-
-
Almirah large with shelf /1/2 hanging & 1/2 shelves.
165
-
-
All as per Ser item No 41.01 above but medium of size 1/2 hanging x 1/2 shelves.
150
-
-
Table office Clk steel or equivalent.
70
-
-
Table office officer steel.
65
-
-
Table dining OR's Alluminium
15
-
-
Table bed side steel
330
-
-
Chair tubular steel with arms.
100
-
-
Chair tubular steel without arms.
100
-
-
Table 3' x 2' with Drawer/ without drawer steel/ 3'x3'x760 mm or equivalent.
30
-
-
Chair easy steel.
10
-
-
Couch Examination
8
-
-
Rack adjustable/ assorted size/ 6 tier.
20
-
-
Rack Towel Steel /Step stand two tier steel
40
-
-
Stool steel 305x305x510mm
230
-
-
Chair Visitor Cushioned set of 2/3 chair welded together.
150
-
-
Chair visitor steel multiseater set of 2/3
100
-
-
Trustle Steel
50
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements