Institute Of Genomics And Integrative Biology Tender

2x 4 sqmm + 1 x 4 sq. mm earth wire

2x 10 sqmm + 2 x 6 sq. mm earth wire

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required

5/6 amp switch

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required

3 - module

12 - module

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 way , Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, single pole miniature circuit breaker suitable for inductive load of single pole in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, 240 V, 63 A, isolator / MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply of 20 to 28 W LED T-5 model ceiling Light of Alu. Body with micro reflector optics complete fitting of 4 feet, Cool White light.

Shifting if existing LED t-5 model light fitting and refixing the same light after making the necessary cutting in the zipsum fall ceiling & making good the damages with POP etc. as required cvomplete in all respect.

Cutting the total 40 mm wide and 8mm thick stainless steel plates thirteen in nos. fixed in parapet supporting a railing by Gas/Nitrogen welding along with 50 mm S.S. Pipe at two locations

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required : In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) : With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm).

Providing & fixing transparent Lamination/Film on Glass

Providing & Fixing 12.5 mm thick tapered edge gypsum moisture resistant board in MS partition frames with C.P.brass/stainless steel screws etc. Complete as per architectural drawings and directions of engineer-in-charges.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge : Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

HINGES

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm

Providing & Installing working desk made of 25 mm thick commercial board with 1.00 mm thick mica on both inner and outer side, moulding/bidding on the edges all around, commercial board 25 mm thick along with mica on both sides shall be continued all along vertically on back side (6feet 5 inches) and left side (6 feet 4 inches) except the front side. The vertical support of the same material shall be provided on these two sides with 3 feet interval, whereas on front side it will be supported by a stainless steel pipe of 50 mm dia resting on the floor. The height of the table top shall be 2.5 feet. Necessary holes in the boards are to be made for fixing the electrical fixtures. A 3 drawer pedestal made of the same material with lock is to be provided fro placing below the table. The table is to be made as per the dimensions in the drawing attached as Annexure-A with necessary minor modifications if required at site. The sample of the mica is to be approved by Department.

Providing & Installing L-shape working desk made of 25 mm thick commercial board with 1.00 mm thick mica on both inner and outer side, moulding/bidding on the edges all around, commercial board 25 mm thick along with mica shall be continued all along vertically on the both sides of L i.e. on front side ( 16 feet) and right side (6 feet 5 inches). The vertical support of the same material shall be provided on these two sides with 3 feet interval. The height of the table top shall be 2.5 feet. Necessary holes in the boards are to be made for fixing the electrical fixtures. six nos. 3 drawer pedestal made of the same material with lock is to be provided fro placing below the table. The table is to be made as per the dimensions in the drawing attached as Annexure-A with necessary minor modifications if required at site. The sample of the mica is to be approved by Department.

Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. Complete : 50 mm long

Extra for providing and fixing steel beading of size 10 x 10 x 1.6 mm (box type), approved shape and section with screws instead of glazing clips and metal sash putty, in steel doors, windows, ventilators and composite units.

Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge : With Granite stone of area less than 0.50 sqm.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/ nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood : 50 x 20 mm