Military Engineer Services Tender
View complete overview of Daman & Diu MES Tender
Military Engineer Services - MES Tender
Machinery and Tools
Eprocure
Opening Date8 Dec 2023
Closing Date10 Jan 2024
Tender Amount₹ 10,50,000
Costs
EMD
₹ 21,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2023_MES_631816_1Bid Award Id
ViewTender No
8730/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Supply only Ball bearings not less than 300 grams each of Size/ No 6208 or equivalent as per site requirement complete all as specified and directed. Make : SKF or NBC or equivalent.
268
-
-
S&F hangar door wheel not less than 32.00 Kgs each, fixing in position by lifting existing hangar door to put in position, greasing and with necessary lifting, jacking, welding work including fixing of shaft with two Nos Ball bearings of suitable size with locKing pin etc complete all as specified and directed. (Note : Ball Bearing shall be measured and paid for separately)
7
-
-
M&L for re-fixing of wheel at same position (obtained from item No 1 above) after overhauling to existing hangar door wheel through greasing, alingment, changing shaft alongwith safety pins, making functionable, complete all as specified and directed.
164
-
-
S&F in repairs hangar door wheel (top of hangar door height n. exc 15m) of dia not exceeding 100mm, 30mm thick, having hole on centre n. exc 16mm dia to fix nuts and bolts to facilitate to hangar door move smoothly, fixing in position by lifting existing hangar door to put in position, greasing and with necessary welding work etc complete all as specified and directed.
60
-
-
M&L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, height n.exc 20m, fixed with self tapping screws complete all as specified and directed.
200
-
-
M&L for plain galvanised mild steel sheeting 1.25mm thick in ridge hips, valley gutters, with grade of zink coating 275 height not exc 15 Mtr complete all as specified and directed.
50
-
-
M&L Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in hangar door /cladding to wall, height n.exc 20m, fixed with self tapping screws complete all as specified and directed.
200
-
-
Fixing only pre painted galvalume roof /wall sheet of any colour as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.
150
-
-
S&F framed work as in hangar doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete (confirming to FE-290 Gde E-165) all as specified and as directed
970
-
-
S&F for flat iron as in hangar doors shutters etc confirming to FE-290 Gde E-165 all as specified and as directed
420.8
-
-
M&L for two coats of synthetic enamel paint on new steel surfaces, over 10cm in width or girth not otherwise described over a coat of red oxide incl preparation of new steel surfaces .
35
-
-
M&L for two coats of synthetic enamel paint on new steel surfaces, not exc. 10cm in width or girth not otherwise described over a coat of red oxide incl preparation of new steel surfaces .
28.8
-
-
Inspection, checking and removing of any loose materials, such as nuts, screws, nails, binding wire etc, in ceiling of hangars and tightining of loose aluminium grill by screws, nails, binding wire etc and tightining of loose nuts and bolts etc, complete all as specified and directed. (Note : Aluminium Grill and binding wire shall be measured separately)
5520
-
-
S&F SS wire of dia not more than 2mm as in binding wire for fixing grill etc.
2
-
-
Supply only aluminium anodised grill of approved design and fixing with F/U channel complete all as specified and directed by Engr-in-Charge. Note : The grill shall be of model DG-202 or any other model of make Deco or equivalent.
10
-
-
M&L for applying one coat of synthetic enamel paint over a coat of red oxide to old steel surfaces, hanger door railing including preparation of surfaces for building height not exceeding 20M complete all as specified and directed.
300
-
-
Cleaning, checking & cutting as required and repair of edges with epoxy of hanger door tracks all as specified and directed by Engr-in-Charge.
300
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements