Military Engineer Services Tender

Supply and fixing of shock treatment chart as per E-in-C's pattern size 2 feet x 4 feet aluminium board with alluminium frame & glass with housing arrangments all as directed.

Supply and fixing in repairs end termination (Heat shrinkable) joint kit suitable for 1.1 KV UG XLPE cable of size 70 to 185 Sqmm 3.5 core.

Supply and fixing in repairs end termination (Heat shrinkable) joint kit suitable for 1.1 KV UG XLPE cable of size 185 to 300 Sqmm 3.5 core.

Taking down existing old unserviceable and supply and fixing PVC flat twin core LT cable size 4 Sqmm, 2 core keeping aside for reuse/removal from trenches/ wall/pole complete all as specified and directed.

Dismantling old unsv and S&F Stay assembly complete with accessories as shown in electrical plate No-1 (loop type insulator, stay clamps, excavation and concrete measured separately) with stay rod 16mm dia, MS plate 6mm thick size 230x230mm, complete, all as specified and directed.

Replacement old unsv and S&F Electric rubber hand gloves 33 KV

Taking down existing old unserviceable underground LT cableSupply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 16 Sqmm 4 core complete all as specified and directed.

All as per item No. 10 here-in-before but for cross sectional area 25 Sqmm 3.5 core complete.

All as per item No. 10 here-in-before but for cross sectional area 50 Sqmm 3.5 core complete.

All as per item No. 10 here-in-before but for cross sectional area 70 Sqmm 3.5 core complete.

All as per item No. 10 here-in-before but for cross sectional area 95 Sqmm 3.5 core complete.

All as per item No. 10 here-in-before but for cross sectional area 120 Sqmm 3.5 core complete.

All as per item No. 10 here-in-before but for cross-sectional area 240 Sqmm 3.5 core complete.

All as per item No. 10 here-in-before but for cross-sectional area 400 Sqmm 3.5 core complete.

Supply and fix in replacement of MCB 4pole isolater TPN 80 Amps capacity AC 415 Volts complete all as specified and directed

Taking down old unsv solar light and Supply and fixing LED solar light fitting 24 watt including galvanized steel pole in built, lithium ion battery, solar panel charge controller with dusk down sensor complete

Supplying & Laying in replacement of synthetic rubber insulated mats 3.0mm thick for voltage upto 33 kv size 2 meter long 1 meter width (2x1m) as required at site complete all specified and directed.

Dismantling old unsv and Supply, installing, testing & commissioning of LT sheet metal enclosure outdoor type dust & Vermin proof (duly painted with powder coating 6 tank process). Cable lugs are to be used to terminate cables/wires, and necessary connections all as directed by Engineer-in-Charge, self supporting fabricated out of CRCA steel sheet 3.15 mm thick, of size (1000x700x350) with base mounted on angle iron frame (40x40x4 mm) incldg 4 Legs 60 cms long made of angle iron (40x40x4 mm) grouted 30 cms below ground with PCC 1:2:4, cubicle type comprising of following:- (a) Onload Changeover Switch 200 Amps, 4 pole - 01 Nos. (b) Digital Volt meter, AC, single phase 0-500 volt 48x96 mm, 3 1/2 digit, -03 Nos. (c) Digital Amp meter, AC, 0-100 Amps 48x96 mm, 3 1/2 digit incldg CT (100 : 5), -03 Nos. (d) Digital frequency meter, AC, single phase 50 Hz, 48x96 mm, 3 1/2 digit, -01 Nos. (e) Aluminium bus bar 400 amps rating

Supplying & fixing in replacement of connection/junction box made out of 1.6mm thick MS sheet front openable, weather & vermin proof including painting two coats of synthetic enamel paint over a coat of red primer connection box shall be suitable for housing & including aluminium bus bar 25 Amps cap - 2 Nos, MCB SP 6 Amps- 01 No and having provision of cable hole in bottom for two to three cables of size 16 Sqmm 4 core armoured cable connection box shall be fitted on street light pole and fixing arrangements i.e. MS clamps etc deemed to be provided by the contractor, size of box - 200 x 150 x 100mm, complete, all as directed.

Dismantling old unsv and Supplying & fixing in replacement of double walled corrugated HDPE duct pipe of 63 mm outer dia confirming to IS-14930 (Part-II) of approved colour with fittings for cable protection complete all as specified and direcetd.

Dismantling old unsv and Supply and erecting steel tubular swaged type pole 410 SP 31 (9 mtr long) including foundation complete with cast iron /MS base plate of size 300mmx300mmx6mm continously welded at the centre of the pole and MS cap at the top of the pole all as specified including factory painted with two coats of black bituminous paint internally throughout and externally for embedded portion and applying of two coats of aluminium paint over a coat of red oxide primer above 1.5 mtr from GL and making of size 30 cm wide of black and white synthetic enamel paint alternately upto 1.5 m from ground level complete all as specified.

M & L PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in foundation of poles.

M & L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in copping/collar of poles and foundation of stay assembly etc complete all as specified and directed.

M & L for PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in copping of poles including taking down old PCC copping of poles all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 sqm on plan and not exc 1.5m in depth and getting in hard/dense soil complete all as specified and directed by Engr-in-charge

Returning filling in with approved excavated soil including spreading levelling watering and well ramming in layers not exceeding 25cm thick, complete, all as specified and directed.

Removing of surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Burnt bricks sub class 'B' laid flat dry across the cable for cable protection all as specified and directed.

Sand cushioning to UG cable 8cm thick before laying the cable and 15cm above the cable, stretching and testing of cable complete all as specified and directed. Note:(i) Consolidated / Punned sand shall be considered for purpose of payment (ii) Sand shall be same as specified for plastering work.

Taking down old unsv LT panel board including disconnecting all electric connection and accessories, Supply, installing, testing and commissioning of CPRI approved LT distribution panel floor mounted outdoor type, weather / vermin proof, made out of 3.15mm thick CRCA sheet duly powder coated, mounted on 75x75x6mm (ISA7575) iron angles frame of height 45 cm from PCC bedding, factory assembled compartmentalized construction, free standing type, 3 phase and neutral 600 amps current carrying capacity copper bus bar with epoxy insulated coating with colour code and insulated support, cable galleries inter connectiong bus bar connection / linkage complete and conforming to IS 8623 and IP 54 class of protection as per IS 2147 complete of suitable size to accomodate the items given below, including making connection of cables of incoming and outgoing with thimble / lugs, including the accessories as below complete and mounting the panel board on gound / floor with PCC (1:3:6) beddding upto a height of 30cm above ground level complete all as specified and directed by Engr-in-Charge :- (a) Incoming : (i) MCCB 4 pole 400 Amps 36 KA at 415 Volts - 1 No (b) Out going : (i) MCCB 4 pole 160 Amps 36 KA at 415 v - 1 Nos (ii) MCCB 3 pole 100 Amps 25 KA at 415 v - 3 Nos (c) Copper bus bar 600 amps for 3 phase & neutral - 1 set. (d) Digital voltmeter with selector switch 0 to 500 Volts -01 No. (e) Digital Ammeter with selector switch and CTs 0 to 500 Amps -01 No. (f) LED type indicator lamps (RYB) - 01 set.

Taking down old unsv LT panel board including disconnecting all electric connection and accessories,Supply, installing, testing and commissioning of CPRI approved LT distribution panel floor mounted outdoor type, weather / vermin proof, made out of 3.15mm thick CRCA sheet duly powder coated, mounted on 75x75x6mm (ISA7575) iron angles frame of height 45 cm from PCC bedding, factory assembled compartmentalized construction, free standing type, 3 phase and neutral 1000 amps current carrying capacity copper bus bar with epoxy insulated coating with colour code and insulated support, cable galleries inter connectiong bus bar connection / linkage complete and conforming to IS 8623 and IP 54 class of protection as per IS 2147 complete of suitable size to accomodate the items given below, including making connection of cables of incoming and outgoing with thimble / lugs, including the accessories as below complete and mounting the panel board on gound / floor with PCC (1:3:6) beddding upto a height of 30cm above ground level complete old acb deposit age e/m store yard all as specified and directed by Engr-in-Charge as (a) Incoming : (i) ACB 4 pole 1000 Amps 36 KA at 415 Volts - 1 No (b)Out going : (i) MCCB 4 pole 250 Amps 36 KA at 415 Volts - 3 Nos (ii) MCCB 3 pole 100 Amps 25 KA at 415 Volts - 3 Nos (c) Copper bus bar 1000 amps for 3 phase & neutral - 1 set. (d) Digital voltmeter with selector switch 0 to 500 Volts - -01 No. (e) Digital Ammeter with selector switch and CTs 0 to 500 Amps -01 No. (f) LED type indicator lamps (RYB) - 01 set.

Supply & fix in replacement of MCCB 4 Pole 'C' series 630 amps capacity AC 415 V,35kA complete all as specified and directed.

Supply and fix in replacement of MCCB 4 pole 400 Amps 36 KA capacity AC 415 Volts complete all as specified and directed.

Supply and fix in replacement of MCCB 4 pole 200 Amps 36 KA capacity AC 415 Volts complete all as specified and directed. .

Supply and fix in replacement of MCCB 4 pole 160 Amps 36 KA capacity AC 415 Volts complete all as specified and directed.

Supply and fix in replacement of MCCB 4 pole 100 Amps 25 KA capacity AC 415 Volts complete all as specified and directed

M&L for renewal of earthing of poles/system with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick, buried vertically in ground not less than 2.25 metres below ground level with top edge of the plate not less than1.5 mtr below ground level, connected to GI strip 32x6mm by means of nuts, bolts and washers and encased in and inclduing 40mm dia GI light grade pipe upto 2.4 mtr height from ground level fixed by MS flat iron clamp 40mmx5mm with nut, bolt and washers, GI strip fixed to base along pole and connected to existing system with alternate layers of charcoal dust, salt packed around plate 150mm thick including watering GI pipe, medium grade 20mm dia, 1.5mtr long fixed to funnel with wire mesh complete with PCC chamber and RCC chamber cover all as per electrical plate No. 3 SSR part I-2009 including excavation and earth work in any type of starta and testing on completion. (Note:- GI strip and GI pipe beyond 7.5M long shall be measured and paid separately)

S & F illuminated display board with name of Electric supply installations (sub station) of size 1.25m x 0.2m x 0.9m (LxBxH) with flex of light blue (MES Colour) colour of letters shall be white, outer side fabrication bordered with aluminium angle frame of 25mmx25mmx3mm thick, inner side fabricated with 12mm MS square bar, 50mm dia GI Pipe medium grade shall be fixed both side of board with 2 nos 30mmx4mm thick MS Flat of 2m length welded to GI Pipe and nut bolt and washer with display board not less than 3m and PCC 1:2:4 type B1 for foundation including all internal wiring and illuminated with LED 20W Tubelight fittings 02 Nos including its fixing arrangement and written letters in capital, size of letters proportion with overall size of board complete all as specified and directed . Note: (i) Before manufacturing boards drawing and design of board including colour of board shall be approved by Engr-in-Charge (ii) Each board display name shall be given seperately.