Military Engineer Services Tender

(c) Trailing cable as PVC insulated and PVC sheathed 1100 Volts grade ISI Marked multistranded copper conductor cable 6 Core 2.5 Sqmm size.

(d) Lightning protection finial with GI single spike as per manufacturer approved.

(e) Earthing complete with galvanised steel plate electrodes with 25 X 3 mm strip og GI as per manufacturers approved.- 02 Nos.

(f) Pole drawing and RCC/PCC foundation work with M20 grade concrete for errection of pole shall be carried out as per manufacturers approved drawings.

(g) LT FEEDER PILLAR BOX Supply, installation, testing and commissioning, factory made and tested, LT feeder pillar box ,outdoor type , platform mounted. The panel shall be dust and vermin proof, IP65 class protection and made out of 3.15mm thick CRCA MS sheet and 40x40x4mm thick angle iron frame work, powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front opening type, with aprons for cable entry, with double door shutter and locking arrangement including provn of 65mm Godrej (Freedom) stranded lock with 2 keys, internal wiring with PVC insulated, stranded copper conductor FRLS cable, IS-694 marked of adequate size but not less than 6.0 Sqmm. The following items accommodated with this feeder pillar including 02 Nos danger notice plate made of 1.6mm thick mild steel sheet, vitreous enameled white of size 25cm x 20cm with letter figures and conventional skull bones in signal red colour and fixed nuts, bolts and washers etc with voltage and danger indicated in Hindi and English complete all as specified and directed. The scope of work includes the following items accommodate the same panel. (i)    Stag type, 4 way terminal (I/P) 63 Amps – 01 No (PCB 150 ACBC) (ii)  MCCB 4 Pole, 415 volts AC grade, 40 Amps 25 KA Icu=100%Ics.(Make: Legrand/L&T/ SIEMENS) - 01 No (iii) Contactor 3 pole 32 Amps – 01 No (Legrand/L&T/SIEMENS) (iv) Toggle switch 6 Amps – 01 No (v) Timer (analogue) with battery backup – 01 No (Legrand/L&T/SIEMENS) (vi) Stage type, 4 way terminal (O/P) 63 Amps-01 No (PCB 150 ACBC) (vii)        Over load relay 2/3.5A – 01 No (Legrand/L&T/SIEMENS) (viii)      F. contractor 9 A – 01 No (Legrand/L&T/SIEMENS) (ix) R. contractor 9A – 01 No (Legrand/L&T/SIEMENS) (x)  Motor terminal 32 Amps – 01 No (Legrand/L&T/HPL) (xi) Push switch terminal (STD) – 01 No (Legrand/L&T/SIEMENS) (xii)        Push switch (F/R) (STD) – 01 No (Legrand/L&T/SIEMENS)

(h) PCC foundation work for LT control Panel as per manufacturers approved drawings.

(j) Earthing complete with galvanised steel plate electrodes with 32 X 6mm strip of GI as per manufacturers approved.- 02 No

(k) Work to be executed by the manufacturer or there authhorized rep and MOU undertaking of the same from the manufacturer be submitted prior to excution of work .

Supply, installation and commissioning of 12.50 Mtrs high mast system with its accessories. Mast shaft shall be in two sections,hot dip galvanised inside and outside and suitable for wind velocity as per IS 875 and including head frame, steel wire rope 6 mm dia (7/19 construction), trailing cable, double drum winch, Galvanised Lantern carriage drum winch arrangement suitable for 8 (Eight) luminaires symmetrically and lightning finial. The mast shall have an integral power tool installed inside the base compartment for its operation with minimum 0.75 HP three phase electric motor, foundation bolts manufactured from special steel along with nuts, washers, anchor plates and templates. The high mast lighting system supplied with the following accessories. Make : Bajaj/Crompton /Havells/Surya

(a) LED flood light luminaires 200/210 Watts IP 66 type with lens incl standard fittings pressure die cast aluminium housing with heat reistant toughened front glass housing with epoxy powder coated finish and , complete with control gear box and all accessories duly prewired.- 08 Nos. Make: Bajaj/ Crompton /Havells/Surya /Jaquar

(b) Low intensity twin type aviation obstruction lamp of GLS type with super bright red LED 300 Nos per lamp of IP – 65 protection aviation obstruction light complete all as directed.Make – CG / Havells / Bajaj / Surya .

(c) Trailing cable as PVC insulated and PVC sheathed 1100 Volts grade ISI Marked multistranded copper conductor cable 5 Core 2.5 Sqmm size.

(d) Lightning protection finial with GI single spike as per manufacturer approved.

(e) Earthing complete with galvanised steel plate electrodes with 25 X 3mm strip og GI as per manufacturers approved.- 02 Nos.

(f) Pole drawing and RCC/PCC foundation work with M20 grade concrete for errection of pole shall be carried out as per manufacturers approved drawings.

(g) LT FEEDER PILLAR BOX Supply, installation, testing and commissioning, factory made and tested, LT feeder pillar box ,outdoor type , platform mounted. The panel shall be dust and vermin proof, IP65 class protection and made out of 3.15mm thick CRCA MS sheet and 40x40x4mm thick angle iron frame work, powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front opening type, with aprons for cable entry, with double door shutter and locking arrangement including provn of 65mm Godrej (Freedom) stranded lock with 2 keys, internal wiring with PVC insulated, stranded copper conductor FRLS cable, IS-694 marked of adequate size but not less than 6.0 Sqmm. The following items accommodated with this feeder pillar including 02 Nos danger notice plate made of 1.6mm thick mild steel sheet, vitreous enameled white of size 25cm x 20cm with letter figures and conventional skull bones in signal red colour and fixed nuts, bolts and washers etc with voltage and danger indicated in Hindi and English complete all as specified and directed. The scope of work includes the following items accommodate the same panel. (i)    Stag type, 4 way terminal (I/P) 63 Amps – 01 No (PCB 150 ACBC) (ii)  MCCB 4 Pole, 415 volts AC grade, 40 Amps 25 KA Icu=100%Ics.(Make: Legrand/L&T/ SIEMENS) - 01 No (iii) Contactor 3 pole 32 Amps – 01 No (Legrand/L&T/SIEMENS) (iv) Toggle switch 6 Amps – 01 No (v)  Timer (analogue) with battery backup – 01 No (Legrand/L&T/SIEMENS) (vi) Stage type, 4 way terminal (O/P) 63 Amps-01 No (PCB 150 ACBC) (vii)        Over load relay 2/3.5A – 01 No (Legrand/L&T/SIEMENS) (viii)      F. contractor 9 A – 01 No (Legrand/L&T/SIEMENS) (ix) R. contractor 9A – 01 No (Legrand/L&T/SIEMENS) (x)  Motor terminal 32 Amps – 01 No (Legrand/L&T/HPL) (xi) Push switch terminal (STD) – 01 No (Legrand/L&T/SIEMENS) (xii)        Push switch (F/R) (STD) – 01 No (Legrand/L&T/SIEMENS)

(h) PCC foundation work for LT control Panel as per manufacturers approved drawings.

(j) Earthing complete with galvanised steel plate electrodes with 32 X 6mm strip of GI as per manufacturers approved.- 02 No

(k) Work to be executed by the manufacturer or there authhorized rep and MOU undertaking of the same from the manufacturer be submitted prior to excution of work .

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 1100 volts grade, of following sizes complete all as specified and directed.

(a) 3.5 core x 50 Sqmm

(b) 3.5 core x 25 Sqmm

(c) 4 core x 16 Sqmm

Supply ,fabrication, installation and testing of LT out door type factory made CPRI Approved , junction box of size 900mmX600mmX400mm (over all dimension) made out of 3.00 mm thick CRCA sheet dully supported with mild steel angle iron of size 25X25X5mm vertical frame and legs with mild steel flat iron 25X5 mm in horizontal sides of the frame with front and back side openable ,single hinged door / shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 using 40mm graded stone aggregate foundation of size 0.80m X 0.6m X 0.90m depth (0.30m below ground level and 0.60m above ground level ) and connections of all outgoing / incomming existing cable of any size drawing / digging out cable from loops in trenches inclusive of necessary excavation and earthwork as required and relaying the cables including the following fitment accessories all complete as specified and as directed. (a) Alluminium bus bar of size 50 mm X 6 mm X 400mm long wrapped with PVC sleeves with maintained the colour code and provision of making holes as required with nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 nos. (b) Enamelled iron danger notice plate of 1.60 mm thick mild steel sheet of size 200 mm X 150mm , white with letters , figures and conventional skull and bones in signal red and fixed with nuts and bolts on door / shutter of JB for LT -01 No.

Excavation in trenches, in any type of soil not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil etc complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, leveling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

M & L for dry sand cushioning to underground cables with 8cm thick before laying of cables and 15cm thick after laying and stretching of cable complete all as specified and directed. Note: (Punned thick shall be measured for payment)

M & L for Old size sub class ‘B’ bricks, laid in trenches as cable covers complete all as specified and directed.

M & L for Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete.

Supply & Fixing MCCB, 4 pole, 100 Amps, 25 KA including all fixing arrangement complete all as specified and as directed.

Supply and fixing of GI tubing, light grade, 40 mm bore with all fitting lais in trenches / pole / wall for protection of cables in repairs complete.

Dismantling of OH ACSR conductor of any size and removing unserviceable conductor from site complete all as specified & as directed.

Dismantling of LT insulators any type or size complete all as specified & as directed.

Dismantling of cross arms of MS channels or angle, section etc complete and setting aside for reuse complete all as specified & as directed.

Dismantling of old unserviceable earth wire/cradles of any size or distributor span, complete all as specified & as directed.

Supply, fixing and testing of LT Aerial bunch cable on existing steel/PCC poles with XLPE insulated LT Aerial Bunch cable heavy duty 1100 volts grade with aluminium conductor of cross section area 50 sqmm X 3 core + 16 sqmm X 1 core with insulated messenger cum neutral conductor of size 35 sqmm X 1 core including all fixing accessories such as suspension clamp, piercing connector, dead end etc complete all as specifed and as directed. 

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 1100 volts grade, of following sizes complete all as specified and directed.

(a) 3.5 core x 120 Sqmm

(b) 3.5 core x 70 Sqmm

(c) 4 core x 25 Sqmm

Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 25 to 50 sqmm,Indoor/Outdoor type complete all as specified and as directed.

Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 70 to 150 sqmm,Indoor/Outdoor type complete all as specified and as directed.

Supply and errect Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 (9.0 metres long) Swan Neck type with applying two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed. (Note: Earth work & PCC foundation shall be included in this item).

M & L for cross arms, bracing clamps and back plates fabricated from structural steel section including nuts, bolts, washers etc, drilling hole for bolts in any shape or size complete with welding, binding, two coats of aluminium paint over a coat of primer for fixing flood lights complete all as specified and directed.

Supply and fixing pole mounted junction box/bus bar chamber for connection of single phase service connection of size 400x300x190 mm with 63 amps alluminium 4 nos busbar wrapped with PVC sleeves and  maintained the colour code and provision of making holes with GI nuts, bolts & washers for connections and mounted on hydrograpic insulators with nuts & bolts at both ends of busbar complete all as specified and as directed.  Make: Sintex , Cat No: GSJB4030 or equivalent model of Hensel/Rittel.

Supply and fixing pole mounted junction box/bus bar chamber for loop connection of street light cable of size 240x130x95 mm with 2 nos 32 amps aluminium busbar wrapped with PVC sleeves and  maintained the colour code and provision of making holes with GI nuts, bolts & washers for connections and mounted on hydrograpic insulators with nuts & bolts at both ends of busbar and suitable arrangement for fixing one no MCB complete all as specified and as directed.  Make: Sintex , Cat No: GSJB2817 or equivalent model of Hensel/Rittel.

Supply ,fabrication, installation and testing of LT Panel out door type factory made CPRI Approved, water and vermin proof protection of suitable size as per IS specification made out of 3.15 mm thick outdoor type CRCA sheet dully supported with mild steel angle iron of size 40 x 40 x 5 mm vertical frame and legs with mild steel flat iron 40 x 40 x 5 mm in horizontal sides of the frame with front and back side openable ,single hinged door / shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 using 40mm graded stone aggregate as in foundation of suitable size and connections of all outgoing / incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed. Note: Rate of earthwork and PCC work are deemed to be inclusive in this item.

Incoming (a) Copper strip busbar of 250 amps rated capaacity wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 Nos (b) 4 pole MCCB 160 Amps , adjustable thermal magnetic release type 415 Volts, Ics = 100% Icu, breaking capacity 25 KA including all fixing accessories with both ends spreader links - 01 No. (c) LED Neon indicator lamp (RYB), 230/250 volts, AC -01 set (set of three) Make :- Legrand/L&T/Schneider. (d) Digital voltmeter of range (0-500) volts, flush mounting type with selector switch – 01 No. (e) Digital Ammeter of range (0- 200) Amps, flush mounting type with CT’s of ratio 250/5 and selector switch – 01 set.

Outgoing (a) 4 Pole MCCB 100 Amps , adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -02 Nos (b) 4 Pole MCCB 63 Amps, adjustable thermal magnetic release type, 4 pole, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -02 Nos (c) MCB TPN 32 Amps C series , adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 10 KA breaking capacity including all fixing accessories with both ends spreader links -02 Nos (d) MCB TPN 20 Amps , 10 KA breaking capacity, C-series including all fixing accessories with lugs -01 No (e) Multifunctional Digial type timer Switch (Astro type having longitude and latitude of Indian cities memory) 240 volts AC Single Phase - 01 No (f) Power contractor 4 Pole, 40 Amps, 415 Volts, 50 Hz - 01 No (g) Enamelled iron danger notice plate of 1.60 mm thick mild steel sheet of size 200 mm X 150mm , white with letters , figures and conventional skull and bones in signal red and fixed with nuts and bolts on door / shutter of JB for LT -01 No.

Supply ,fabrication, installation and testing of LT Panel out door type factory made CPRI Approved, water and vermin proof protection of suitable size as per IS specification made out of 3.15 mm thick outdoor type CRCA sheet dully supported with mild steel angle iron of size 40 x 40 x 5 mm vertical frame and legs with mild steel flat iron 40 x 40 x 5 mm in horizontal sides of the frame with front and back side openable ,single hinged door / shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 40mm graded stone aggregate in foundation of suitable size and connections of all outgoing / incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed. Note: Rate of earthwork and PCC work are deemed to be inclusive in this item.

INCOMMING (a) Copper strip busbar of 400 amps rated capaacity wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 Nos (b) 4 pole MCCB 250 Amps , adjustable thermal magnetic release type 415 Volts, Ics = 100% Icu, breaking capacity 35 KA including all fixing accessories with both ends spreader links - 01 No. (c) LED Neon indicator lamp (RYB), 230/250 volts, AC -01 set (set of three) Make :- Legrand/L&T/Schneider. (d) Digital voltmeter of range (0-500) volts, flush mounting type with selector switch – 01 No. (e) Digital Ammeter of range (0- 200) Amps, flush mounting type with CT’s of ratio 200/5 and selector switch – 01 set.

OUTGONIG (a) 4 Pole MCCB 100 Amps , adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -02 Nos (b) 4 Pole MCCB 63 Amps, adjustable thermal magnetic release type, 4 pole, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -05 Nos (c) MCB TPN 32 Amps C series , adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 10 KA breaking capacity including all fixing accessories with both ends spreader links -02 Nos (d) Enamelled iron danger notice plate of 1.60 mm thick mild steel sheet of size 200 mm X 150mm , white with letters , figures and conventional skull and bones in signal red and fixed with nuts and bolts on door / shutter of JB for LT -01 No.

Supply ,fabrication, installation and testing of LT Panel out door type factory made CPRI Approved, water and vermin proof protection of suitable size as per IS specification made out of 3.15 mm thick outdoor type CRCA sheet dully supported with mild steel angle iron of size 40 x 40 x 5 mm vertical frame and legs with mild steel flat iron 40 x 40 x 5 mm in horizontal sides of the frame with front and back side openable ,single hinged door / shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 using 40mm graded stone aggregate foundation of suitable size and connections of all outgoing / incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed. Note: Rate of earthwork and PCC work are deemed to be inclusive in this item.

INCOMMING (a) Copper strip busbar of 300 amps rated capaacity wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 Nos (b) 4 pole MCCB 200 Amps , adjustable thermal magnetic release type 415 Volts, Ics = 100% Icu, breaking capacity 35 KA including all fixing accessories with both ends spreader links - 01 No. (c) LED Neon indicator lamp (RYB), 230/250 volts, AC -01 set (set of three) Make :- Legrand/L&T/Schneider. (d) Digital voltmeter of range (0-500) volts, flush mounting type with selector switch – 01 No. (e) Digital Ammeter of range (0- 200) Amps, flush mounting type with CT’s of ratio 200/5 and selector switch – 01 set.

Outgoing (a) 4 Pole MCCB 100 Amps , adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -02 Nos (b) 4 Pole MCCB 63 Amps, adjustable thermal magnetic release type, 4 pole, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -06 Nos (c) MCB TPN 32 Amps C series , adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 10 KA breaking capacity including all fixing accessories with both ends spreader links -02 Nos (d) Enamelled iron danger notice plate of 1.60 mm thick mild steel sheet of size 200 mm X 150mm , white with letters , figures and conventional skull and bones in signal red and fixed with nuts and bolts on door / shutter of JB for LT -01 No

M & L in repair for Earthing to machinery/equipment installed at power house/ sub station, with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to main earth GI strip of size 32 X 6 mm by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth strip protected by GI pipe 40mm dia light grade and connected to earth test point including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete