Northeast Frontier Railway Tender

Supply, Fitting, fixing of GI channel 110x50x6 mm 300 mm long with necessary clamps size 50x6 mm for Tubular pole , drilling of holes and all accessories.

Supply , fitting , fixing of GI angle size 50x50x5 mm 3000 mm long with drilling of holes and necessary Clamps and brackets.

Supply , fitting , fixing of GI angle size 50x50x5 mm 2500 mm long with drilling of holes and necessary Clamps and brackets.

Supply , fitting , fixing of GI angle size 50x50x5 mm 2000 mm long with drilling of holes and necessary Clamps and brackets.

Supply , drawing, strengthening and stringing of ACSR conductor 6/1/3.35(Rabit)) in H 008 T lines with laying conductor on ground, lifting on poles, tensioning with tension clamps, binding oninsulator, jumpering with P.G. clamp including supply & fittings of tension clamps, nuts & bolts with standard sagging in each and every span.

Supply, laying, binding of 11KV, 1Cx 50SQ mm AAAC Covered conductor including all accessories.

Supply & fitting, fixing & binding of 11 KV Polymeric Pin insulator 5KN, complete with large steel head GI pin, nut , washer etc. as required . 011

Supply and binding of 11 KV Polymeric Disc insulator , 70KN with hardware fitting.

Supply, installation, testing and commissioning of 11 KV, 3 phase GO DO Switch,400 Amps complete with operating handle & one set spare bare fuse . 013

Supply, fitting, fixing of 11 KV LA set 9 KV (RMS) , discharge capacity 10 KA .

Supplying and erection of 11KV stay set complete (galvanised) with 19/20 mm dia X 014 1.8 meter long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm, thimble, stay clamps, turn buckle (20 mm X 60 cm), 7/ 3.15 mm dia G.I. stay wire and strain insulator etc. in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Supply, drawing, straining & binding of GI guard wire on pole structure by GI bearer wire of 8 SWG & 10 SWG cross wire(1 route length consist of 2 mtrs. 8 SWG & 1 mtr.10 SWG GI wire).

Supply, laying, connection , testing and commissioning of 11 KV HT(E) , Three Core ,120 SQ. mm compact circular aluminium conductor, conductor screen with extruded semi conducting compound, , XLPE insulated , insulation screening with extruded semi conducting compound in combination with copper tape ( 0.3KA for 1 sec) , cores laid up, innersheath of PVC tape , galvanised steel flat strip armoured , and overall pvc sheathed cable conforming to is 7098 / (part-ii) 1985 with 016 the latest amendments. For cable laying Excavation of earth depth 0.90 Mtrs. into breadth 0.508 Mtrs. below the ground level and a layer of course sand of 7.5 CM thickness shall be spread over the ground before laying the cable and the cable shall be covered with a layer of course sand of 7.5 CM thickness. The bottom of cable trench shall be leveled and got rid of any sharp material. Above the Layer of Course Sand 3 inch Size Brick is to be provided for protection of cable. Cable route markers to be provided at an interval not less than 50 Mtrs. All conditions to be fulfilled as per DRG No : PCEE/ELG/DRG/2024/2 Dtd 04.10.2024.

Supply and fitting, fixing of heat shrinkable outdoor type cable termination kit suitable for 11 KV three core 120 Sq. mm cable.

Erection of earth by 50 mm dia 3 Mtrs. long (3.6 mm thickness) GI pipe , 6 SWG GI 018 wire,GI nuts, bolts including masonry materials for earthing pit, salt, charcoal etc. and construction of earth pit covered with RCC cover slab 12.7 mm thickness and watering pipe per Drawing No PCEE/ELG/DRG/2024/1 Dtd 30.09.2024

Supply, installation, testing and Commissioning of Distribution Transformer , 315 KVA, 11/0.433KV, 50C/s BIS-LEVEL-I, Copper Wound, ONAN, Vector group-Dyn-11with first filling of Transformer oil as per IS 335 and all Standard accessories . The stardard accesories includes: Name 019 and Diagram Plate, 2 Nos of Lifting Lugs, Oil filling hole with lug, Radiator, Conservator tank, 2 Nos of earthing terminal,Drain Valve, Silica Gel Beather, Arching Horn, Air-release plug. Warranty: 24 Months from date of Commissioning.(For SPRT Station) (IS for Transformer: IS 1180 (PART 1) : 2014 With Amendment 4 March 2021) All Routine test &Type test Reports to be submitted during supply of transformer.

Supply, installation, testing and Commissioning of Distribution Transformer , 63 KVA, 11/0.433KV, 50C/s BIS-LEVEL-I, Aluminium Wound, ONAN, Vector group-Dyn-11with first filling of Transformer oil as per IS 335 and all Standard accessories . The stardard accesories includes: Name 020 and Diagram Plate, 2 Nos of Lifting Lugs, Oil filling hole with lug, Radiator, Conservator tank, 2 Nos of earthing terminal,Drain Valve, Silica Gel Beather, Arching Horn, Air-release plug. Warranty: 24 Months from date of Commissioning.( BGND, SRPN,LMY,SMCP,ACPR (IS for Transformer: IS 1180 (PART 1) : 2014 With Amendment 4 March 2021) All Routine test &Type test Reports to be submitted during supply of transformer.

Cable laying for 120 SQ mm 4 core XLPE cable by excavation of earth depth 0.75 Mtrs. into breadth 0.508 Mtrs. below the ground level and a layer of course sand of 7.5 CM thickness shall 022 be spread over the ground before laying the cable and the cable shall be covered with a layer of course sand of 7.5 CM thickness. The bottom of cable trench shall be leveled and got rid of any sharp material. Above the Layer of Course Sand 3 inch Size Brick is to be provided for protection of cable. Cable route markers to be provided at an interval not less than 50 Mtrs. All conditions to be fulfilled as per DRG No : PCEE/ELG/DRG/2024/2 Dtd 04.10.2024.

Cable laying for 70/50 SQ mm 4 core XLPE cable by excavation of earth depth 0.75 Mtrs. into breadth 0.508 Mtrs. below the ground level and a layer of course sand of 7.5 CM thickness 023 shall be spread over the ground before laying the cable and the cable shall be covered with a layer of course sand of 7.5 CM thickness. The bottom of cable trench shall be leveled and got rid of any sharp material. Above the Layer of Course Sand 3 inch Size Brick is to be provided for protection of cable. Cable route markers to be provided at an interval not less than 50 Mtrs. All conditions to be fulfilled as per DRG No : PCEE/ELG/DRG/2024/2 Dtd 04.10.2024.

Supply, testing and commissioning of LT cable End termination Kit for Cable Size 50 Sq mm 4 Core.

Supply, testing and commissioning of LT cable End termination Kit for Cable Size: 70- 120 Sq mm 4 Core.

Track Crossing by Boring of 150 mm CI Pipe by using HDD machine below 2 mtr of ground level as per direction of EIC at Site. The work also includes supply fitting & fixing of Cast Iron Boring Pipe - 150 mm as per EIC at site .

Supply, fitting, fixing, testing and commissioning of of Outdoor Type LT panel board . The panel shall be metal-enclosed, free-standing compartmentalized, modular type suitable for outdoor installation. The panel shall be dust and vermin proof and the enclosure shall provide a degree of protection of not less than IP-65. The Panel shall be fabricated out of 16 SWG cold rolled steel plates & properly supported using angles & channels. The whole panel shall be mounted on a base frame made out of suitable structural, preferably ISMC Channels. Joints of any kind in sheet shall be seam welded, all welding slag grounded off and welding pitwiped smooth with plumber metal. All panels and covers shall be properly fitted and square with the frames and holes in the panel correctly positioned. The Panel shall be fully compartmentalised with front and back opening doors.. When compartment door is opened, busbar and cable alley shall be shrouded by barrier plates. All panels shall be provided with suitable cable alley and vertical bus bar alley.Each cable chamber shall have cable entry from bottom and suitable removable gland plates shall be provided for this purpose. The 027 cable chamber shall be provided with suitable supporting arrangement between the gland plate and terminals, in the middle. The cable chamber shall have a minimum width of 300 mm depending upon the outgoing cables. Each chamber shall be provided with a hinged type door opening away from the cable alley and shall be provided with black flowertype thumb screw which shall ensure tight closing. The edges of the door shall be provided with a neoprene rubber gasket to make the compartment dust proof.. The panel shall consists of the following Switchgears: Incoming: ( BUS BAR=400 Amps TPN Aluminium) (i)MCCB 4 pole 400 Amps, 25 KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection=1 NO Outgoing:(i) MCCB 4 Pole 250 Amps, 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection- 3 Nos (ii) MCCB 4 Pole 125 Amps, 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection- 1 Nos (iii) MCCB 4 Pole 63 Amps, 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection- 2 Nos (iv)LED three phase indication lamp RYB for incoming mains.(v))CT Operated 3 Phase Multifunction meter Accuracy Class 0.5, RS485 with LCD with Parameters V,A,F,PF,KW,KVA,kVAR,kWH,kVAH,Run Hours, On Hours, Phase angle, Interrupts, THD, Neutral Current, K factor- 1 No

Supply, fitting, fixing, testing and commissioning of of Outdoor Type LT panel board . The panel shall be metal-enclosed, free-standing compartmentalized, modular type suitable for outdoor installation. The panel shall be dust and vermin proof and the enclosure shall provide a degree of protection of not less than IP-65. The Panel shall be fabricated out of 16 SWG cold rolled steel plates & properly supported using angles & channels. The whole panel shall be mounted on a base frame made out of suitable structural, preferably ISMC Channels. Joints of any kind in sheet shall 028 be seam welded, all welding slag grounded off and welding pitwiped smooth with plumber metal. All panels and covers shall be properly fitted and square with the frames and holes in the panel correctly positioned. The Panel shall be fully compartmentalised with front and back opening doors.. When compartment door is opened, busbar and cable alley shall be shrouded by barrier plates. All panels shall be provided with suitable cable alley and vertical bus bar alley.Each cable chamber shall have cable entry from bottom and suitable removable gland plates shall be provided for this purpose. The cable chamber shall be provided with suitable supporting arrangement between the gland plate and terminals, in the middle. The cable chamber shall have a minimum width of 300 mm depending upon the outgoing cables. Each chamber shall be provided with a hinged type door opening away from the cable alley and shall be provided with black flowertype thumb screw which shall ensure tight closing. The edges of the door shall be provided with a neoprene rubber gasket to make the compartment dust proof.. The panel shall consists of the following Switchgears: Incoming: ( BUS BAR=400 Amps TPN Aluminium) (i)MCCB 4 pole 400 Amps, 25 KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection=1 NO (ii) On Load Changeover Switch 400Amps 4 Pole-1 No Outgoing:(i) MCCB 4 Pole 250 Amps, 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection- 2 Nos (ii) MCCB 4 Pole 125 Amps, 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection- 2 Nos (iii) MCCB 4 Pole 63 Amps, 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection- 4 Nos (iv)LED three phase indication lamp RYB for incoming mains.(v))CT Operated 3 Phase Multifunction meter Accuracy Class 0.5, RS485 with LCD with Parameters V,A,F,PF,KW,KVA,kVAR,kWH,kVAH,Run Hours, On Hours, Phase angle, Interrupts, THD, Neutral Current, K factor- 1 No (For NLP & SPTR)

Supply, fitting, fixing, testing and commissioning of of Outdoor Type Changeover panel board . The panel shall be metal-enclosed, free-standing compartmentalized, modular type suitable for outdoor installation. The panel shall be dust and vermin proof and the enclosure shall provide a 029 degree of protection of not less than IP-65. The Panel shall be fabricated out of 16 SWG cold rolled steel plates & properly supported using angles & channels. . The panel shall consists of the following Switchgears: Incoming: ( BUS BAR=250 Amps TPN Aluminium) (i)MCCB 4 pole 250 Amps, 25 KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection=1 NO (ii) On Load Changeover Switch 250 Amps 4 Pole-1 No

Supply, fitting, fixing, testing and commissioning of of Outdoor Type LT panel board . The panel shall be metal-enclosed, free-standing compartmentalized, modular type suitable for outdoor installation. The panel shall be dust and vermin proof and the enclosure shall provide a degree of protection of not less than IP-65. The Panel shall be fabricated out of 16 SWG cold rolled steel plates & properly supported using angles & channels. The whole panel shall be mounted on a base frame made out of suitable structural, preferably ISMC Channels. Joints of any kind in sheet shall be seam welded, all welding slag grounded off and welding pitwiped smooth with plumber metal. All panels and covers shall be properly fitted and square with the frames and holes in the panel correctly positioned. The Panel shall be fully compartmentalised with front and back opening doors.. When compartment door is opened, busbar and cable alley shall be shrouded by barrier plates. All panels shall be provided with suitable cable alley and vertical bus bar alley.Each cable chamber shall have 030 cable entry from bottom and suitable removable gland plates shall be provided for this purpose. The cable chamber shall be provided with suitable supporting arrangement between the gland plate and terminals, in the middle. The cable chamber shall have a minimum width of 300 mm depending upon the outgoing cables. Each chamber shall be provided with a hinged type door opening away from the cable alley and shall be provided with black flowertype thumb screw which shall ensure tight closing. The edges of the door shall be provided with a neoprene rubber gasket to make the compartment dust proof.. The panel shall consists of the following Switchgears: Incoming: ( BUS BAR=250 Amps TPN Aluminium) (i)MCCB 4 pole 250 Amps, 25 KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection=1 NO Outgoing: (i) MCCB 4 Pole 125 Amps, 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection- 3 Nos (ii) MCCB 4 Pole 63 Amps, 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection- 4 Nos (iii)LED three phase indication lamp RYB for incoming mains.(iv))CT Operated 3 Phase Multifunction meter Accuracy Class 0.5, RS485 with LCD with Parameters V,A,F,PF,KW,KVA,kVAR,kWH,kVAH,Run Hours, On Hours, Phase angle, Interrupts, THD, Neutral Current, K factor- 1 No (For GOM Station)

Supply , installation of FRP fencing, non-Corrosive, maintenance free The FRP fencing should be complete with Door and locking arrangement.The Fencing shall be antistatic and ultra violet resistant. Fencing shall be manufactured using components made in accordance with IS-6746 and IS 13410. FRP Fencing shall be made of FRP and shall be corrosion resistant and fire retardant (Low flammability) in accordance with the latest IS-6746.FRP fencing shall be supplied in completely knocked down condition and shall be of ready to use type. The fencing system shall be suitable for onsite fabrication using standard hardware and tools. ( Size 2.8+2.8+2.8+2.8=11.2 M Perimeter with 1.8 M Height= 20.16 SQM for One Location =6 Locations=20.16x6 =120.96 SQM (LBI,BGND,SRPN,SMCP,ACPR& LMY)

Construction of concrete flooring with Concrete 1:1.5:3 (1 cement : 1.5 sand: 3 graded stone aggregate 20mm nominal size for concrete flooring of substation of thickness 200 mm. Stations 3x3x0.2=10.8 for 6 Locations= 1.8x6=10.8 CUM (LBI,BGND,SRPN,SMCP,ACPR& LMY)

Supply, installation, testing and commissioning of energy efficient 7.5KW/10 HP submersible pumping set, discharge capacity: ( 240-1080) LPM for a head of (63-16) Mtrs , outlet pipe size: 80 mm

Supply, installation of Automatic Star Delta Starter in sheet steel enclosure For 12HP/9 KW pump Relay Amps 7-10 Amps with Electronic Star delta timer.

Supply of Electronic Motor Protection relay(0.5-60 Amps) , three phase CT enabled with protection:(i) Overcurrent (ii) Undercurrent(Dry Run) (iii) Phase Loss (iii) Phase sequence Reversal protection.

Supply, erection of GI Tubular Pole 8.0 Mtrs SP-14(Pole Dia : Base-139.7 mm, Middle- 001 114.3 mm, Top- 88.9 mm), Thickness: Base-4.85 mm, Middle-4.5 mm, Top-3.25 mm, weight of pole : 111 KG) .including Erection of pole strut in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling and secured with holding clamps, bolts, nuts, etc. as required.

Supply , fitting , fixing of GI angle size 50x50x5 mm 1050 mm long on GI poles with drilling of holes and necessary Clamps and brackets.

Supply , fitting , fixing of GI angle size 50x50x5 mm 1500 mm long on GI poles with drilling of holes and necessary Clamps and brackets.

Supply, drawing, straining & binding of GI guard wire on pole structure by GI bearer wire of 8 SWG & 10 SWG cross wire(1 route length consist of 2 mtrs. 8 SWG & 1 mtr.10 SWG GI wire).

Supplying and erection of galvanised stay set for overhead lines complete with 19/ 20 005 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm thick, thimble, stay clamps, turn buckle ( 20 mm X 600 mm ), 7/ 4.00 mm dia G.I. stay wire and strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required.

Supplying and erection of 100 mm X 65 mm pin insulator complete with G. I. Spindle and nuts etc. as required on pole structure as per direction of Engineer Incharge at site.

Supplying and erection of 75 mm X 90 mm shackle insulator with G. I. Bolt, nuts and straps etc. as required on pole structure as per direction of Engineer Incharge at site.

Supply , drawing, Binding of ACSR conductor 6/1/2.59(weasel)) in LTlines with laying 008 conductor on ground, lifting on poles,binding on insulator, including supply & fittings nuts & bolts with standard sagging in each and every span.

Supply, fitting, fixing of LED street light 45 W made up of pressure die cast housing with thougened glass cover, IP 66 protection, impact resistence of IK07 & 5 KV external Surge protection device , lumen output 4800 Lm,LED Chip specification : Make - CREE LED / Osram/Lumileds/NICHIA/Philips, colour temp. - 5700 K ± 300 K . Electronic Driver Powered by Inbuilt 009 electronic LED driver (SMPS based constant current supply) with lower THD, Output Open / Short Circuit protection, Phase to Phase protection, Over Voltage protection, Surge Voltage protection & other safety test as per IS 15885 Part-2/Sec 13 and BIS compliant. Housing Pressure die-cast aluminium alloy for housing (heat sink) for effective thermal management, sturdiness, excellent corrosion resistant, separate optical and control gear compartment & top opening for easy maintenance. Lumen efficacy of LED 140 lm/W Operating Voltage: 140V to 270 V AC.